Panasonic Network Camera Kx Hcm280 Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 91
3.6.12 Status
Status window displays general information about Network Camera.
Note
When some trouble occurs, the information is useful. 

Operating Instructions
92
3.6.13 Restart
Restart window restarts Network Camera with the parameters saved. Restarting 
is required when the network parameters are changed.
1.Click [Restart] on Setup Page.
2.Click [Restart Now!].
•Click [Cancel] to quit. The window returns to Setup Page. 

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 93
3.6.14 Update Firmware
Update Firmware window allows the user to install the latest version of the 
Network Camera internal operating system (Application and Camera firmware). In 
most cases, this will never be necessary. Changes may be necessary to 
accommodate new operating systems or new web browsers that are not shown on 
page 10. In those cases, Update Firmware would be available from the Network...

Operating Instructions
94
4.Click [Update Firmware] on Setup Page.
5.Click [Update Firmware].
Wait about one minute.
Note
If you click [Update Firmware], operation cannot be canceled. If canceled, 
refer to page 123. 

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 95
6.Click [Browse...] to select the firmware from the file selector.
•A dialog box appears to choose the file.
7.Select a desired Firmware file for Application or Camera (including the path 
information) and click [Open].
8.Make sure the desired firmware file name is selected correctly, and click 
[Update Firmware].
Restarting window is displayed, and Network Camera restarts 
automatically.
Restart...

Operating Instructions
96
3.6.15 Reset to Factory Default
Reset to Factory Default window initializes all the parameters including the ID, 
Password, IP address and Subnet Mask except Date and Time setting to the 
factory default. Reconfirm the settings before doing the Reset to Factory Default 
operation.
1.Click [Reset to Factory Default] on Setup Page.
2.Click [Execute].
•Indicator changes such as Orange blinking twice –> Turning off 
about 15 seconds. Initializing takes about one minute.
•Click...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 97
Section 4
Technical Guides 

Operating Instructions
98
4.1 Mounting
Two ways of mounting are shown in the following figures. MAC Address and Serial 
Number are indicated on the bottom label of the main unit of Network Camera. 
Record both of them on the Network Camera Memo on page 3. They are 
indispensable for setting network parameters after mounting Network Camera 
and for future customer servicing. 
Note
Mounting and cabling instructions described in this Operating Instructions 
follow generally accepted guidelines suitable for...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 99
4.1.2 Mounting on the Ceiling
Mount Network Camera at an even place where vibrations etc. are few. Set the Tilt 
range to [On the ceiling] on Camera Setup window on page 84. Two ways of 
wiring can be considered; wiring through a hole made in the ceiling or wiring 
without making a hole for a cable in the ceiling. Select either one of the two.
Wiring through a hole made in the ceiling
1.Fix the Ceiling...

Operating Instructions
100
2.Make a hole for a cable.
3.Fix the rubbers and dents of Network Camera to the Ceiling Plate A and fix 
them firmly.
•Make sure Network Camera, using coins etc., is firmly fixed.
4.Fix the Ceiling Plate A to the Ceiling Plate B and fix them firmly with Screws A.
Note
Install Network Camera so that the connecting part comes to the front.
Hole for a cable: 25 mm (1 inch)
65 mm (2.5 inches)
Fit the four rubbers in place.
Fit the two dents 
in place.
Fit the hooks to the holes and...