Panasonic Mobile Stand For Plasma Display TY-ST58PF20 Installation Instructions

							11
ÔŠ 

 

						

							12
ÔŠ 
Óå¶ÚßµÓè Š.w	“Ž`Th



 ˆµ»ïÅwŠ.	“
ÇZ;Úé	Íw
ØtK”
Š.
HZw­;va(g(ÈŠ›	“Ž`oXi^M{











Óå¶ÚßµÓè Š.w<
æ›Ëj	Í[sU’
	
²t¾V‡b{



<w
ˆµÖ”±”UŽ•h’fw‡‡	ÍtËj
	Í[o	“Ž`‡b{Š.
HZw­;va(g

ˆµÖ”±”

  
 

　
　映像・ディスプレイデバイス事業グループ

						

							13
English
WARNING
Installation and removal should only be carried out by a qualified technician.
• If the stand is not installed correctly, the Plasma display may fall over and become damaged, and 
personal injury may result.
Do not disassemble or modify the mobile stand.
•  Otherwise the unit may fall over and become damaged, and personal injury may result.
Set up in a location with little vibration that can support the weight of the unit.
•  Otherwise the unit may fall over or down, and personal injury may result.
Ensure that the installation location is strong enough to support long-term use.
• If its strength becomes insufficient over the course of long-term use, the display may topple over, 
possibly causing injury.
CAUTION
Do not use any plasma displays other than those given in the catalogue.
•  Otherwise the unit may fall over and become damaged, and personal injury may result.
Do not place weight of over 20 kg (44.09 lbs.) on the shelf plate.
•  Otherwise the unit may fall over or down, and personal injury may result.
Do not use the mobile stand if it becomes warped or physically damaged.
•  Otherwise the unit may fall over and become damaged, and personal injury may result.
Do not lubricate the casters.
• The casters may crack or became damaged, and the display may fall down and became damaged, and 
personal injury may result.
Do not climb on or hang from the plasma display or mobile stand.
• Be particularly careful that young children obey this caution. Otherwise the unit may fall over and 
become damaged, and personal injury may result.
Do not block the ventilation holes. Do not block the space between the bottom of plasma display and the 
floor when using the mobile stand. 
• Otherwise heat may build up inside and cause a fire.
Take steps to prevent toppling.
• Earthquakes or children climbing up or onto the display may cause the display to topple over, possibly 
resulting in injury.
Secure at least 10 cm (3.9 inches) of space at the top, bottom, left, and right of the plasma display. 
Also secure at least 7 cm (2.8 inches) of space at the back. 
• Failing to do so may result in a fire.
Keep the unit away from direct sunlight and heating equipment.
• Failure to do so may result in warping, deformation, or degradation of materials, and a loss of strength 
that may cause the equipment to fall over or break and cause injury.
The work of fitting or removing the plasma display must be performed by at least two people.
• The plasma display may fall and cause injury.
During assembly and setup work, make sure that all screws are securely tightened.
• If assembly is not performed correctly, the pedestal will not be able to support the weight of the display. 
This may result in the display falling over and becoming damaged, which may result in personal injury. 
Set up on a stable, level surface.
• Otherwise the unit may fall over and become damaged, and personal injury may result.
For installation, use the special-purpose constituent parts.
• Otherwise, the plasma display may fall off the mobile stand and be damaged, possibly causing injury.
Unlock the casters when moving the display.
• Otherwise the unit may fall over and become damaged, and personal injury may result.
Dispose of the product when it is no longer going to be used.
• Otherwise the unit may fall over and become damaged, and personal injury may result.
Safety precautions 
						

