Panasonic Matrix Switcher Wj Sx650p Operating Instructions

21
Installing the Main Unit
Places to avoid
•Places exposed to direct sunlight or near a source of
heat such as a radiator
•Very dirty and dusty places
•Places subject to strong vibrations
•Near magnetic field sources such as a television or
speakers
•Near high-voltage cables such as a power cable
•Near noise sources such as fluorescent lamps
•Places where condensation forms easily
•Humid places
•Places where drastic temperature changes occur
•Places which are not level
•Steamy and oily places such as...

22
CONNECTIONS
Important:
Use only the recommended BNC connectors listed below.
Standards
Suffixes attached to the standards may be updated.
Other BNC connectors may cause video signal interruption, and damage the BNC receptacles on the rear panel of the unit.
fl 1.32 mm — fl 1.37 mm
fl 0.13 mm — fl 0.69 mm
RECOMMENDED
Tip dimensioins inside the BNC
 BNC
Tip 
(inside) Video (coaxial) Cable
For U.S.A.
For Europe
For JapanMIL-C39012C or MIL-C39012/16F
BS CECC 22120:1981
JIS C5412 

23
Basic System Connections
The following is a connection example to use one unit.
This unit x 1, camera x 30, monitor x 16, and recorder x 2
Video input board
Expansion slot
Video output board
AB1324657980
SYSTEM CONTROLLERAB1324657980
SYSTEM CONTROLLER
SERIAL
DATADATA CAMERA IN
CAMERA IN
CAMERA IN MONITOR OUT
MONITOR OUTMONITOR
OUT
Recorder
Recorder
~ ~
~
PC (WJ-SX650 Series 
Administrator Console)
78 ON6 12345
786 12345
786 12345
78 ON6 12345
Camera 1 to 30
Monitor 1 to 16
VIDEO OUT (Loop-thru...

24
Expanded System Connections
The following is a connection example to use two or more units.
This unit x 3, camera x 150, monitor x 32, and recorder x 10
~
~ ~
AB1324657980
SYSTEM CONTROLLERAB1324657980
SYSTEM CONTROLLER
Card cage connection
Card cage connectionCAMERA IN
CAMERA IN
CAMERA
INCAMERA
IN
VIDEO OUT
(Loop-thru output)
MONITOR OUT
MONITOR OUT
Recorder Recorder Recorder
Recorder Recorder
Recorder Recorder
Recorder RecorderRecorder
Camera 1 to 150
Monitor 1 to 32
System controller
DATA
DATA...

25
This unit x 4, camera x 240, monitor x 32, and recorder x 15
Recorder Recorder Recorder Recorder
Recorder Recorder Recorder Recorder
Recorder Recorder Recorder Recorder
Recorder Recorder Recorder
Card cage connection
Card cage connection
Card cage connection
Video input board
Video input board
Video input board
Video input board
Video input board
Video input board
Video input board
Video input board
Video output board
Video output board
AB1324657980
SYSTEM CONTROLLERAB1324657980
SYSTEM CONTROLLER
~
~...

26
Card Cage Connections
Card Cage WJ-SX650U is used for mounting additional Video Input Board WJ-PB65C32. Up to 3 video input boards can be
mounted into a card cage.
The following is a connection example to use additional card cages.
•Maximum unit connections: Matrix Switcher WJ-SX650 x 1, Card Cage WJ-SX650U x 3.
•Video Output Board 1 and 2 must be mounted into the same unit.
•Unit that has video output boards must be at the connection end.
•When connecting the EXTENSION 1 to 3 ports of each unit, use...

27
Camera Connections
The following is a connection example to use system cameras and combination cameras.
Notes:
•Make sure that the cable length is less than 900 m {3 000 ft} between the camera site and the unit when using RG-59/U,
BELDEN 9259 or equivalent cables. 
•To display recorded images on monitors connected to this unit, connect the MONITOR OUT connectors of recorders to the
CAMERA IN connectors of the unit.
•When connecting cameras to the unit, reserve more unused connectors than the recorder...

28
1:1 Connection
One camera is connected to one RS-485 (CAMERA) port.
Example: RS-485 cameras are connected to the CAMERA IN 9 and 12 connectors.
Note:Do not use unit numbers other than 1 to 8 for individual cameras. (Refer to the operating instructions of camera for set-
ting.)
Daisy Chain Connection
Two or more cameras can be connected to one RS-485 (CAMERA) port. Up to 8 cameras are available.
Example: RS-485 cameras are connected to the CAMERA IN 9 to 12 connectors 
VIDEO OUT 3
VIDEO OUT 4
VIDEO...

29
Monitor Connections
•The MONITOR OUT 1 to 16 connectors of Video Output Board 1 are assigned to Monitor 1 to 16.
•The MONITOR OUT 1 to 16 connectors of Video Output Board 2 are assigned to Monitor 17 to 32.
PC Connection
Refer to Serial (RS-232C) Connector Command Reference (PDF file on the supplied CD-ROM) for details on the connection
and communication settings.
OUT X-21 2 3 4 5 6 7 8MONITOR OUT9 10 11 12 13 14 1516
EXTENSION 1TERM.
OFF
ON
OUTIN
OUT X-3MODE MODEDATA
1 2
MODE MODEDATA
3 4TERM.OFF...

30
Recorder Connection
The following is a connection example to use recorders.
Note:Use recorders with the following versions.
•WJ-HD300 Series: Ver. 1.61 or later
•WJ-HD300A Series: Ver. 3.10 or later
Connection to Video Output Connectors of Recorders
To display recorder images on monitors connected to this unit
When the video output connectors of recorders are connected to CAMERA IN connectors of this unit, recorder images can be
displayed on Monitor 1 to 32.
The following is the connection...