Panasonic Multi Function Controller Aw Rp605 Operating Instructions

							31
Operation
$Tracing memory settings
The multi-function controller is equipped with a tracing
memory function for entering the series of settings with
which pan-tilt head systems is operated.
The tracing memories are entered into TRACING/PRESET
MEMORY buttons 1 through 10.
1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2.Press the MENU button, and turn the menu setting
control (main), and set it so that the CONTROLLER
SETTING item appears at the top of the LCD panel.
3. Press the OK button.
The following item appears on the LCD panel.
4. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
5. Set the tracing memory entry time (memory length) and
number of memories using the menu setting control (R).
30s :30 seconds a10 memories
(buttons 1 through 10)
60s :60 seconds a5 memories
(buttons 1 through 5)
150s :150 seconds a2 memories
(buttons 1 and 2)
300s :300 seconds a1 memory
(button 1)
 
OIf data has already been entered into a tracing
memory, the entry time and number of memories
cannot be set.  Before entering different settings,
delete the contents of the tracing memory, and then
proceed.
OOnce entry times and numbers of memories have
been set, the settings cannot be changed for any of
the buttons unless memories are deleted .M ME
EM
MO
OR
RY
Y 
 L
LE
EN
NG
GT
TH
H 
 S
SE
EL
LE
EC
CT
T
3 30
00
0s
s
M ME
EM
MO
OR
RY
Y 
 L
LE
EN
NG
GT
TH
H 
 S
SE
EL
LE
EC
CT
T
1 15
50
0s
s
M ME
EM
MO
OR
RY
Y 
 L
LE
EN
NG
GT
TH
H 
 S
SE
EL
LE
EC
CT
T
6 60
0s
s
M ME
EM
MO
OR
RY
Y 
 L
LE
EN
NG
GT
TH
H 
 S
SE
EL
LE
EC
CT
T
3 30
0s
s
M ME
EM
MO
OR
RY
Y 
 L
LE
EN
NG
GT
TH
H 
 S
SE
EL
LE
EC
CT
T
3 30
0s
s
S SI
IG
GN
NA
AL
L 
 S
SE
EL
LE
EC
CT
T
C C.
.V
VI
ID
DE
EO
O 
 
nC C.
.V
VI
ID
DE
EO
O
C CO
ON
NT
TR
RO
OL
LL
LE
ER
R 
 S
SE
ET
TT
TI
IN
NG
G
nO OK
K 
 K
Ke
ey
y
Setting the entry time (memory length) and number
of memories
CONTROL/PREVIEW MONITOR OUT SELAUX 12345TALLY TRACING MEMORY
LAMP
MENU
LIMIT
OFF LIMIT
ONFULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT R/B
GAIN/PED WHITE
BALAW C
GAIN
MODE
CLOSEWIDE NEAR
DATA  S E T
TR/PSET M.LOCK
MEMORY
IRIS IRIS
IRISOPENZOOMTELEFOCUS
FA R
CALL INCOM
LEVEL
FOCUS
OPEN
FA R TELE
OFFON OPERATE
WIDE
ZOOM/FOCUS/IRISABC
AT W
A
BNG
OKSTART/STOP RESTORE RESET DEF WIP H/F EXT ND
OPTIONPAN/TILT SETCAMERA CONTROL
TRACING/PRESET MEMORY
IRIS SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
12345678910
11121314151617181920
212223242526272829130
31323334353637383940
41424344454647484950DOWNPAN/TILT/FOCUS/IRISUP
LRCLOSE
NEAROPEN
FA RCLOSE
NEAR
252•431
6.Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue setting the entry times and number of
memories for each system concerned. 
						

							328. The entry in the tracing memory commences as soon as
the pan, tilt, zoom, focus, iris or white balance mode
selection is initiated so proceed with the entry operation.
The START/STOP button stops flashing and comes on,
and the lamps of TRACING/PRESET MEMORY buttons
11 through 30 come on to provide a general guideline of
the time for which data can be entered.
Each of the No. 11 through No. 20 buttons indicates a
time of approximately 3 seconds; and each of the No. 21
through No. 30 buttons indicates a time of approximately
30 seconds.
The lamps of buttons No. 20 and above go off
approximately every 3 seconds to indicate the remaining
time during which data can be entered in the memories.
As soon as the lamp in button No. 11 goes off, the
buzzer sounds, and the tracing memory entry is
completed.

