Panasonic Multi Function Controller Aw Rp605 Operating Instructions

31
Operation
$Tracing memory settings
The multi-function controller is equipped with a tracing
memory function for entering the series of settings with
which pan-tilt head systems is operated.
The tracing memories are entered into TRACING/PRESET
MEMORY buttons 1 through 10.
1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2.Press the MENU button, and turn the menu setting
control (main), and set it so that the CONTROLLER
SETTING item appears at the top of the LCD...

328. The entry in the tracing memory commences as soon as
the pan, tilt, zoom, focus, iris or white balance mode
selection is initiated so proceed with the entry operation.
The START/STOP button stops flashing and comes on,
and the lamps of TRACING/PRESET MEMORY buttons
11 through 30 come on to provide a general guideline of
the time for which data can be entered.
Each of the No. 11 through No. 20 buttons indicates a
time of approximately 3 seconds; and each of the No. 21
through No. 30 buttons indicates...

33 1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Press the button in which the tracing memory data to be
recalled has been entered.
The pan-tilt head system is set to the start position
entered in the tracing memory.
3. After the pan-tilt head system has been set to the tracing
memory start position status and then stopped, press the
button in which the tracing memory data has been
entered again .
The pan-tilt head system now starts the operations
entered in the...

34 1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2.While holding down the RESET button, press the
buttons in which the tracing memory data to be deleted
has been entered.

The lamps of the buttons in which tracing memory data
has been entered (TRACING/PRESET MEMORY
buttons 1 through 10) come on when the RESET button
is pressed.
3. The buttons’ lamps go off, and the tracing memory data
is deleted.

Data cannot be deleted while the M.LOCK button’s lamp
is lighted....

35
Operation
$Preset memory settings
The multi-function controller is equipped with a preset
memory function for entering the positions and settings with
which the pan-tilt head system is to shoot.
Preset memory data is entered into TRACING/PRESET
MEMORY buttons 1 through 50.
1.Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Connect a color monitor to the VIDEO/Y OUT connector
on the main unit that corresponds to the pan-tilt head
system currently selected.
3. Use the...

G/L SETTING
CABLE LENGTH [SHORT]
H PHASE [± 0]
SC PHASE [COARSE: 1, FINE: ± 0]
CABLE COMP
CABLE COMP AUTO
CABLE COMP MANUAL (Y, C)
CABLE COMP MANUAL (Y Level)CABLE COMP MANUAL (f Response)
CONTROLLER SETTING
SIGNAL SELECT [C. VIDEO5C. VIDEO]
BUZZER SET [ON]
EXT CONTROL OUT [OFF]COMPONENT [Y/Pr/Pb] 4 [PAL OUTPUT SIGNAL]MEMORY LENGTH [30s]HEAD SW (R) FUNCTION [OFF]VIRTUAL STUDIO MODE [OFF]
P/T SETTING
PAN DIRECTION [NORMAL]
TILT DIRECTION [NORMAL]
ZOOM DIRECTION [NORMAL]
IRIS DIRECTION [NORMAL]FOCUS...

OThe factory settings are indicated in parentheses.
OThe setting values for items in parentheses with marked with an asterisk (§) are based on the AW-E800A being used as the camera.
When a camera other than the AW-E800A is to be used, change the setting to the initial setting of that camera.
OIt is possible to switch the speed at which the setting value of the items marked with Jchanges each time the jog dial is pressed.
Note that this function may not work with the AW-RP615 Control Panel (optional...

38
Setting menus
CABLE LENGTH (SHORT, LONG)
This item sets the compensation for the length of the BNC
cable used for the genlock signals.  “SHORT” is set when
the cable is less than 500 meters long; “LONG” is set when
it is 500 meters or longer.
H PHASE (–206 to +49)
This item is used to adjust the horizontal phase during
genlock.
SC PHASE (1, 2, 3, 4, –511 to +511)
This item is used to adjust the color phase during genlock.
CABLE COMP AUTO
When this item is selected and the OK button is pressed,
the...

39
Setting menus
PAN DIRECTION (NORMAL/REVERSE)
This item is used to select the operations in the horizontal
direction of the pan-tilt head system which are to be
performed by operating the PAN/TILT lever.
When NORMAL is selected as the setting, the pan-tilt head
system moves toward the left when the PAN/TILT lever is
tilted toward the L side, and it moves toward the right when
it is tilted toward the R side.
Conversely, when REVERSE is selected as the setting, the
pan-tilt head system moves in the...

40
Setting menus
SPEED WITH ZOOM POS. (OFF, 1, 2)
When 1 or 2 is selected as this item’s setting, the pan-tilt
operation of the pan-tilt head system is slowed down so that
the pan-tilt position will be more easily aligned when the
lens zoom is at the wide-angle position.
DIAGONAL MOTION (ON/OFF)
OFF : The pan-tilt head system moves to the position set in
the preset memory at maximum speed.
ON : The speed at which the pan-tilt head system moves
is adjusted so that it will move to the position set in
the...