Panasonic Network Camera Server BB HCS301A Geting Started Manual

Operating Instructions
[For assistance, please call: 1-800-272-7033] 115
2.21 Starting the SD Memory Recording
The SD memory recording can be started on the Trigger page.
Notes
 You can confirm the SD memory capacity on the Status page (see page 
133).
 If this product is restarted (see page 134), the SD memory recording 
starts again.
 If you remove the SD memory card and insert it again (see page 165), the 
SD memory recording starts again.
1.Click [Trigger] on the Setup page.
2.Click [SD video...

Operating Instructions
116
2.22 Transfer the Image in Transport Mode
This product can transfer the image in transport mode by E-mail or FTP.
Prepare the following requirements.
See page 48 and set up the E-mail or FTP server.
ItemSupported Feature
E-mail or FTP 
ServerOperating 
System:IPsec supported
ISP Service:Services for multiple static global 
addresses (A global address must be set 
up to the server.)
Camera ServerISP Service :Services for multiple static global 
addresses (A global address must...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 117
2.23 Transfer the Image in Tunnel Mode
This product can transfer the image in tunnel mode by E-mail or FTP.
Prepare the following requirements.
See page 51 and set up the E-mail or FTP server.
ItemSupported Feature
VPN RouterISP Service 
(in IPv4) 
:Services for static global addresses (A 
global address must be set up to the WAN 
side.)
ISP Service 
(in IPv6)
:IPv4/IPv6 Dual-Stack or IPv6 over IPv4 
Tunneling service
Camera...

Operating Instructions
118
2.24 Setting the Motion Detection
The Motion Detection page allows you to adjust sensitivity of the Motion Detection. 
Threshold: If the threshold is set low, this function sensitively detects changes.
Sensitivity: If you set sensitivity high, amplitude on the motion detection bar gets 
jumpy.
1.Click [Motion Detection] on the Setup page.
2.Click the Motion Detection bar in Threshold to set the threshold level.
3.Click the Motion Detection bar in Sensitivity to set the...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 119
Preview
The preview window displays current threshold and detection level.
 The threshold is displayed by between green and red bar.
 The detection level is displayed by between dark and light color.
Note
Setting Threshold and Sensitivity is enabled after saving, and reflect to 
preview. 
What is the motion detection?
We assume no responsibility whatsoever for any damages resulting from the use 
of the motion detection feature. We...

Operating Instructions
120
What is the sensitivity?
The sensitivity is the brightness change level for this product to detect as the motion. The 
high sensitivity setting enables this product to detect the slight brightness change. Lower the 
sensitivity to make this product to detect only the big brightness change.
Note
Lowering the threshold and heightening sensitivity enable this product easily 
to detect the trivial motion on the part of the image.
Notes
 The motion detection is activated by object...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 121
2.25 Notifying Setup of an Alarm Log
Once a day, an alarm log sent at a specified time can be checked. To enable Alarm 
Log, set Alarm or Motion Detection for Trigger Setting and check [Enable].
1.Click [Alarm Log] on the Setup page.
2.Set each parameter.
3.Click [Save] to save the settings.
 Clicking [Cancel] cancels your settings without saving changes.
4.Click [Go to Alarm Log page].
 The Alarm Log page is displayed.
Note
If...

Operating Instructions
122
SettingDescription
A setup of operation Alarm log operation can be set here.
Time Set the date and time to send alarm logs via E-mail.
SMTP Server IP 
Address or Host 
Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) 
and 3 periods such as 192.168.0.253. But 0.0.0.0 
and 255.255.255.255 are not available. Or set a host 
name (0—255 characters).
 An IPv6 address can be set.
Por t  N o. Enter a number...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 123
2.26 Changing Initial Settings on the Single 
Camera page or the Multi-Camera page
The Image Display page allows you to change initial settings (display settings when 
a user accesses this product) of image resolution, image quality and refresh 
interval. You can display a time stamp on the image. The initial language can be 
selected from eight languages. The banner can be displayed for administrator or 
general users or both....

Operating Instructions
124
SettingDescription
Image Resolution Select the image resolution.
640 × 480 pixels (Only for the Single Camera page)
320 × 240 pixels (default)
160 × 120 pixels (Only for the Multi-Camera page)
Image Quality Select the image quality.
[Favor Clarity] optimizes for good quality.
[Standard] offers standard quality. (default)
[Favor Motion] optimizes for enhanced motion.
Refresh Interval Select a refresh interval. 
Motion, 3 s, 5 s, 10 s, 30 s, and 60 s
Time stamp setting You...