OPress the START/STOP button to suspend the
tracing memory entry at any time.  The operations
performed up until the entry was stopped are entered
as the tracing memory data.
OThe buzzer sounds when tracing memory entry is
started or suspended and when data entry is
completed.
9.If necessary, enter the other operations into
TRACING/PRESET MEMORY buttons 1 through 10 as
tracing memory data.
10.Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue setting the tracing memory data for each
system concerned.
Operation
1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Use the following buttons to establish the modes.
OPress the IRIS button to establish the MANU mode
(the IRIS button’s lamp now goes off).
If the AUTO mode is established, the lens iris position
will not be entered.
OPress the TR/PSET button to establish the tracing
memory mode (the TR/PSET button’s lamp now
comes on).
OIf the M.LOCK button’s lamp lights, press the
M.LOCK button to establish the memory entry mode
(the M.LOCK button’s lamp now goes off).
3.Operate the ZOOM lever and PAN/TILT lever, and on
the monitor now check the pictures which are to be shot.
4. Select the white balance from among the A, B and ATW
buttons, and adjust the lens iris using the FOCUS/IRIS
dial.
5. Press the START POINT button.
The lamps of those buttons among TRACING/PRESET
MEMORY buttons 1 through 10 in which data can be
entered now come on.

If any button’s lamp remains off, it means that data has
already been entered into that button.  To enter data into
a button whose lamp is off, delete the data in the
memory first, and then proceed.
6. Press the button into which data is to be entered.
Only the lamp of the button which was pressed comes
on, and the data is entered as the start position of the
tracing memory.

If the PAN/TILT lever is now operated, the entry mode
will be canceled.
7. Press the START/STOP button.
The START/STOP button’s lamp flashes, and the entry
standby mode is established.

When the START/STOP button is now pressed, the
entry mode will be canceled. Entering the tracing memory data
CONTROL/PREVIEW MONITOR OUT SELAUX 12345TALLY TRACING MEMORY
LAMP
MENU
LIMIT
OFF LIMIT
ONFULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT R/B
GAIN/PED WHITE
BALAW C
GAIN
MODE
CLOSEWIDE NEAR
DATA  S E T
TR/PSET M.LOCK
MEMORY
IRIS IRIS
IRISOPENZOOMTELEFOCUS
FA R
CALL INCOM
LEVEL
FOCUS
OPEN
FA R TELE
OFFON OPERATE
WIDE
ZOOM/FOCUS/IRISABC
AT W
A
BNG
OKSTART/STOP RESTORE RESET DEF WIP H/F EXT ND
OPTIONPAN/TILT SETCAMERA CONTROL
TRACING/PRESET MEMORY
IRIS SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
12345678910
11121314151617181920
212223242526272829130
31323334353637383940
41424344454647484950DOWNPAN/TILT/FOCUS/IRISUP
LRCLOSE
NEAROPEN
FA RCLOSE
NEAR
2433(4)225•7164
Example of remaining time display
: Indicates that a button’s lamp is lighted.
12345678910
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 3045 seconds
12345678910
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 3021 seconds
When data has been entered into the tracing memories,
the data will also be saved in the pan-tilt head’s
memories.  Therefore, when the pan-tilt head has been
replaced with another head, enter the data into the tracing
memories of the head now in use. 
						

							33 1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Press the button in which the tracing memory data to be
recalled has been entered.
The pan-tilt head system is set to the start position
entered in the tracing memory.
3. After the pan-tilt head system has been set to the tracing
memory start position status and then stopped, press the
button in which the tracing memory data has been
entered again .
The pan-tilt head system now starts the operations
entered in the tracing memory.
 
OWhen the AW-PH350 is used as the pan-tilt head, no
operations will be acknowledged even if the button in
which the tracing memory data has been entered is
pressed before the head is set to the start position
status.
If, when a model other than the AW-PH350 is used as
the pan-tilt head, the button in which the tracing
memory data has been entered is pressed before the
head is set to the start position status, the operations
of the series of settings stored in the memory will be
performed again from the position where the button
was pressed.
Therefore, the button in which the tracing memory
data has been entered must be pressed after the pan-
tilt head system has been set to the tracing memory
start position status and stopped.
OPress the START/STOP button to suspend the recall
of the data from tracing memory at any time.
This recall can also be suspended as soon as the
pan, tilt, zoom or focus operation has been initiated.
OThe buzzer sounds when tracing memory data recall
is started or suspended and when the data recall is
completed. Recalling tracing memory data
1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Press the button in which the tracing memory data to be
changed has been entered, and call the start position of
the tracing memory.
3. Press the RESTORE button.
The RESTORE button’s lamp flashes, and the start
position setting of the tracing memory can be changed.

