Panasonic Network Camera Kx Hcm110a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 111
8.Select the transfer method, and click [Next>].
 Clicking [

Operating Instructions
112
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
[For assistance, please call: 1-800-272-7033] 113
SettingDescription
Server IP 
Address or 
Host Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 3 
periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name (1—
255 characters).
 You can set IPv6 address.
Po r t N o. Enter a number (1—65535). Usually set to 21.
Login ID*2
*2But [] is not available.
 If your ISP...

Operating Instructions
114
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
[For assistance, please call: 1-800-272-7033] 115
SettingDescription
SMTP Server IP 
Address or Host 
Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 
3 periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(1—255 characters).
 You can set IPv6 address.
Po r t N o. Enter a number (1—65535). Usually set to 25.
POP3 Server IP 
Address or Host 
Name
*1
 If you set...

Operating Instructions
116
9.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings seeing page 
114 and page 115.
10.Click [Save] after confirming the settings.
 New settings are saved.
 When finished, Success! is displayed.
SettingDescription
Disable The camera does not send an E-mail notification when 
buffering or transferring image.
Enable The camera...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 117
11.Click [Go to Trigger page].
 The Trigger page is displayed.
Note
 If you set a short interval to transfer image to a cell phone, many E-mails 
may be sent to it leading to a large phone bill. Therefore, we recommend 
you to set a long interval. 1 image per minute frequency is recommended.
 Motion Detection transfer stops its operations until the camera finishes all 
transfers. For example, if the camera transfers 3 images per...

Operating Instructions
118
2.18 Transfer the Camera Image in Transport Mode
The camera can transfer the image in transport mode by E-mail or FTP.
Prepare the following requirements.
See page 55 and set up the E-mail or FTP server.
ItemSupported Feature
E-mail or FTP 
ServerOperating 
System
ISP Service 
: IPsec supported 
: Services for multiple static global 
addresses (A global address must be set up 
to the server.)
CameraISP Service : Services for multiple static global 
addresses (A global address...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 119
2.19 Transfer the Camera Image in Tunnel Mode
The camera can transfer the image in tunnel mode by E-mail or FTP.
Prepare the following requirements.
See page 58 and set up the E-mail or FTP server.
ItemSupported Feature
VPN RouterISP Service 
(in IPv4) 
ISP Service 
(in IPv6)
: Services for static global addresses (A 
global address must be set up to the WAN 
side.)
: IPv4/IPv6 Dual-Stack or IPv6 over IPv4 
Tunneling service...

Operating Instructions
120
2.20 Setting the Motion Detection
The Motion Detection page allows you to adjust sensitivity of the Motion Detection. 
Threshold: If the threshold is set low, this function sensitively detects changes.
Sensitivity: If you set sensitivity high, amplitude of motion detection bar gets jumpy.
1.Click [Motion Detection] on the Setup page.
2.Click the Motion Detection bar in Threshold to set the threshold level.
3.Click the Motion Detection bar in Sensitivity to set the sensitivity...