Panasonic Multi Function Controller Aw Rp605 Operating Instructions

Model AW- P
Before attempting to connect, operate or adjust this product, please read
these instructions completely.
Multi-Function Controller
F1101W2052 @ Printed in Japan
VQT9557-2P 

2
FCC Note:
This device complies with Part 15 of the FCC Rules.
To assure continued compliance follow the attached
installation instructions and do not make any
unauthorized modifications.
This equipment has been tested and found to comply
with the limits for a class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and...

3
Contents
Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Parts and their functions  . . . . . . . . . . . . . . . . . . . . . . . . .4
Control panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Main unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Connections  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

4 1OPERATE lamp
This comes on when power is supplied to the main unit
and both the DC POWER switch on the main unit and the
OPERATE switch on the control panel are set to ON.
It goes off when either switch is set to OFF.
It flashes when a disconnection or some other problem
has occurred with the cable which is used to connect the
main unit and control panel.
2OPERATE switch
This is used to control the power supply of all the pan-tilt
head systems (each of which consists of a pan-tilt head
and convertible...

5 :GAIN [AUTO/MAN] button
This is used to select the camera’s gain control mode in
the pan-tilt head system currently selected.
Each time it is pressed, the AUTO mode or MANUAL
mode is selected in turn.
In the AUTO mode, the button’s lamp comes on; in the
MANUAL mode it goes off.
If, in the AUTO mode, the R/B GAIN/PED button is
pressed and the gain is adjusted, the maximum gain can
be set to one of two levels: AGC L or AGC H.
If, in the MANUAL mode, the R/B GAIN/PED button is
pressed and the gain is...

6 ?ABC button
This is used to automatically adjust camera’s black
balance in the pan-tilt head system currently selected.
Set the IRIS [AUTO/MANU/LOCK] button to AUTO (the
IRIS button is now lighted), and press the ABC button.
While the black balance is being adjusted, the ABC
button’s lamp flashes; when it has been adjusted
properly, it goes off. It comes on when it was not possible
to perform the adjustment.

If a pan-tilt head other than the AW-PH350 is being used,
the ABC button’s lamp also goes off...

7 ILAMP button
This controls the ON and OFF of the halogen lamp which
is connected to the pan-tilt head system currently
selected.  
Each time it is pressed, the lamp is turned ON or OFF in
turn.
When the halogen lamp is ON, the button’s lamp comes
on; when it is OFF, the lamp goes off.
It flashes when the halogen lamp has not been
connected or when the lamp has been disconnected or
some other problem has occurred.
JDEF button
This sets the defroster function ON or OFF when a pan-
tilt head (AW-PH600)...

8 PSTART POINT button
Press this to set the position at which the tracing memory
is to be started.
QSTART/STOP button
Press this to start or stop entry into the tracing memory.
RRESTORE button
Press this to correct or change what has been entered in
the tracing memory.
SRESET button
Press this to erase what has been entered in the tracing
memory.
TTR/PSET button
This is used to select the tracing memory mode or preset
memory mode.  
Each time it is pressed, the tracing memory mode or
preset memory mode...

9 XZOOM lever, FOCUS/IRIS dial
These are used to adjust the lens zoom in the pan-tilt
head system currently selected.
Depending on the direction in which the ZOOM lever is
tilted, TELE (telephoto) or WIDE (wide angle) is set, and
depending on the angle at which it is tilted, the zoom
speed is adjusted.
The lens focus or lens iris is adjusted using the dial at the
top of the lever.
Using the button on the top of the lever, the dial’s function
can be switched so that the dial will serve as a focus...

10
Parts and their functions
$Control panel
CONTROL/PREVIEW MONITOR OUT SEL
AUX 12345
TALLY TRACING MEMORY
LAMP
MENU
LIMIT
OFF LIMIT
ONFULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT R/B
GAIN/PED WHITE
BALAW C
GAIN
MODE
CLOSEWIDE NEAR
DATA SET
TR/PSET M.LOCK
MEMORY
IRIS IRIS
IRISOPENZOOMTELEFOCUS
FA R
CALL INCOM
LEVEL
FOCUS
OPEN
FA R TELE
OFFON OPERATE
WIDE
ZOOM/FOCUS/IRISABC
AT W
A
B
NG
OKSTART/STOP RESTORE RESET DEF WIP H/F EXT ND
OPTIONPA N / T ILT  SETCAMERA CONTROL
TRACING/PRESET MEMORY
IRIS...