The change mode is canceled if the START/STOP
button is pressed at this point.
4. Press the RESTORE button again.
The pan-tilt head system starts performing the
operations entered in the tracing memory, and the
RESTORE button’s lamp stops flashing and comes on.
As with the data entry process, buttons No. 11 through
No. 30 serve as a general guideline for the time.
5. The tracing memory operations are changed.

Partial changes cannot be made to tracing memory
operations.  Enter all the operations again starting from
the point where the change is made.
6.As soon as the lamp in button No. 11 goes off, the
buzzer sounds, and the tracing memory change is
completed. Making changes to the tracing memory
Operation
CONTROL/PREVIEW MONITOR OUT SELAUX 12345TALLY TRACING MEMORY
LAMP
MENU
LIMIT
OFF LIMIT
ONFULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT R/B
GAIN/PED WHITE
BALAW C
GAIN
MODE
CLOSEWIDE NEAR
DATA  S E T
TR/PSET M.LOCK
MEMORY
IRIS IRIS
IRISOPENZOOMTELEFOCUS
FA R
CALL INCOM
LEVEL
FOCUS
OPEN
FA R TELE
OFFON OPERATE
WIDE
ZOOM/FOCUS/IRISABC
AT W
A
BNG
OKSTART/STOP RESTORE RESET DEF WIP H/F EXT ND
OPTIONPAN/TILT SETCAMERA CONTROL
TRACING/PRESET MEMORY
IRIS SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
12345678910
11121314151617181920
212223242526272829130
31323334353637383940
41424344454647484950DOWNPAN/TILT/FOCUS/IRISUP
LRCLOSE
NEAROPEN
FA RCLOSE
NEAR
START/STOP
12
CONTROL/PREVIEW MONITOR OUT SELAUX 12345TALLY TRACING MEMORY
LAMP
MENU
LIMIT
OFF LIMIT
ONFULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT R/B
GAIN/PED WHITE
BALAW C
GAIN
MODE
CLOSEWIDE NEAR
DATA  S E T
TR/PSET M.LOCK
MEMORY
IRIS IRIS
IRISOPENZOOMTELEFOCUS
FA R
CALL INCOM
LEVEL
FOCUS
OPEN
FA R TELE
OFFON OPERATE
WIDE
ZOOM/FOCUS/IRISABC
AT W
A
BNG
OKSTART/STOP RESTORE RESET DEF WIP H/F EXT ND
OPTIONPAN/TILT SETCAMERA CONTROL
TRACING/PRESET MEMORY
IRIS SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AU TO
MANU
LOCK
12345678910
11121314151617181920
212223242526272829130
31323334353637383940
41424344454647484950DOWNPAN/TILT/FOCUS/IRISUP
LRCLOSE
NEAROPEN
FA RCLOSE
NEAR
123•4 
						

							34 1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2.While holding down the RESET button, press the
buttons in which the tracing memory data to be deleted
has been entered.

The lamps of the buttons in which tracing memory data
has been entered (TRACING/PRESET MEMORY
buttons 1 through 10) come on when the RESET button
is pressed.
3. The buttons’ lamps go off, and the tracing memory data
is deleted.

Data cannot be deleted while the M.LOCK button’s lamp
is lighted. Deleting tracing memory data
Operation
CONTROL/PREVIEW MONITOR OUT SELAUX 12345TALLY TRACING MEMORY
LAMP
MENU
LIMIT
OFF LIMIT
ONFULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT R/B
GAIN/PED WHITE
BALAW C
GAIN
MODE
CLOSEWIDE NEAR
DATA  S E T
TR/PSET M.LOCK
MEMORY
IRIS IRIS
IRISOPENZOOMTELEFOCUS
FA R
CALL INCOM
LEVEL
FOCUS
OPEN
FA R TELE
OFFON OPERATE
WIDE
ZOOM/FOCUS/IRISABC
AT W
A
BNG
OKSTART/STOP RESTORE RESET DEF WIP H/F EXT ND
OPTIONPAN/TILT SETCAMERA CONTROL
TRACING/PRESET MEMORY
IRIS SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
12345678910
11121314151617181920
212223242526272829130
31323334353637383940
41424344454647484950DOWNPAN/TILT/FOCUS/IRISUP
LRCLOSE
NEAROPEN
FA RCLOSE
NEAR
1
2M. LOCK 
						

