Panasonic Multi Function Controller Aw Rp605 Operating Instructions

11 bDC 12V IN socket
The power from the main unit is supplied to this socket.
The socket is connected to the CONTROL PANEL
POWER OUT socket on the main unit using the
connecting cable (10 meters) supplied.

If the connection distance exceeds 10 meters, connect
the AW-PS505 AC adapter (optional accessory).
cCONTROL OUT connector
The control signals are output from this connector to the
main unit.  Use the connecting cable (10 meters) supplied
to connect the connector to the CONTROL IN TO
CONTROL PANEL [1]...

12 1POWER lamp
This lights up green when power is supplied to the main
unit and the DC POWER switch is set to ON.  It goes off
when the switch is set to OFF.
2DC POWER switch
This is the main unit’s power switch.
3DC 12V IN socket
The AW-PS505 AC adapter (optional accessory) is
connected to this socket.
When the AW-PS505 is used as the power source, 4
additional AW-PB605 boards can be installed in this unit,
making it possible to use up to 5 video boards in total.
Note that when any optional boards are...

8INCOM connector
This connector is used for connecting to the TALLY &
INCOM connector on the AW-SW300 live switcher, etc.
to enable inter-communication.
To perform inter-communication, use the inter-
communication system plug (Mini DIN 6-pin) supplied.
9
CONTROL OUT TO PAN/TILT HEAD connectors [1] to [5]
Connect these connectors to the IP/RP connector on the
AW-PH350 pan-tilt head using a straight cable equivalent
to 10BaseT (UTP category 5).  The connection distance
can be extended up to 1,000 meters....

14 @REMOTE connector
A personal computer or other external equipment is
connected here when a pan-tilt head system is to be
controlled by these equipments.
AVIDEO/Y IN connector
One end of a coaxial cable (equivalent to BELDEN 8281)
is connected here and the other end is connected to the
video output connector or Y/VIDEO output connector on
the pan-tilt head.
When the AW-PH350 is used as the pan-tilt head, a
connection distance of up to 1,000 meters is possible.
When any other pan-tilt head is used, a...

15 EVIDEO/Y OUT connector
The video signals adjusted by the cable compensation
circuit to match the length of the cable from the pan-tilt
head to the main unit are output from this connector.  
One end of a coaxial cable is connected here and the
other end is connected to the video input connector or the
Y signal input connector on a TV monitor, special effects
generator, VTR or other equipments.
FPr OUT connector
When component signals are supplied to the multi-
function controller, the Pr signals...

16
Connections
OUse the AW-PS505 (optional accessory) for the main
unit’s AC adapter and the AW-PS300 (optional
accessory) for the pan-tilt head’s AC adapter.
OConnect the DC 12V IN socket on the control panel with
the CONTROL PANEL POWER OUT connector on the
main unit, and the CONTROL OUT connector on the
control panel with the CONTROL IN TO CONTROL
PANEL connector 1 on the main unit using the cables (10
m) supplied.
To extend the connection distance between the control
panel and main unit beyond 10...

G/L I N Pb  OUT Pr / SDI
OUTY/VIDEO
OUT
1394CONTROL IN
IP/RPDC12V
IN
CAMERA I/F
LENSE I/F
ND/EXT SDI
IN
CSOP
O    I
FUSEFUSE
17
Connections
Pan-tilt head:
AW-PH350 Iris controlConvertible camera
Zoom lens
Zoom/focus control
AC adapter:
AW-PS300
Control panel
Connector cable
(accessory)
Main unitAC adapter:
AW-PS505 Y/VIDEO signal Pr signal Pb signal
Y/VIDEO signal
Pr signal
Pb signalG/L signal
G/L signal input
G/L through signal
output
AUX signal input
Video monitor outputPan-tilt head system control...

18
Connections
When using a pan-tilt head other than the
AW-PH350
When the AW-PH300, AW-PH300A, AW-PH500 or AW-
PH600 is to be used as a pan-tilt head, the level of the
control signals from the main unit must be converted from
RS-422 to RS-232C.
Consult with your dealer concerning the RS-232C/RS-422
converter and connecting cable.
Shown below is an example of the connections performed
by the RS-232C/RS-422 converter.
1 TXD+
RS-422 RS-232C
2 TXD–
3 RXD+
1 kΩ
390 Ω
1 kΩ VCCAD7306JR4 RXD–
5 GND
12345678GND...

O    I
FUSEFUSE
FUSEFUSE
FUSEFUSE
19
Connections
Example of system configuration
AC adapter:
AW-PS300
Main unit
Genlock signal generator
Switcher, special
effects generator,
etc.
Control panel
Remote control panel:
AW-RP615G/L signal VIDEO/Y
Pb
Pr
VIDEO/Y
Pb
Pr Video board:
AW-PB605
AUX
System
tally
Inter-communications
headsetHalogen lamp Pan-tilt head system
Preview color monitor
(75 Ωterminator)
Preview color monitor
(75 Ωterminator)Pan-tilt head system
control signal
AC adapter:
AW-PS505
AC adapter:...

20
Operation
$Turning on the power
1. Set all the power switches of the connected components
and the power switch of the AC adapter to ON.
2. Set the DC POWER switch on the main unit to ON.
3. Set the OPERATE switch of the control panel to ON.
Power is now supplied to the pan-tilt head systems
connected to the main unit, and the camera’s initial
settings are performed in sequence.
 
OAt the same time as the camera’s initial settings are
performed, the control panel’s PAN/TILT lever and
ZOOM lever...