Panasonic Network Camera BL-VT164 BL-VP100 Owners Manual

•Off:  Images will be captured with the fixed gain level.
• Default:  On(High)
[Auto slow shutter]
The electronic sensitivity enhancement (sensitivity up) can be carried out by adjusting the storage time of the
sensor.
The following are available for the recording duration.
   :
Off(1/30s), Max.2/30s, Max.4/30s, Max.6/30s, Max.10/30s, Max.16/30s
:
Off(1/30s), Max.2/30s, Max.3/30s, Max.4/30s, Max.8/30s
• Default:  Off(1/30s)
IMPORTANT
•When “On” is selected for “Auto slow shutter”, frame rate may become...

Click the [Reset] button to reset the color to the default.
• Default:  128
[Blue gain]
Adjust the blue color of images.
When the cursor is moved in the “+” direction, the blue color will become thicker.
When the cursor is moved in the “–” direction, the blue color will be thinner.
Click the [Reset] button to reset the color to the default.
• Default:  128
[DNR]
The digital noise reduction function reduces noise automatically under the condition of low illuminance. Select
an effect level “High” or “Low”...

1.Display the “Image adjust” setup menu. ( ®page 57)
2. Click the [Start] button of “Mask area”.
→
 : Borders will appear and the image displayed on the [Image/Position] tab will be
divided into 48 (6x8).
→
 : Borders will appear and the image displayed on the [Image/Privacy] tab will be
divided into 48 (6x8).
→
: Borders will appear and the image displayed on the [Image/Privacy] tab will be divided into
48 (6x8) (16 (4x4)).
Operating Instructions63
9 Configure the settings relating to images and audio...

Note
:
• “Mask area ” can be set only when  “4:3” is selected for  “Aspect ratio ”. If the  “Aspect ratio ” is changed
to “16:9” after setting the mask area, the setting of the mask area is maintained.
3. Click the divided areas to be masked.
→ The clicked areas will be masked and will become white. To cancel masking, click the area again.
4.Click the [End] button after completing masking areas.
→
 : The borders on the image displayed on the [Image/Position] tab will disappear.
→
  : The borders on the...

A.Image in the aspect ratio of “16:9”
B. Areas where the image is not displayed when
“4:3” is selected for the aspect ratio
C. Image in the aspect ratio of “4:3” (Being cut
out from the aspect ratio of “16:9”)
:
• When “16:9” is selected for the aspect ratio of JPEG/H.264, the image will be displayed clipped from
the image of “4:3”. Therefore even when “16:9” is selected for “Image adjust”, the brightness of the
masked area will affect the image.
A. Image in the aspect ratio of “4:3”
B. Areas where the...

IMPORTANT•When the zoom factor is 1.5x or more, the setting of the preset positions will become unavailable.
Note
•Depending on the environment (such as when the temperature is below 5° C (41 °F), for example), the
moving speed of the camera to the preset position may become slower.
9.5.3.1  Register the preset positions 1.Select a preset position number.
→ The selected preset position number will be displayed in the “Position No” area.
When the selected number has already been registered, the camera...

3.To display the preset ID on the “Live” page, select “On” for “Preset ID” and enter the desired position title
to be displayed.
4. Click the [Set] button.
5. The settings for each item such as “Back light compensation (BLC)” can be configured for each position
independently. The settings for  “Back light compensation (BLC) ” and  “Mask area ” are updated immediately.
Note
•When registering the preset position, the camera direction may move slightly.
Position No [Preset ID]
Select  “On” or “Off”  to...

[Set] button
Registers the preset positions.
[Delete] button
Deletes the preset position specified by the position number.
[Close] button
Click this button to close the “Preset position” setup menu.
9.5.4  Adjust the angular field of view using the extra zoom function
(BL-VP104W/BL-VP104)
Click the [Setup>>] button of “Extra zoom” on the [Image/Privacy] tab of the “Image” page. ( ®page 57)
It is possible to adjust the angular field of view using the extra zoom function.
•: Click this button to adjust the...

•Depending on the panning/tilting direction (especially when the tilting degree is 45° - 90°) and the
zooming factor, the area set as the privacy zone may become visible. Make sure that each of the set
privacy zone is not visible after setting it.
Privacy zone
[Display type]
Select a display type of the privacy zone from the following.
• Gray:  The privacy zones will be displayed in gray.
• Off:  Does not display the privacy zones.
• Default:  Off
Zone setting [Zone select]
Click [
] of “Zone No” and...

Note•Set the privacy zone larger than the size of an object to be hidden.
• Panning, tilting and zooming operations can also be carried out on the [Image/Position] tab.
• When selecting “Zone No” after selecting “Gray” for “Display type”, a mask will be displayed at the
center of the image display area and will start blinking while changing its color as follows: Dark gray
®  Clear  ® Light gray
• When the other mask that had already been set is on the same zone, the mask that had previously
been set will...