							35
Operation
$Preset memory settings
The multi-function controller is equipped with a preset
memory function for entering the positions and settings with
which the pan-tilt head system is to shoot.
Preset memory data is entered into TRACING/PRESET
MEMORY buttons 1 through 50.
1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Connect a color monitor to the VIDEO/Y OUT connector
on the main unit that corresponds to the pan-tilt head
system currently selected.
3. Use the following buttons to establish the modes.
OPress the IRIS button to establish the MANU mode
(the IRIS button’s lamp now goes off).
If the AUTO mode is established, the lens iris position
will not be entered.
OPress the TR/PSET button to establish the preset
memory mode (the TR/PSET button’s lamp now goes
off).
OIf the M.LOCK button’s lamp lights, press the
M.LOCK button to establish the memory entry mode
(the M.LOCK button’s lamp now goes off).
4.Operate the ZOOM lever and PAN/TILT lever, and on
the monitor check the pictures which are to be shot.
5. Select the white balance from among the A, B and ATW
buttons, and adjust the lens iris using the FOCUS/IRIS
dial.
6. Set the unit to a state in which the MEMORY button is
held down.
When the MEMORY button is pressed, those buttons
among the TRACING/PRESET MEMORY buttons 1
through 50 in which data can be entered start flashing in
sequence.

If a button has a lamp that remains off, it means that
data has already been entered into it.  Preset memory
data cannot be entered into it.
7.While the MEMORY button is held down, press the
button in which the preset memory data is to be entered.
8. If necessary, enter other shooting positions and settings
into other buttons among TRACING/PRESET MEMORY
buttons 1 through 50 as preset memory data.
9.Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue setting the preset memory data for each system
concerned. Entering preset memory data
CONTROL/PREVIEW MONITOR OUT SELAUX 12345TALLY TRACING MEMORY
LAMP
MENU
LIMIT
OFF LIMIT
ONFULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT R/B
GAIN/PED WHITE
BALAW C
GAIN
MODE
CLOSEWIDE NEAR
DATA  S E T
TR/PSET M.LOCK
MEMORY
IRIS IRIS
IRISOPENZOOMTELEFOCUS
FA R
CALL INCOM
LEVEL
FOCUS
OPEN
FA R TELE
OFFON OPERATE
WIDE
ZOOM/FOCUS/IRISABC
AT W
A
BNG
OKSTART/STOP RESTORE RESET DEF WIP H/F EXT ND
OPTIONPAN/TILT SETCAMERA CONTROL
TRACING/PRESET MEMORY
IRIS SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
12345678910
11121314151617181920
212223242526272829130
31323334353637383940
41424344454647484950DOWNPAN/TILT/FOCUS/IRISUP
LRCLOSE
NEAROPEN
FA RCLOSE
NEAR
3544(5)3315
6•7 
						

							G/L SETTING
CABLE LENGTH [SHORT]
H PHASE [± 0]
SC PHASE [COARSE: 1, FINE: ± 0]
CABLE COMP
CABLE COMP AUTO
CABLE COMP MANUAL (Y, C)
CABLE COMP MANUAL (Y Level)CABLE COMP MANUAL (f Response)
CONTROLLER SETTING
SIGNAL SELECT [C. VIDEO5C. VIDEO]
BUZZER SET [ON]
EXT CONTROL OUT [OFF]COMPONENT [Y/Pr/Pb] 4 [PAL OUTPUT SIGNAL]MEMORY LENGTH [30s]HEAD SW (R) FUNCTION [OFF]VIRTUAL STUDIO MODE [OFF]
P/T SETTING
PAN DIRECTION [NORMAL]
TILT DIRECTION [NORMAL]
ZOOM DIRECTION [NORMAL]
IRIS DIRECTION [NORMAL]FOCUS DIRECTION [NORMAL]
SPEED SELECT (PAN) [HIGH: FAST, LOW: FAST]SPEED SELECT (TILT) [HIGH: FAST, LOW: FAST]SPEED SELECT (ZOOM) [HIGH: FAST, LOW: FAST]SPEED SELECT (FOCUS) [HIGH: FAST, LOW: FAST]SPEED WITH ZOOM POS. [OFF]DIAGONAL MOTION [OFF]DIAGONAL SPEED [30]
J
J
J
J
J
With the COARSE setting, it is not possible to switch the speed
at which the setting value changes when the jog dial is pressed.
36
Setting menus

OThe factory settings are indicated in parentheses.
OIt is possible to switch the speed at which the setting value of the items marked with Jchanges each time the jog dial is pressed.
Note that this function may not work with the AW-RP615 Control Panel (optional accessory).
The COMPONENT item appears when an RGB card (AW-PB302)
has been installed in the OPTION CARD slot. 
						

