Panasonic Mpeg2 Encoder Wj Gxe900 Operating Instructions
Here you can view all the pages of manual Panasonic Mpeg2 Encoder Wj Gxe900 Operating Instructions. The Panasonic manuals for TV Receiver are available online for free. You can easily download all the documents as PDF.
Page 31
31 Description Labels The description labels and the code labels are provided as standard accessories of the encoder and the decoder respectively. Attach each label on the top of the appliances as described below according to needs. Labels for Encoder Description label (1) There are descriptions about the "SW2" and the "STATUS" indicators (STATUS 1 - 8) on this label. Attach this label to the top front side of the encoder (shown in the illustration on the right), on the container box or...
Page 32
32 How to Display the Settings Menus The settings for the encoder and the decoder are required to operate for the first time respectively. (The settings will be required also when the settings are initialized.) The settings for the encoder and the decoder can be performed using a web browser installed on a PC. (Refer to the "System Requirements" of on page 8 about web browsers that can be used.) To perform the settings, connect the encoder or the decoder by one of the following. •Connect the...
Page 33
33 Setup with the Provided "Panasonic IP Setup"Software Set up the network of the encoder/decoder by using the "Panasonic IP Setup" software included on the provided CD- ROM. Note:If a firewall (including software) exists, allow access to all UDP ports. Otherwise, it is impossible to use the "Panasonic IP Setup" software. Items included in the software •IPSETUP (Panasonic IP Setup) •Operating Instructions (pdf file) 1. Double click the "IPSETUP" icon. The "Panasonic IP...
Page 34
![Page 34
34
The setup window appears.
SETUP
4. Set parameters for each item.
"IP Address"
"Subnet Mask"
"Default Gateway"
"DNS Server address"
5. Click the [SET] button after completing the
settings.
Important:It takes around 20 seconds to
complete the settings of the
encoder/decoder after the [SET] button is
pressed. If the power cord or the Ethernet
cable is detached before the settings are
completed, the settings may not be
performed correctly.
6. Turn off the power switch of...](http://img.usermanuals.tech/thumb/58/69443/w300_wj-gxe900_en_om_d-33.png "Page 34
34
The setup window appears.
SETUP
4. Set parameters for each item.
\"IP Address\"
\"Subnet Mask\"
\"Default Gateway\"
\"DNS Server address\"
5. Click the [SET] button after completing the
settings.
Important:It takes around 20 seconds to
complete the settings of the
encoder/decoder after the [SET] button is
pressed. If the power cord or the Ethernet
cable is detached before the settings are
completed, the settings may not be
performed correctly.
6. Turn off the power switch of...")
34 The setup window appears. SETUP 4. Set parameters for each item. "IP Address" "Subnet Mask" "Default Gateway" "DNS Server address" 5. Click the [SET] button after completing the settings. Important:It takes around 20 seconds to complete the settings of the encoder/decoder after the [SET] button is pressed. If the power cord or the Ethernet cable is detached before the settings are completed, the settings may not be performed correctly. 6. Turn off the power switch of...
Page 35
![Page 35
35
Begin the setup when the PC is in the same condition as it is just
after startup.
The "Control Panel" window appears.
1. Select "Control Panel" ([Start] - [Settings] -
[Control Panel]).
2. Click once to select the [Network] icon.
Network Setup of the PC
To set up the network of the PC, first change the TCP/IP settings of the PC to match the default settings of the
encoder/recoder. The following are the default network settings of the encoder/recoder.
•IP address of the encoder:...](http://img.usermanuals.tech/thumb/58/69443/w300_wj-gxe900_en_om_d-34.png "Page 35
35
Begin the setup when the PC is in the same condition as it is just
after startup.
The \"Control Panel\" window appears.
1. Select \"Control Panel\" ([Start] - [Settings] -
[Control Panel]).
