Panasonic Network Camera Kx Hcm110a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 61
 Set up the IPsec policy as below.
9.Access the camera (see page 13).
 If you can access the camera, the IPsec setup is complete.
Note
 In IPsec communications, IPsec is displayed on the Top page or the 
Single Camera page.
 If you cannot communicate using IPsec, see page 20 of the 
Troubleshooting on the Setup CD-ROM.
 See the Panasonic Network Camera support website at  
http://panasonic.co.jp/pcc/products/en/netwkcam/ for the...

Operating Instructions
62
2.7 Using UPnP™ (Universal Plug and Play)
UPnPTM can automatically configure your router to be accessed from the Internet. 
In order to use this feature, your router needs to support this feature and it must be 
enabled. Most router manufacturers disable this feature as the default setting. See 
http://panasonic.co.jp/pcc/products/en/netwkcam/ for details and see your 
routers manual for how to enable UPnP
TM. After the UPnPTM is enabled on the 
router, set [Enable] for auto...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 63
3.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed. 
4.Click [Go to UPnP page].
 The UPnP page is displayed.
2.7.1 Connecting the Camera to a Router Supporting 
UPnP™ (IPv4 Only)
To allow access from the Internet with a router supporting UPnPTM, follow the 
procedures shown on the Getting Started.
Note
 In some routers, the UPnPTM feature is disabled by default. Enable your 
routers...

Operating Instructions
64
2.7.2 Connecting the Camera to a Router Not Supporting 
UPnP™ (IPv4 Only)
To allow access from the Internet with a router not supporting UPnPTM, follow the 
procedures below.
1.Select [Static] on the Network (IPv4) page.
2.Enable port forwarding on the router.
Using the IP address and port number note written on step 1-(3), enable port 
forwarding on the router. See the router manual for how to enable port 
forwarding.
3.Register with the DynamicDNS service.
Port Forwarding...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 65
2.8 Registering with the DynamicDNS service
DynamicDNS service is a service that allows you to assign an easy-to-remember 
name to the camera, similar to your favorite web site. DynamicDNS service also 
allows you to easily access the camera, even when your ISP changes the IP 
address. Panasonic Communications recommends you to register with it for the 
Internet access to the camera. See http://www.viewnetcam.com for details about...

Operating Instructions
66
 When finished, the message dialog is displayed. 
 Clicking [Cancel] cancels your settings without saving changes.
3.Click [Go to Viewnetcam.com page].
 The Viewnetcam.com page is displayed.
4.Click Your Account Link.
 The Viewnetcam.com registration website is displayed.
Note
 When the Viewnetcam.com registration website is not displayed, 
confirm that the URL is displayed in the right column of the Your 
Account Link. If the URL is not displayed, follow the procedures...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 67
Due to the router specifications, the image may not be displayed even if you 
access the camera from your PC on the same LAN as the camera. In this case, 
access the camera in the following procedures.
 Accessing from the PC on another network (see page 13)
 Accessing from your cell phone (see page 38)
 
When you select [User-specified DynamicDNS]
1.Click [Next].
 Clicking [Cancel] cancels your settings without saving changes....

Operating Instructions
68
Note
 It may take several minutes for the registered URL to connect.
 Some DynamicDNS service is not connected.
Confirming the Internet access
Due to the router specifications, the image may not be displayed even if you 
access the camera from your PC on the same LAN as the camera. In this case, 
access the camera in the following procedures.
 Accessing from the PC on another network (see page 13)
 Accessing from your cell phone (see page 38)
2.8.1 DynamicDNS Service...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 69
How the DynamicDNS service works
1.Your ISP assigns a global IP address to your Internet access account that 
changes periodically. This is the address needed to access the camera over 
the Internet.
2.When your ISP assigned global IP address changes, your camera 
automatically notifies the DynamicDNS service server of the new address in 
the DynamicDNS. The camera notifies the DynamicDNS service server of the 
new address in...

Operating Instructions
70
2.9 Setting Date and Time
The Date and Time page allows you to set date and time. Date and time are used 
for each images (Single, Multi and Buffered), Trigger, Alarm Log and Operation 
Time.
Note
Saving the date and time settings deletes all buffered images on the internal 
memory.
1.Click [Date and Time] on the Setup page.
2.Set each parameter.
 Set [Automatic Time Adjustment] to synchronize the time automatically 
with an NTP server.
 Clicking [Cancel] cancels your settings...