							
OThe factory settings are indicated in parentheses.
OThe setting values for items in parentheses with marked with an asterisk (§) are based on the AW-E800A being used as the camera.
When a camera other than the AW-E800A is to be used, change the setting to the initial setting of that camera.
OIt is possible to switch the speed at which the setting value of the items marked with Jchanges each time the jog dial is pressed.
Note that this function may not work with the AW-RP615 Control Panel (optional accessory).
37
Setting menus
SCENE [USER]
SHUTTER [OFF]
DETAIL [HIGH]
S/S FREQUENCY [60.34 Hz]CHROMA LEVEL [± 0]HIGH LIGHT CHROMA [OFF]COLOR BAR SET [7.5 IRE] [PAL ---]DETAIL FLESH TONE [MID] [PAL FLESH DETAIL LEVEL]NEGA/POSI [POSI]CLEAN DNR [OFF]ASPECT RATIO [16:9]FAN [ON]ATW SPEED [MIDDLE]FIELD/FRAME [FIELD]2D LPF [OFF]H DETAIL LEVEL H [+24] §V DETAIL LEVEL H [+7]   §H DETAIL LEVEL L [+12] §V DETAIL LEVEL L [+4]   §DETAIL BAND [5]     §NOISE SUPPRESS [0]LEVEL DEPENDENT [0%]DARK DETAIL [0]CHROMA DETAIL [0]CORNER DETAIL [OFF]PRECISION DETAIL [OFF]MATRIX (R-G) [± 0]MATRIX (R-B) [± 0]MATRIX (G-R) [± 0]MATRIX (G-B) [± 0]MATRIX (B-R) [± 0]MATRIX (B-G) [± 0]GAMMA [0.45]KNEE POINT [88%]WHITE CLIP [110%]FLARE R [0]FLARE G [0]FLARE B [0]BLACK STRETCH [OFF]ZEBRA INDICATOR [OFF]ZEBRA L LEVEL [70%]ZEBRA H LEVEL [85%]SAFETY ZONE [1]EVF OUTPUT [Y]COMPONENT [Y/Pr/Pb] [PAL OUTPUT SIGNAL]CHARGE TIME [AUTO]AGC MAX LEVEL [18 dB]
PICTURE LEVEL [± 0] [PAL AUTO IRIS LEVEL]LIGHT PEAK/AVG [0] [PAL AUTO IRIS PEAK/AVG]LIGHT AREA [TOP CUT] [PAL AUTO IRIS AREA]
USER
CAMERA SETTING
SHUTTER [OFF]
DETAIL [HIGH]
S/S FREQUENCY [60.34 Hz]CHROMA LEVEL [± 0]HIGH LIGHT CHROMA [OFF]COLOR BAR SET [7.5 IRE] [PAL---]DETAIL FLESH TONE [MID] [PAL FLESH DETAIL LEVEL]NEGA/POSI [POSI]CLEAN DNR [OFF]ASPECT RATIO [16:9]FAN [ON]ATW SPEED [MIDDLE]CONTRAST (GAMMA) [MID]FLESH TONE [± 0]DETAIL SELECT [NORMAL]NOISE SUPPRESS [OFF]V RESOLUTION [NORMAL]ZEBRA INDICATOR [OFF]ZEBRA L LEVEL [70%]ZEBRA H LEVEL [85%]SAFETY ZONE [1]EVF OUTPUT [Y]COMPONENT [Y/Pr/Pb] [PAL OUTPUT SIGNAL]CHARGE TIME [AUTO]AGC MAX LEVEL [18 dB]
PICTURE LEVEL [± 0] [PAL AUTO IRIS LEVEL]LIGHT PEAK/AVG [0] [PAL AUTO IRIS PEAK/AVG]LIGHT AREA [TOP CUT] [PAL AUTO IRIS AREA]
HALOGEN
SHUTTER [OFF]
DETAIL [HIGH]
S/S FREQUENCY [60.34 Hz]CHROMA LEVEL [± 0]HIGH LIGHT CHROMA [OFF]COLOR BAR SET [7.5 IRE] [PAL---]DETAIL FLESH TONE [MID] [PAL FLESH DETAIL LEVEL]NEGA/POSI [POSI]CLEAN DNR [OFF]ASPECT RATIO [16:9]FAN [ON]ATW SPEED [MIDDLE]CONTRAST (GAMMA) [MID]FLESH TONE [± 0]DETAIL SELECT [NORMAL]NOISE SUPPRESS [OFF]V RESOLUTION [NORMAL]ZEBRA INDICATOR [OFF]ZEBRA L LEVEL [70%]ZEBRA H LEVEL [85%]SAFETY ZONE [1]EVF OUTPUT [Y]COMPONENT [Y/Pr/Pb] [PAL OUTPUT SIGNAL]CHARGE TIME [AUTO]AGC MAX LEVEL [18 dB]
PICTURE LEVEL [± 0] [PAL AUTO IRIS LEVEL]LIGHT PEAK/AVG [0] [PAL AUTO IRIS PEAK/AVG]LIGHT AREA [TOP CUT] [PAL AUTO IRIS AREA]
FLOURECENT
SHUTTER [OFF]
DETAIL [HIGH]
S/S FREQUENCY [60.34 Hz]CHROMA LEVEL [± 0]HIGH LIGHT CHROMA [OFF]COLOR BAR SET [7.5 IRE] [PALDETAIL FLESH TONE [MID] [PAL FLNEGA/POSI [POSI]CLEAN DNR [OFF]ASPECT RATIO [16:9]FAN [ON]ATW SPEED [MIDDLE]CONTRAST (GAMMA) [MID]FLESH TONE [± 0]DETAIL SELECT [NORMAL]NOISE SUPPRESS [OFF]V RESOLUTION [NORMAL]ZEBRA INDICATOR [OFF]ZEBRA L LEVEL [70%]ZEBRA H LEVEL [85%]SAFETY ZONE [1]EVF OUTPUT [Y]COMPONENT [Y/Pr/Pb] [PALCHARGE TIME [AUTO]AGC MAX LEVEL [18 dB]
PICTURE LEVEL [± 0] [PAL AUTLIGHT PEAK/AVG [0] [PAL AUTOLIGHT AREA [TOP CUT] [PA
OUTDOOR
JJ
J
J J
J
J
J
J
J
J
J
J
J
JJ
J
JJ
J
J 
						