2. Click once to select the [Network] icon.
Network Setup of the PC
To set up the network of the PC, first change the TCP/IP settings of the PC to match the default settings of the
encoder/recoder. The following are the default network settings of the encoder/recoder.
•IP address of the encoder:...")
35 Begin the setup when the PC is in the same condition as it is just after startup. The "Control Panel" window appears. 1. Select "Control Panel" ([Start] - [Settings] - [Control Panel]). 2. Click once to select the [Network] icon. Network Setup of the PC To set up the network of the PC, first change the TCP/IP settings of the PC to match the default settings of the encoder/recoder. The following are the default network settings of the encoder/recoder. •IP address of the encoder:...
Page 36
![Page 36
36
SETUP
The "Network" window appears.
Note:If the "TCP/IP" item is not displayed, refer to the operating
instructions of the OS and follow the procedures to install the
TCP/IP.
The "TCP/IP Properties" window appears.
3. Click the [Configuration] tab.
4. Click to select the TCP/IP protocol of the
currently used network card.
5. Click the [Properties] button.
6. Click the [IP Address] tab.
7. Click the "Specify an IP address" radio
button.
8. Enter the IP address and the...](http://img.usermanuals.tech/thumb/58/69443/w300_wj-gxe900_en_om_d-35.png "Page 36
36
SETUP
The \"Network\" window appears.
Note:If the \"TCP/IP\" item is not displayed, refer to the operating
instructions of the OS and follow the procedures to install the
TCP/IP.
The \"TCP/IP Properties\" window appears.
3. Click the [Configuration] tab.
4. Click to select the TCP/IP protocol of the
currently used network card.
5. Click the [Properties] button.
6. Click the [IP Address] tab.
7. Click the \"Specify an IP address\" radio
button.
8. Enter the IP address and the...")
36 SETUP The "Network" window appears. Note:If the "TCP/IP" item is not displayed, refer to the operating instructions of the OS and follow the procedures to install the TCP/IP. The "TCP/IP Properties" window appears. 3. Click the [Configuration] tab. 4. Click to select the TCP/IP protocol of the currently used network card. 5. Click the [Properties] button. 6. Click the [IP Address] tab. 7. Click the "Specify an IP address" radio button. 8. Enter the IP address and the...
Page 37
![Page 37
37
Using Windows 2000
The following procedures are examples when using Windows 2000. You can proceed in the same way when using
Windows NT.
Important:Log in as one of the administrators before beginning the setup.
Begin the setup when the PC is in the same condition as it is just
after the startup.
The "Network and Dial-up Connections" window appears.
1. Select "Network and Dial-up Connections"
([Start] - [Settings] - [Network and Dial-up
Connections]).
2. Click the right mouse button on...](http://img.usermanuals.tech/thumb/58/69443/w300_wj-gxe900_en_om_d-36.png "Page 37
37
Using Windows 2000
The following procedures are examples when using Windows 2000. You can proceed in the same way when using
Windows NT.
Important:Log in as one of the administrators before beginning the setup.
Begin the setup when the PC is in the same condition as it is just
after the startup.
The \"Network and Dial-up Connections\" window appears.
1. Select \"Network and Dial-up Connections\"
([Start] - [Settings] - [Network and Dial-up
Connections]).
2. Click the right mouse button on...")
37 Using Windows 2000 The following procedures are examples when using Windows 2000. You can proceed in the same way when using Windows NT. Important:Log in as one of the administrators before beginning the setup. Begin the setup when the PC is in the same condition as it is just after the startup. The "Network and Dial-up Connections" window appears. 1. Select "Network and Dial-up Connections" ([Start] - [Settings] - [Network and Dial-up Connections]). 2. Click the right mouse button on...
Page 38
![Page 38
38
SETUP
The "Local Area Connection Properties" window appears.
Note:If the "Internet Protocol (TCP/IP)" item is not displayed,
refer to the operating instructions of the OS and follow the
procedures to install the TCP/IP.
The "Internet Protocol (TCP/IP) Properties" window appears.
