Panasonic Network Camera Kx Hcm110a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 31
 Audio features such as camera microphone sensitivity and mute during pan/tilt 
can be set up on the Audio page (see page 
78).
 If you are running other applications or opening multiple windows, the audio 
may be interrupted or delayed.
 When the image is refreshed during any operation such as preset registration 
or a web browser refresh, the volume is reset to the default (midrange) 
position. Audio that was muted is enabled.
...

Operating Instructions
32
 The external microphone input terminal does not correspond to a line level. 
Audio may be distorted when the line level is input. Audio distortion will be 
solved if you insert the following circuits. Under no circumstance should high 
level audio, such as from a speaker, be connected to this input terminal. Doing 
so is likely to damage the camera.
Camera
External Microphone 
Input TerminalAudio Line 
Out Capacitor Resistor
1   F 33 K 

Operating Instructions
[For assistance, please call: 1-800-272-7033] 33
1.4 Viewing Multi-Camera page
To view multiple cameras on the Multi-Camera page, you need to configure each 
camera on the Multi-Camera Setup page (see page 
128).
1.Access the camera (see page 13).
 The Top page is displayed.
2.Click the [Multi] tab at the top of the page.
 Multi-Camera page can display up to 12 camera images.
3.Close the web browser.
Capture Image Button (See page 22)
Switches cameras to 
display. If you select...

Operating Instructions
34
Note
 When selecting [All] at the View Type, all images are displayed in 160 x 
120 pixels resolution, and the Audio Control Bar is not displayed.
 640 x 480 pixels image cannot be displayed on the Multi-Camera page.
 When viewing video (Motion JPEG), we recommend using an Ethernet 
switching hub instead of the repeater hub to prevent degradation in video 
display.
 Due to the network congestion or the number of accesses, the refresh 
interval may slow down.
 When the...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 35
1.5 Viewing Buffered Image page
To buffer the images on the internal memory, you need to set up image transfer 
settings (see page 
87, page 96 or page 107). You can view buffered images on this 
Buffered Image page.
Note
Sound cannot be buffered on the Buffered Image page.
1.Access the camera (see page 13).
 The Top page is displayed.
2.Click the [Buffered Image] tab at the top of the page.
3.Click the trigger number.
The trigger...

Operating Instructions
36
4.Display images clicking buttons below.
Note
 Date, Time and frame number are not displayed in play mode.
 A still image can be saved on the Buffered Image page, if you are not playing 
images on it. Put the cursor on the image, and right-click it. Then select [Save 
Picture As...].
 Maximum number of buffered images change depending on resolution, image 
quality and what object the camera buffers. At the 320 x 240 pixels resolution 
and the standard quality, the camera...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 37
1.5.1 Deleting Buffered Images
If you intend to delete images for each transfer condition, click [Delete Buffered 
Images] on the Trigger page (see page 
87, page 96 or page 107).
Note
 If you are buffering images on the internal memory, the following operations 
also delete all buffered images.
– Turning off the camera.
– Saving the Date and Time page.
– Restarting, updating firmware or resetting the camera to factory default.
–...

Operating Instructions
38
1.6 Viewing Still Images on Your Cell Phone
You can view still images over the Internet from a compatible cell phone.
Enter http://IP address (or URL):Port Number/mobile on a cell phone and 
press [OK]. 
 When the port number is set to 80 (default), it is not required.
 The camera must be allowed the Internet access for cell phone access.
 When an authentication window is displaye d, enter the administrators or the 
general users user name and password.
 A still image is...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 39
Note
 Audio feature does not work on cell phones.
 If the features are not permitted on the General User page, the buttons related 
with the features are not displayed. (See page 
84)
 If the image is not displayed properly, try the following 2 URLs.
 When pan/tilt reaches the end, the keypad number and character disappear.
E.g.: The pan reaches the left end.
 Some cell phones are not compatible with Panasonic Network Cameras....

Operating Instructions
40
2 Various Camera Features
2.1 Using Camera Features
1.Access the camera (see page 13).
 The Top page is displayed.
Note
 When [Permit access from guest users] is set on the Security: 
Administrator page, click [Login] tab and log in as an administrator.
 When users other than an administrator are accessing the camera, the 
[Setup] and [Maintenance] tabs are not displayed.
 If [View Multi-Camera page] or [View Buffered Image page] is not 
permitted on the General User page,...