							38
Setting menus
CABLE LENGTH (SHORT, LONG)
This item sets the compensation for the length of the BNC
cable used for the genlock signals.  “SHORT” is set when
the cable is less than 500 meters long; “LONG” is set when
it is 500 meters or longer.
H PHASE (–206 to +49)
This item is used to adjust the horizontal phase during
genlock.
SC PHASE (1, 2, 3, 4, –511 to +511)
This item is used to adjust the color phase during genlock.
CABLE COMP AUTO
When this item is selected and the OK button is pressed,
the cable compensation is adjusted automatically.
Perform these operations to achieve a simple adjustment or
when a waveform monitor, vectorscope or other such
measuring instrument is not available.
CABLE COMP MANUAL (Y: 0 to 255; C: 0 to 255)
Select this item to adjust the cable compensation manually
when C.VIDEO has been selected as the input signal setting
for the SIGNAL SELECT item on the CONTROLLER
SETTING menu.
CABLE COMP MANUAL Y LEVEL (0 to 255)
Select this item to adjust the cable compensation manually
when Y/Pr/Pb has been selected as the input signal setting
for the SIGNAL SELECT item on the CONTROLLER
SETTING menu.
When it is selected, the multi-function controller’s video
output signals are automatically set to Y/Pr/Pb.  When it is
released, the original video output signals are restored.
CABLE COMP MANUAL f Response (0 to 255)
Select this item to adjust the compensation for the
frequency response manually when Y/Pr/Pb has been
selected as the input signal setting for the SIGNAL SELECT
item on the CONTROLLER SETTING menu.
When it is selected, the output signals from the camera are
automatically set to Y/C, and the multi-function controller’s
video output signals are set to Y/Pr/Pb.  The frequency
response is compensated by adjusting the burst level using
the Pr output signal.  When this item is released, the original
video output signals are restored.
CABLE COMP (cable compensation)
menu
G/L SETTING (genlock adjustment)
menu
SIGNAL SELECT 
(C.VIDEO5C.VIDEO, Y/Pr/Pb5C.VIDEO, Y/Pr/Pb5Y/Pr/Pb)
This is used to set the multi-function controller’s input
signals and output signals.
When the signals supplied to the multi-function controller
have been set to C.VIDEO (composite signals), the output
signals signals are fixed to the C.VIDEO as well.
When the signals supplied to the multi-function controller
have been set to Y/Pr/Pb (component signals), either the
Y/Pr/Pb or C.VIDEO signals can be selected as the output
signals.
BUZZER SET (ON/OFF)
This is used to set the buzzer contained inside the control
panel to ON or OFF.  The buzzer does not sound when OFF
is selected as this item’s setting.
At the ON setting, the buzzer sounds when the CALL button
is pressed and when a tracing memory operation (entry,
recall or change) has been started, suspended or data entry
has been completed.
EXT CONTROL OUT (ON/OFF)
When ON is selected as this item’s setting, the pan-tilt head
system’s control signals are output from the EXTERNAL
CONTROL OUT connector used for additional functions.
Since it is not supported at the present time, select the OFF
setting for use.
COMPONENT (RGB, Y/Pr/Pb, Y/C)
This item is used to select the video signals which are to be
output when the RGB card (AW-PB302) has been installed
in the OPTION CARD slot.
MEMORY LENGTH (30s, 60s, 150s, 300s)
This item is used to set the tracing memory entry time
(memory length) and number of memories.
30s :30 seconds a10 memories
60s :60 seconds a5 memories
150s :150 seconds a2 memories
300s :300 seconds a1 memory