3. Click to select "Internet Protocol (TCP/IP)",
and then click the [Properties] button.
4. Click the "Use the following IP address"
radio button and enter the IP address and
the subnet...](http://img.usermanuals.tech/thumb/58/69443/w300_wj-gxe900_en_om_d-37.png "Page 38
38
SETUP
The \"Local Area Connection Properties\" window appears.
Note:If the \"Internet Protocol (TCP/IP)\" item is not displayed,
refer to the operating instructions of the OS and follow the
procedures to install the TCP/IP.
The \"Internet Protocol (TCP/IP) Properties\" window appears.
3. Click to select \"Internet Protocol (TCP/IP)\",
and then click the [Properties] button.
4. Click the \"Use the following IP address\"
radio button and enter the IP address and
the subnet...")
38 SETUP The "Local Area Connection Properties" window appears. Note:If the "Internet Protocol (TCP/IP)" item is not displayed, refer to the operating instructions of the OS and follow the procedures to install the TCP/IP. The "Internet Protocol (TCP/IP) Properties" window appears. 3. Click to select "Internet Protocol (TCP/IP)", and then click the [Properties] button. 4. Click the "Use the following IP address" radio button and enter the IP address and the subnet...
Page 39
![Page 39
39
Using Windows XP (Category View)
Begin the setup when the PC is in the same condition as it is just
after the startup.
The "Control Panel" window appears.
The "Network and Internet Connections" window appears.
1. Select "Control Panel" ([Start] - [Control
Panel]).
2. Double click the "Network and Internet
Connections" icon.
3. Double click the "Network Connections" icon.](http://img.usermanuals.tech/thumb/58/69443/w300_wj-gxe900_en_om_d-38.png "Page 39
39
Using Windows XP (Category View)
Begin the setup when the PC is in the same condition as it is just
after the startup.
The \"Control Panel\" window appears.
The \"Network and Internet Connections\" window appears.
1. Select \"Control Panel\" ([Start] - [Control
Panel]).
2. Double click the \"Network and Internet
Connections\" icon.
3. Double click the \"Network Connections\" icon.")
39 Using Windows XP (Category View) Begin the setup when the PC is in the same condition as it is just after the startup. The "Control Panel" window appears. The "Network and Internet Connections" window appears. 1. Select "Control Panel" ([Start] - [Control Panel]). 2. Double click the "Network and Internet Connections" icon. 3. Double click the "Network Connections" icon.
Page 40
![Page 40
40
SETUP
The "Network Connections" window appears.
The "Local Area Connection Properties" window appears.
The "Internet Protocol (TCP/IP) Properties" window appears.
4. Click to select "Local Area Connection", and
then click "Change settings of this
connection" in the "Network Tasks" menu.
5. Click to select "Internet Protocol (TCP/IP)",
and then click the [Properties] button.
Note: If the "Internet Protocol (TCP/IP)" item is
not displayed,...](http://img.usermanuals.tech/thumb/58/69443/w300_wj-gxe900_en_om_d-39.png "Page 40
40
SETUP
The \"Network Connections\" window appears.
The \"Local Area Connection Properties\" window appears.
The \"Internet Protocol (TCP/IP) Properties\" window appears.
4. Click to select \"Local Area Connection\", and
then click \"Change settings of this
connection\" in the \"Network Tasks\" menu.
5. Click to select \"Internet Protocol (TCP/IP)\",
and then click the [Properties] button.
Note: If the \"Internet Protocol (TCP/IP)\" item is
not displayed,...")
40 SETUP The "Network Connections" window appears. The "Local Area Connection Properties" window appears. The "Internet Protocol (TCP/IP) Properties" window appears. 4. Click to select "Local Area Connection", and then click "Change settings of this connection" in the "Network Tasks" menu. 5. Click to select "Internet Protocol (TCP/IP)", and then click the [Properties] button. Note: If the "Internet Protocol (TCP/IP)" item is not displayed,...