Panasonic Network Camera Kx Hcm110a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 141
3.1.7 Loading Settings from a Configuration File
The settings can be loaded from a configuration file. If you reset the camera to 
factory default, the camera can load its settings from the configuration file.
Note
 The configuration file has network settings. When the settings are loaded, 
the network settings are also loaded as they were saved. 
 If you try to update the camera, create a configuration file after updating 
the...

Operating Instructions
142
3.1.8 Resetting the Camera to Factory Default
All camera settings are reset to factory default directly after the Execute button is 
clicked.
1.Click [Reset to Factory Default] on the Maintenance page.
2.Click [Execute].
 The indicator blinks orange, and then turns off for 10 seconds.
 All camera settings (user name, password, IP address, subnet mask etc.) 
are reset to factory default.
 If the camera is reset to factory default, the network connection mode 
changes to...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 143
3.2 Support page
3.2.1 Seeing Help page
The Help page displays explanations for each feature about the following 1. to 6. 
items.
Clicking [Help] on the Support page displays the next page.
3.2.2 Seeing Product Information
You can see product information on the Panasonic Network Camera support 
website.
Clicking [Product Information] on the Support page displays the URL, click it.
Note
If the camera is not connected to the Internet,...

Operating Instructions
144
3.2.3 Seeing Support Information
You can see support information on the Panasonic Network Camera support 
website.
Clicking [Support Information] on the Support page displays the URL, click it.
Note
If the camera is not connected to the Internet, the website cannot be displayed. 

Operating Instructions
[For assistance, please call: 1-800-272-7033] 145
3.3 External I/O
If you connect the external devices such as sensors to the External I/O and image 
buffer/transfer by alarm signal is set, the camera image is transferred by the alarm 
detection.
Explanation of the External I/O
Note
The External I/O (Input/Output) is independent. Output terminal is controlled 
only by External Output Control page on page 
132.
PinFeatures
GGND pin
1External Sensor Input 1
 Use it by opening or GND...

Operating Instructions
146
Circuit Diagram Example
CAUTION
The external I/O is not capable of connecting directly to devices that 
require large amounts of current. In some case, a custom interface 
circuit (customer-provided) may have to be used. Serious damage to 
the camera may result if a device is connected to the external I/O that 
exceeds its electrical capability (see page 
145).
The low voltage/current circuits and high voltage/current circuits are 
in the camera circuit. The qualified...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 147
3.4 FACTORY DEFAULT RESET Button
The camera has a FACTORY DEFAULT RESET button on the side.
Pressing the FACTORY DEFAULT RESET button resets the camera to factory 
default. If you lose your user name and password, use this button to reset the 
camera.
 Press the FACTORY DEFAULT RESET button for 1 second when the camera 
is on.
 The indicator blinks orange, and then turns off for 5 seconds.
 Do not turn off the camera until the...

Operating Instructions
148
3.5 Default Setting List
Basic
ItemsDefaultRequiredNote
Network 
(IPv4)Connection ModeAutomatic 
Setup-Automatic Setup/
Static/DHCP
Allow Access from the 
Internet (Automatic 
Setup only)No--
Network Configuration 
from Setup Program 
(Static/DHCP only)Enable--
Port No.  
(Static/DHCP only)
80-20, 21, 25 and 110 
is not available.*2
IP address  
(Static only)
192.168.0.
253When 
setting Static*1
Subnet Mask  
(Static only)
255.255.
255.0When 
setting Static*1
Host Name  
(DHCP...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 149
Network 
(IPv6)Connection ModeAutomatic 
Setup-Automatic Setup/
Static
Allow Access from the 
Internet (Automatic 
Setup only)No--
Port No.  
(Static only)
80-20, 21, 25 and 110 
is not available.*2
IP address  
(Static only)
[Blank]When 
setting Static*1
Default Gateway (Static 
only)[Blank]When using 
Gateway*1
DNS Server 1 
DNS Server 2
[Blank]When using 
DNS*1
Max. Bandwidth Usage 
(Mbps)Unlimited-0.1, 0.2, 0.3, 0.5, 1 
or...

Operating Instructions
150
Dynamic
DNSViewnetcam.comNo checkWhen 
setting 
viewnetcam.
comViewnetcam.com/
User-specified 
DynamicDNS/
Disable
User-specified 
DynamicDNS[Blank]-Viewnetcam.com/
User-specified 
DynamicDNS/
Disable
10 min-At the time of 
starting/10, 
30(min), 1, 3, 6, 
12, 24(h)
Date and 
TimeTime SettingAM/PM--
Automatic Time 
AdjustmentNo checkWhen using 
NTP-
Time ZoneGMT -05:00--
Adjust Clock for 
Daylight Saving TimeNo check--
Start DayApr,
First Sunday,
2 AM--
End DayOct,
Last...