If data has already been entered into a tracing memory, the
entry time and number of memories cannot be set.  Before
entering different settings, delete the contents of the tracing
memory.
HEAD SW (R) FUNCTION (ON/OFF)
When ON is selected as this item’s setting, it is no longer
possible to switch the adjustment dial functions (IRIS and
FOCUS) using the button on the top surface of the
PAN/TILT lever.
Since it is not supported at the present time, select the OFF
setting for use.
VIRTUAL STUDIO MODE (ON/OFF)
When ON is selected as this item’s setting, the camera’s
video signals are switched to the corrected color position for
using the blue background of the virtual studio.
CONTROLLER SETTING (controller
setting) menu 
						

							39
Setting menus
PAN DIRECTION (NORMAL/REVERSE)
This item is used to select the operations in the horizontal
direction of the pan-tilt head system which are to be
performed by operating the PAN/TILT lever.
When NORMAL is selected as the setting, the pan-tilt head
system moves toward the left when the PAN/TILT lever is
tilted toward the L side, and it moves toward the right when
it is tilted toward the R side.
Conversely, when REVERSE is selected as the setting, the
pan-tilt head system moves in the reverse directions.

Always select REVERSE as the setting when using the AW-
PH300 as the pan-tilt head system in the stand-alone
installation.  In this case, when REVERSE is selected as the
setting, the pan-tilt head system moves toward the left when
the PAN/TILT lever is tilted toward the L side, and it moves
toward the right when it is tilted toward the R side.
Conversely, when NORMAL is selected as the setting, the
pan-tilt head system moves in the reverse directions.
TILT DIRECTION (NORMAL/REVERSE)
This item is used to select the operations for the vertical
direction of the pan-tilt head system which are to be
performed by manipulating the PAN/TILT lever.
When NORMAL is selected, the pan-tilt head system moves
upward when the PAN/TILT lever is tilted toward the UP
side, and it moves downward when it is tilted toward the
DOWN side.
Conversely, when REVERSE is selected, the pan-tilt head
system moves in the reverse directions.

