Panasonic Network Camera BL-VT164 BL-VP100 Owners Manual

Alarm image[FTP >>]
When “FTP >>” is clicked, the [FTP] tab of the “Server” page will be displayed. ( ®page 100)
[Alarm image FTP transmission]
Select “On” or “Off” to determine whether or not to transmit the alarm image to the FTP server.
• Default:  Off
[Directory name]
Enter the directory name where the alarm images are to be saved.
For example, enter “/ALARM” to designate the directory “ALARM” under the root directory of the FTP server.
• Available number of characters:  1 - 256 characters
•...

[Image compression rate upon alarm detection]
Select “On” or “Off” to determine whether or not to change the image quality of “Quality1” ( ®page 47) upon
alarm detection.
• On:  Images will be transmitted with the image quality selected for “Image quality upon alarm detection”.
• Off:  Does not change the image quality upon alarm detection.
• Default:  Off
[Image quality upon alarm detection]
Image quality can be changed upon an alarm occurrence. Select the image quality from the following.
0 Super fine/...

•Close:  The alarm output terminal will close when outputting the alarm signals. (Normally open)
• Default:  Close
Note
•When “Open” is selected, the alarm signal will be output for about 20 seconds when the power of the
unit is turned on.
[Pulse width]
When “Pulse” is selected for “Alarm output”, select an alarm output terminal duration from the following.
• Available range:  1-120s
• Default:  1s
11.5  Change the AUX name [Alarm] (BL-VT164W/
BL-VT164) Click the [Alarm] tab on the “Alarm” page. ( ®page...

11.6  Configure the VMD settings [VMD area]Click the [VMD area] tab on the “Alarm” page. ( ®page 34, page 35)
The video motion detection areas can be set on this page.
 :
The VMD areas can be set up to 4 areas for each preset position (maximum 64 preset positions). When motion
is detected in the set area, it will be regarded as an alarm. The camera can be configured to take an alarm
action even when the camera is not at the preset position.
  :
Up to 4 areas can be set. When motion is detected in the set...

VMD information addition[Information addition]
Select “On” or “Off” to determine whether or not to add VMD information to superimposed image data.
The VMD information can be searched by some Panasonic network disk recorders. Refer to the operating
instructions of the connected devices for further information about the functions and settings.
• Default:  Off
Procedure for setting the VMD area Set the areas to activate the VMD function.
IMPORTANT•When the settings are being configured on the setup menu,...

[Status]
Select “On” or “Off” to determine whether or not to activate each VMD area.
• On:  Activates the respective VMD area.
• Off:  Inactivates the respective VMD area.
• Default:  Off
[Detection area]
Adjust the size of the VMD area using the slider. The smaller the selected value is, the higher the sensitivity
of VMD area becomes. The current value (1-10) will be displayed on the right of the slider.
• Default:  1
[Detection sensitivity]
Adjust the sensitivity of motion detection in the VMD area...

3.Click the [Set] button after completing the settings.
IMPORTANT
•The setting will not be applied unless the [Set] button is clicked.
4. To invalidate the VMD area, click the [Set] button after selecting “Off” for “Status” of the VMD area to be
invalidated.
→ The outline of the invalidated VMD area will turn to a dotted line. When the VMD area is invalidated,
no alarm will occur even when a motion can be recognized in the area.
5. To delete the VMD area, click the [Delete] button corresponding to the...

[E-mail notification]
Select “On” or “Off” to determine whether or not to provide notification by E-mail according to the settings for
the “Alarm” and “Diag.” checkboxes of “Destination of notification” below.
– When an alarm is detected (“Alarm”)
• Default:  Off
[Alarm image attachment]
Select “On” or “Off” to determine whether or not to attach an image to the E-mail to be sent when an alarm is
detected.
• Default:  Off
Note
•The settings for “Image capture size” of the “Alarm image” section on the...

The settings relating to Panasonic alarm protocol can be configured in this section.
Panasonic alarm protocol notification[Panasonic alarm protocol]
Select “On”  or “Off”  to determine whether or not to provide notification by Panasonic alarm protocol according
to the settings for the “Alarm” and “Diag.” checkboxes of “Destination of notification” below.
– When an alarm is detected (“Alarm”)
• Default:  Off
Note
•When  “On” is selected for  “Alarm”, notification of the alarm occurrence will be provided...

•Available range:  0-30
• Default:  2
Destination of notification [Address 1] - [Address 8]
Enter the destination IP address or host name of the Panasonic alarm protocol from the following. Up to 8
destination server addresses can be registered.
• [Alarm ] checkbox:  When the checkbox is selected, the Panasonic alarm notification will be provided upon
an alarm occurrence.
• [Destination server address]:  Enter the destination server address or host name.
– Available characters:  Alphanumeric characters,...