Panasonic Network Camera BL-VT164 BL-VP100 Owners Manual

•Gray:  The privacy zones will be displayed in gray.
• Off:  Does not display the privacy zones.
• Default:  Off
Note
•Set the privacy zone larger than the size of an object to be hidden.
[Close] button
Click this button to close the “Privacy zone” setup menu.
Operating Instructions71
9 Configure the settings relating to images and audio [Image/Audio] (BL-VT164W/BL-VT164)/ Configure the settings relating to images [Image] (BL-VP104W/BL-VP104/BL-VP101) 

9.6  Configure the settings relating to audio [Audio]
(BL-VT164W/BL-VT164) Click the [Audio] tab on the “Image/Audio” page. ( ®page 34, page 35)
The settings relating to audio can be configured on this page.
Note
•Images and audio will not be synchronized. Therefore, images and audio may not always match.
• Audio may be interrupted depending on the network environment.
[Audio transmission/reception]
Select the communication mode used for audio data transmission/reception between the camera and the PC...

Note•G.711 is available only when “Mic input” is selected for “Audio transmission/reception”.
[Audio bit rate]
Select “16kbps” or “32kbps” for the audio bit rate used to transmit/receive audio data.
• Default:  32kbps
Note
•When selecting a smaller value for “Bandwidth control(bit rate)” ( ®page 104) while putting a priority
on the JPEG/H.264 image transmission, select “16kbps” for “Audio bit rate”.
• [Audio bit rate] is unavailable when “G.711” is selected for “Audio encoding format”.
[Mic input volume...

[Audio output port (PC to Camera)]
Enter the transmission port number (the port number on the camera used to receive audio data transmitted
from the PC).
• Available port number:  1024-50000 (Only even numbers are available.)
• Default:  34004
Note
•The transmission port number entered for “Audio output port (PC to Camera)” will be used only when
“Unicast port (MANUAL)” is selected for “Transmission type” ( ®page 49).
When “Off” is selected for “H.264 transmission” ( ®page 49) or when “Unicast port...

10   Configure the multi-screen settings
[Multi-screen]
The cameras from which images are to be displayed on a multi-screen can be registered on the
“Multi-screen” page. ( ®page 34, page 35)
[IP address]
Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be
registered as a group and up to 4 groups (16 cameras) can be registered.
When the HTTP port number for the camera of which images are to be displayed had been changed, enter as
follows:
Example of...

–Example when entering an IPv4 address:  http://192.168.0.10:8080
– Example when entering an IPv6 address:  http://[2001:db8:0:0:0:0:0:1]:8080
To access the cameras using the HTTPS protocol, enter as follows:
Example of entry:  https://192.168.0.10/
• Available number of characters:  1 - 128 characters
• Default:  (Cam. 1) selfcamera, (Cam. 2-16) not registered
IMPORTANT
•When accessing the camera using the HTTPS protocol, install the security certificate of the camera to
display images on the monitor. (...

11   Configure the alarm settings [Alarm]The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the
VMD area settings, and the alarm occurrence notification can be configured on this page.
The “Alarm” page has 3 tabs; the [Alarm] tab, the [VMD area] tab and the [Notification] tab.
11.1  Configure the settings relating to the alarm
action [Alarm] Click the [Alarm] tab on the “Alarm” page. ( ®page 34, page 35)
The settings relating to the alarm can be...

[Terminal 3]  
Determine how to use terminal 3.
• Off:  Not used.
• Alarm input:  Receives alarms.
– Close:  An alarm is detected when the terminal status is changed to “On”.
– Open:  An alarm is detected when the terminal status is changed to “Off”.
• AUX output:  AUX output will be supplied. The [AUX] buttons will be displayed on the “Live” page.
• Default:  Off
Note
•AUX is a camera terminal that allows users to operate (Open/Close) arbitrarily from the “Live” page.
For example, an operator can...

[Originating port number]
Select a port number to be used to receive the command alarm.
• Available range:  1-65535
• Default:  8181
The following port numbers are unavailable since they are already in use.
20, 21, 23, 25, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 554, 995, 10669, 10670, 59000-61000
11.2  Configure the settings relating to the camera
action on alarm occurrence [Alarm] (BL-VT164W/
BL-VT164) Click the [Alarm] tab on the “Alarm” page. ( ®page 34, page 35)
The settings relating to the...

[Body heat sensor]
Select an action to be taken when a body heat sensor is detected from the following.
• Off:  Does not take any action even when a body heat sensor is detected.
• 1-64:  When the registered preset position is selected, the camera will move to the selected preset position
when a body heat sensor is detected.
• Default:  Off
[VMD alarm]
Select an action to be taken when a VMD alarm is detected from the following.
• Off:  Does not take any action even when a VMD alarm is detected.
• 1-64:...