Always select REVERSE as the setting when using the AW-
PH300 as the pan-tilt head system for suspended
installation.  In this case, when REVERSE is selected, the
pan-tilt head system moves upward when the PAN/TILT
lever is tilted toward the UP side, and it moves downward
when it is tilted toward the DOWN side.  Conversely, when
NORMAL is selected, the pan-tilt head system moves in the
reverse directions.
ZOOM DIRECTION (NORMAL/REVERSE)
This item is used to select the zoom movements of the lens
which are to be performed by operating the ZOOM lever.
When NORMAL is selected as the setting, the zoom moves
toward the telephoto side when the ZOOM lever is tilted
toward the TELE side, and it moves toward the wide-angle
side when it is tilted toward the WIDE side.
Conversely, when REVERSE is selected as the setting, the
zoom moves in the reverse directions.
FOCUS DIRECTION (NORMAL/REVERSE)
This item is used to select the focus operations of the lens
which are to be performed by operating the dials on the top
of the PAN/TILT lever and ZOOM lever.
When NORMAL is selected, the focus moves toward the far-
distance side when the dial is turned toward the FAR side,
and it moves toward the near-distance side when it is turned
toward the NEAR side.
Conversely, when REVERSE is selected as the setting, the
focus moves in the reverse directions.
P/T SETTING (pan-tilt head setting)
menu
IRIS DIRECTION (NORMAL/REVERSE)
This item is used to select the focus operations of the lens
which are to be performed by operating the dials on the top
of the PAN/TILT lever and ZOOM lever.
When NORMAL is selected for the setting, turn the dial
towards OPEN to open up the iris and towards CLOSE to
close in the iris.
Conversely, when REVERSE is selected as the setting, the
iris moves in the reverse directions.
As the focusing of some lenses moves in reverse, select the
setting which best suits the operator.
SPEED SELECT (PAN)
(HIGH: SLOW/MID/FAST; LOW: SLOW/MID/FAST)
This item is used to select the speed at which the pan-tilt
head system is to operate in the horizontal direction in
response to operation of the PAN/TILT lever.
The speed can be set to SLOW, MID or FAST for the HIGH
mode and also for the LOW mode which are switched using
the SPEED button.

When 1 or 2 has been selected as the SPEED WITH ZOOM
POS. item setting, switching between SLOW, MID and
FAST is not possible.
SPEED SELECT (TILT) 
(HIGH: SLOW/MID/FAST; LOW: SLOW/MID/FAST)
This item is used to select the speed at which the pan-tilt
head system is to operate in the vertical direction in
response to operation of the PAN/TILT lever.
The speed can be set to SLOW, MID or FAST for the HIGH
mode and also for the LOW mode  which are switched using
the SPEED button.

When 1 or 2 has been selected as the SPEED WITH ZOOM
POS. item setting, switching between SLOW, MID and
FAST is not possible.
SPEED SELECT (ZOOM) 
(HIGH: SLOW/MID/FAST; LOW: SLOW/MID/FAST)
This item is used to select the speed at which the lens is to
perform zoom operations in response to operation of the
ZOOM lever.
The speed can be set to SLOW, MID or FAST for the HIGH
mode and also for the LOW mode  which are switched using
the SPEED button.
SPEED SELECT (FOCUS) 
(HIGH: SLOW/MID/FAST; LOW: SLOW/MID/FAST)
This item is used to select the speed at which the lens is to
perform the focusing operations in response to operation of
the dials on the top of the PAN/TILT lever and ZOOM lever.
The speed can be set to SLOW, MID or FAST for the HIGH
mode and also for the LOW mode  which are switched using
the SPEED button. 
						

							40
Setting menus
SPEED WITH ZOOM POS. (OFF, 1, 2)
When 1 or 2 is selected as this item’s setting, the pan-tilt
operation of the pan-tilt head system is slowed down so that
the pan-tilt position will be more easily aligned when the
lens zoom is at the wide-angle position.
DIAGONAL MOTION (ON/OFF)
OFF : The pan-tilt head system moves to the position set in
the preset memory at maximum speed.
ON : The speed at which the pan-tilt head system moves
is adjusted so that it will move to the position set in
the preset memory in a straight line.
However, repeatability with the AW-PH350 pan-tilt
head will be ±10´, resulting in lower stopping
accuracy.
DIAGONAL SPEED (1 to 30)
This item is used to select the speed at which the pan-tilt
head system is to operate when DIAGONAL MOTION item
has been set to ON.  The higher the value set, the faster the
speed at which the pan-tilt head will operate.
When DIAGONAL MOTION item has been set to OFF,
operational speed cannot be set.The operation items differ depending on the type of camera
or pan-tilt head used and the optional card installed.
For further details, refer to the operating instructions of the
camera used.CAMERA SETTING menu

The DIAGONAL MOTION and DIAGONAL SPEED items
appear when the AW-PH350 is used as the pan-tilt head.