							14
Requests regarding handling
1)  Exercise care when selecting the location for the display because it may discolor or deform due to light 
or heat if it is placed where it is exposed to direct sunlight, or near a heater.
2)  For cleaning, wipe the display using a soft dry cloth (made of cotton or flannel). If the unit is extremely 
soiled, first wipe off soiling with a neutral detergent diluted in water, and then wipe with a dry cloth. Do 
not use cleaners such as benzene, thinner or furniture wax because they may cause paint peeling. 
(For information on cleaning the plasma display, see the plasma display’s instruction manual. If using a 
chemically-treated cloth, follow the instructions supplied with the cloth.)
3)  Do not affix adhesive tape or stickers to the product. Doing so may dirty the surface of the mobile 
stand. Do not allow long-term contact with rubber, vinyl products or the like. (Doing so will cause 
deterioration.)
4)  The panel of the plasma display is glass. Do not subject it to a strong force or impact.
Precautions for mobile stand assembly and setup work
● To ensure correct plasma display performance and prevent trouble, do not fit at any of the following 
locations.
    • Near sprinklers or fire/smoke detectors
    • Where there is a risk of exposure to vibration or impact
    • Near high-voltage wires or dynamic power supplies
    • Near sources of magnetism, heat, water vapor or soot
    • Locations exposed to air blown from heating equipment
    • Where droplets of condensation from an air conditioner or other unit may form
● For the plasma display power supply plug, use a power supply outlet that can be reached easily.
● Ensure good air flow so that the ambient temperature does not exceed 40 °C (104 °F). Failure to do this 
may cause heat to build up inside the plasma display, resulting in malfunction.
● Fit so there is no contact between the attachment bolts or power cord and any metal inside the wall.
● Spread a soft blanket or cloth over the floor so that the stand and floor will not be marked or scratched 
during the assembly and installation work.
● Perform the assembly and installation work on a flat and level surface, and follow the assembly and 
installation work instructions.
● When screwing down the parts, ensure that the screws are neither insufficiently tightened nor over 
tightened.
● Take sufficient care to ensure safety around you when performing the assembly and installation work or 
while moving about during the course of the work.
● Be sure to read and observe the “Safety precautions”.
PROFESSIONAL INSTALLATION IS REQUIRED.
PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING 
DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING.
English
This stand is intended for only Panasonic plasma display models (See page 121).
Use with other apparatus is capable of resulting in instability causing possible injury.
Safety precautions 
						

							15
Main parts
English
Components
Check that all the parts are accounted for and 
present in their designated quantities.
  Base unit with casters (2)
 Base joint (1)
 Support column (left/right)
  (One for each side)
 Shelf plate (1)
 Bracket for shelf plate (2)
 Top bracket for plasma display (1)
 Bottom bracket for plasma display (1)
Accessory parts
  Hexagon socket cap button bolt (M8 × 65) 
Spring washer/Flat washer 
Cap nut with flange (M8)
 (Four each)  
Hexagon socket cap button bolt (M8 × 70) 
Spring washer/Flat washer 
Cap nut with flange (M8)
 (Six each)  
Allen head 
countersunk screw 
Dished toothed washer 
Insulation spacer
 (Four each)
 
Screw for attaching bracket for shelf plate (M5 × 18) (4)
 
Screw for attaching bracket for plasma display (M5 × 18) (8)
 Screw for securing unit
  (M4 × 16) (2) Wood screw (4)

 Clamper (5)
 Cover stickers
  (48 (2 sheets)) Allen wrench (included tool) (1)
Left
Right
L
R
[The images shown in this manual are for illustrative purpose only.] 
						

							16
1.  Assembling of the stand
2.  Attaching the support columns 
Preparing hexagon socket cap button bolts 
3.  Perpendicular adjustment and fixing of 
the support columns
  Adjust the suppor t columns (left /right) 
 so that 
they are perpendicular to the stand base. Tightly 
fasten the four hexagon socket cap button bolts 
 
that temporarily fixed the support columns.
  (Tightening torque: 8 to 10 N•m)
1.  Assembling the stand base
Preparing hexagon socket cap button bolts 

Ready four sets by passing spring washers and flat washers over hexagon socket cap button 
bolts (M8 × 65).
When assembling, make so the caps nut of the hexagon socket cap button bolts are on the inside of the stand. Length 
of hexagon socket cap button bolts is 65 and 70 mm (2.6 and 2.8 inches). Be careful not to use the wrong bolts. 
  Face screw holes of base unit with casters 
 to 
the rear and align with base joint 
 as shown in 
the figure on the right, and fasten with the four 
readied hexagon socket cap button bolts 
 
