Panasonic Network Camera Kx Hcm110a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 91
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
92
SettingDescription
Server IP 
Address or 
Host Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 3 
periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name (1—
255 characters).
 You can set IPv6 address.
Por t  N o. Enter a number (1—65535). Usually set to 21.
Login ID*2
*2But [] is not available.
 If your ISP requires a login ID, set it (0—63 characters)....

Operating Instructions
[For assistance, please call: 1-800-272-7033] 93
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
94
SettingDescription
SMTP Server IP 
Address or Host 
Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 
3 periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(1—255 characters).
 You can set IPv6 address.
Por t  N o. Enter a number (1—65535). Usually set to 25.
POP3 Server IP 
Address or Host 
Name
*1
 If you set the server IP address, set 4 digits (0—255)...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 95
8.Confirm the settings, and click [Save].
 New settings are saved.
 When finished, Success! is displayed.
9.Click [Go to Trigger page].
 The Trigger page is displayed.
Note
 If you are buffering images on the internal memory, the following 
operations also delete all buffered images.
– Turning off the camera.
– Saving the Date and Time page.
– Restarting, updating firmware or resetting the camera to factory 
default. 

Operating Instructions
96
2.16 Buffering or Transferring Images by Alarm 
Signal
The Trigger page allows you to enable image buffer/transfer by E-mail or FTP.
1.Click [Trigger] on the Setup page.
2.Click No. to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Alarm 1 or 2] for trigger, select 
[Rising: GND to Open (High).] or [Falling: Open (High) to GND.] and click 
[Next>].
Note
 Click [Delete Buffered Images] to delete this buffered images.
 Click [Save] to save the settings....

Operating Instructions
[For assistance, please call: 1-800-272-7033] 97
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 
70).
 Clicking [

Operating Instructions
98
5.Set the Lens Position When Triggered setting, and click [Next>].
Note
If you enable the Lens Position When Triggered setting, buffer/transfer starts 
after the camera turns to the alarm position.
 Clicking [].
 Clicking [

Operating Instructions
[For assistance, please call: 1-800-272-7033] 99
7.Set the image buffer frequencies, and click [Next>].
Note
Due to the network environment, object, number of accesses, enabling IPsec, 
the camera may not record the numbers of images as you set. In this case, set 
the image buffer frequencies longer.
 Clicking [

Operating Instructions
100
8.Select the transfer method, and click [Next>].
 Clicking [