Panasonic Network Camera Kx Hcm110a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 101
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
102
SettingDescription
Server IP 
Address or 
Host Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 3 
periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name (1—
255 characters).
 You can set IPv6 address.
Por t  N o. Enter a number (1—65535). Usually set to 21.
Login ID*2
*2But [] is not available.
 If your ISP requires a login ID, set it (0—63 characters)....

Operating Instructions
[For assistance, please call: 1-800-272-7033] 103
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
104
SettingDescription
SMTP Server IP 
Address or Host 
Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 
3 periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(1—255 characters).
 You can set IPv6 address.
Por t  N o. Enter a number (1—65535). Usually set to 25.
POP3 Server IP 
Address or Host 
Name
*1
 If you set the server IP address, set 4 digits (0—255)...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 105
9.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings seeing page 
103 and page 104. When 
finished, click [Next>] and go to step 10.
10.Click [Save] after confirming the settings.
 New settings are saved.
 When finished, Success! is displayed.
SettingDescription
Disable The camera does...

Operating Instructions
106
11.Click [Go to Trigger page].
 The Trigger page is displayed.
Note
 If you set a short interval to transfer image to a cell phone, many E-mails 
may be sent to it leading to a large phone bill. Therefore, we recommend 
you to set a long interval. 1 image per minute frequency is recommended.
 Alarm transfer stops its operations until the camera finishes all transfers. 
For example, if the camera transfers 3 images per minute and 6 images in 
total, the alarm detection will...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 107
2.17 Buffering or Transferring Images by Motion 
Detection Signal
The Trigger page allows you to enable image buffer/transfer by E-mail or FTP.
1.Click [Trigger] on the Setup page.
2.Click [No.] to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Motion Detection] for trigger, 
and click [Next>]. 
Note
 Click [Delete Buffered Images] to delete this buffered images. 
 Click [Save] to save the settings.
...

Operating Instructions
108
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 
70). 
 Clicking [>Back] takes you back to the previous page.
 Clicking [Cancel] takes you back to the Trigger page without saving 
changes.
5.Set the image settings, and click [Next>]. 
Note
If you enable the Lens Position When Triggered setting, buffer/transfer starts 
after the camera turns to the Home Position, Preset No.1–8, or...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 109
 Clicking [>Back] takes you back to the previous page.
 Clicking [Cancel] takes you back to the Trigger page without saving 
changes.
6.Set the image settings, and click [Next>].
 Clicking [>Back] takes you back to the previous page.
 Clicking [Cancel] takes you back to the Trigger page without saving 
changes.
SettingDescription
Lens Position 
When Triggered  Set the lens position when motion detection triggered....

Operating Instructions
110
7.Set the image buffer frequencies, and click [Next>].
Note
Due to the network environment, object, number of accesses, enabling IPsec, 
the camera may not record the numbers of images as you set. In this case, set 
the image buffer frequencies longer.
 Clicking [Cancel] takes you back to the Trigger page without saving 
changes.
 Clicking [