(M8 × 65) and cap nuts with flanges 
.
  (Tightening torque: 8 to 10 N•m)
  Face the “L” and “R” marks of support columns  (left/
right) 
 to the inside, and insert the bottom plates 
into the back side of the stand base from above. 
Temporarily secure support columns (left/right) 
 
with the readied four hexagon socket cap button 
bolts 
 (M8 × 70) and cap nuts with flanges 
.
Ready six sets by passing spring washers and flat washers over hexagon socket cap button 
bolts (M8 × 70).
English
Assembly
Hexagon socket 
cap button bolt

(M8 × 65)
Screw holes
Front
Support column 
(left) 

Support column 
(right) 

Hexagon socket 
cap button bolt

(M8 × 70)
Stand 
baseCap nut with 
flange
 (M8)
Hexagon 
socket cap 
button bolt

(M8 × 70)
Framing squareTightly fasten
Base joint 

Hexagon socket 
cap button bolt 
 (M8 × 65)Base unit with 
casters 
Cap nut with flange
 (M8)
Face this 
side to the 
rear 
						

							17
5.  Preparation of the shelf plate
  
Face the unpainted side (back side) of the shelf 
plate 
 upward and place it on a soft cloth or the 
like. Align the positioning holes of the shelf plate 
with the bracket protrusions to position the two 
brackets for shelf plate 
, and attach them with 
four wood screws 
 through the outside holes.  
 (Tightening torque: 1 to 1.2 N•m)
 *  Do not excessively fasten the wood screws to 
prevent stripping screw holes. If a screw hole is 
stripped, use spare holes.
4.  Attachment of brackets for plasma 
display (top/bottom)
 ●  The attachment position differs according to the size 
of the plasma display to be set up.
(The figure on the right covers setting up a 50-inch 
TV.)
  Hang the tabs of the top bracket for plasma display 
 to the cutouts for temporarily holding the 
bracket for plasma display located on the front of 
the left and right support columns. Fasten with four 
screws for attaching bracket for plasma display 
 
from the side.
  (Tightening torque: 2 to 3 N•m)
  * See the figure on the right for attachment positions. 
  Hang the tabs of the bottom bracket for plasma 
display 
 to the cutouts for temporarily holding 
the bracket for plasma display located on the 
front of the left and right support columns. Fasten 
with four screws for attaching bracket for plasma 
display 
 from the side.
  (Tightening torque: 2 to 3 N•m)
  * See the figure on the right for attachment positions.English42
50
58
42
50
58
50
For 42-inch 
display
For 50-inch 
display
For bottom bracket
For top bracket
Wood screw

Spare 
holes 
(Inside)Bracket for 
shelf plate
Shelf 
plate
 Cutouts for temporarily 
holding the bracket for 
plasma display
Ta b
Support column 
(right)

Support column 
(left)

Top bracket for plasma display Cutouts for temporarily 
holding the bracket for 
plasma display
Bottom bracket for 
plasma display
For 42-inch 
display
For 50-inch 
display
For 58-inch 
display
For 58-inch 
display
Screw for attaching 
bracket for plasma 
display
 Screw for attaching 
bracket for plasma 
display
Bottom bracket for 
plasma display
 Top bracket for plasma display
 
						

							18
6.  Shelf plate fitting
 ●  Shelf plate fitting position can be adjusted for the top of 
the shelf plate to be either approx. 35 or 50 cm (13.8 or 
19.7 inches) from the floor.
  The figure shows an example of fitting to the upper level 
(50 cm [19.7 inches] from floor).
  Turn so the caution label of the readied shelf plate is 
on the back right, align the bracket for shelf plate 
 
screw holes and the support column 
 inside right 
and left screw holes, and fasten with four screws for 
fitting bracket for shelf plate 
.
 (Tightening torque: 2 to 3 N•m)
  Fasten from the left and right of the outside of the 
support column with the two readied hexagon socket 
cap button bolts 
 and cap nuts with flanges 
.
  (Tightening torque: 8 to 10 N•m)
If fitting at lower level (35 cm [13.8 inches] from 
floor)
  Fasten with two hexagon socket cap button bolts 
 
and cap nuts with flanges 
 through the bolt holes 
on the right and left sides of the upper level (50 cm 
[19.7 inches] from floor).
  Remove the two hexagon socket cap button bolts on 
the left and right sides at the lower level position. 
  Then fit the same way as in procedures 
 and 
 for 
fitting the upper level. 
2.  Preparing the plasma display
Attaching the insulation spacers
  
Place the front surface of the plasma display on a 
clean cloth that has no dirt or foreign objects on it, 
and follow the procedure below.
If the plasma display has any protruding parts, take 
care not to scratch or damage them.
  
Remove the four caps from the plasma display using 
a Phillips head screwdriver.
  Keep the caps that were removed in a safe place.
(They will be required if you use the pedestal.)
  
Using the supplied Allen wrench , attach accessory 
parts 
 (four Allen head countersunk screws, dished 
toothed washers, and insulation spacers) at the 
locations where the caps were removed as shown in 
the figure on the right.
(Tightening torque: 3 to 4 N•m)
Note
To change shelf plate height
 ●  Changing the shelf plate height after setting up the 
plasma display will make the stand unstable. Remove 
the plasma display from the mobile stand. 
Assembly
English
Phillips head screwdriver
Blanket
BlanketCap
Accessory parts 


  Screw for attaching 
bracket for shelf plate

  Screw for attaching 
bracket for shelf plate

  Hexagon socket cap button bolt

(M8 × 70)
  Hexagon socket cap button bolt

(M8 × 70)
Cap nut with flange
(M8)  Cap nut with flange
(M8)  
						

							19
3. Fitting to the stand
Note
Before fitting the plasma display, make sure to lock the 
casters.
1.  Fitting plasma display
  Engage the upper insulation spacers of the 
plasma display with the cutouts at the top of the 
mobile stand, and slowly lower the plasma display 
into place.
  While lifting the plasma display slightly, insert the 
bottom insulation spacers into the holes at the 
lower end of the mobile stand, and then lower the 
plasma display straight down into place.
Caster locked
Push the 
bottom of 
the leverPush the 
top of the 
lever Caster unlocked Locking and unlocking the casters
2.  Fixing of the plasma display
  Firmly tighten the two screws for securing unit 
 in 
the holes of the top bracket for plasma display 
.
  (Tightening torque: 1.5 to 2 N•m)
Note
Make sure to fit the screws for securing unit 
 on the left 
and right to prevent the plasma display from coming off.Mark A:  58-inch
Mark B: 42/50-inch
No mark: Spare
AB BA
AB B
A
CAUTION
If the plasma display is lifted too much, it will fall down 
and personal injury may result.
English
Cutout at top Upper insulation spacer
Hole at bottom Lower 
insulation 
spacer
  

Holes for screws for securing unit
(Use screw holes above cutouts 
with insulation spacers inserted)
Screw for securing unit
 
						

							20
4.  Setup and wiring of connected devices
  Insert the five clampers 
 in any of the six 
clamper attachment holes on the back side of  the 
left and right support columns at positions that 
make wiring easy. Wire as shown in the figure.
  Place cover stickers 
 in unused spare holes on 
the sides and back of the support columns and 
other locations. 
Note
Do not bundle the connection cables and main lead 
together.
5.  Preventing falling over
  In order to prevent the unit from falling over, fix 
the left and right support columns using strong 
cords or wires passed between the top and 
bottom brackets for plasma display, and connect 
them without slack to sturdy pillars or walls.
(Use commercially available cord or wire to 
prevent falling over.)
The distance between the pillar or wall and 
the rear of the plasma display must be 1 m 
(39.4 inches) or less.
Strong cords or wires 
available on the market
  [For safety reasons, always use the overturn/fall prevention accessories]
  The equipment may overturn in the event of an earthquake etc. Therefore, always use the overturn/fall 
prevention accessories. 
 *  The details in this section indicate how to reduce any damage or injury caused by this equipment overturning or 
falling due to an earthquake. However, there is no guarantee that the overturn/fall prevention accessories will 
be effective in all earthquake situations. 
Assembly
English
Clamper

Main lead and 
various cables
Cover stickers
Main lead 
and various 
cables