Panasonic Matrix Switcher Wj Sx650p Operating Instructions

							21
Installing the Main Unit
Places to avoid
•Places exposed to direct sunlight or near a source of
heat such as a radiator
•Very dirty and dusty places
•Places subject to strong vibrations
•Near magnetic field sources such as a television or
speakers
•Near high-voltage cables such as a power cable
•Near noise sources such as fluorescent lamps
•Places where condensation forms easily
•Humid places
•Places where drastic temperature changes occur
•Places which are not level
•Steamy and oily places such as kitchens
Rack Mounting
When mounting this unit, use the following racks.
Standard Rack:WU-RS71 (29 units can be mounted.)
Long Rack:WU-RL76 (41 units can be mounted.)
EIA equivalents (Products of other manufacturers):EIA
19 inch rack, 450 mm {17-7/10} or more depth
Note:When mounting this unit into a rack of another manu-
facturer, Rack Mounting Screw (W2-MSS/5008) (Option)
or M5 x 12 screws (8 pcs.) are required.
1. Power off the unit.
2. Remove the rubber feet (4 psc.) on the bottom of the
unit by loosening the screws.3. Mount the unit into the rack by fixing the rack mounting
screws (locally procured: 8 pcs). (Refer to the following
illustration.)
Important:
•If the rack is subject to vibration, secure the rear of the
unit to the rack by using additional mounting brackets
(locally procured).
•To avoid loosening, secure the mounting screws surely.
•When operating the units, keep the temperature inside
the rack surely below 45 °C {113 °F}. 
•Mount the unit into the rack with a space equivalent to
approx. 1 unit (44 mm) or more to separate from other
devices.
•Mounting ventilation fan(s) in the rack is recommended
especially when the rack is covered with front lids.
•To prevent the unit from overheating, do not block the
ventilation openings or slots in the cover 
Remove the rubber feet.
Matrix Switcher WJ-SX650
Matrix Switcher WJ-SX650
Matrix Switcher WJ-SX650
Make a space equivalent to 
approx. 1 unit (44 mm) or more
EIA 19 inch rack 
						

							22
CONNECTIONS
Important:
Use only the recommended BNC connectors listed below.
Standards
Suffixes attached to the standards may be updated.
Other BNC connectors may cause video signal interruption, and damage the BNC receptacles on the rear panel of the unit.
fl 1.32 mm — fl 1.37 mm
fl 0.13 mm — fl 0.69 mm
RECOMMENDED
Tip dimensioins inside the BNC
 BNC
Tip 
(inside) Video (coaxial) Cable
For U.S.A.
For Europe
For JapanMIL-C39012C or MIL-C39012/16F
BS CECC 22120:1981
JIS C5412 
						

							23
Basic System Connections
The following is a connection example to use one unit.
This unit x 1, camera x 30, monitor x 16, and recorder x 2
Video input board
Expansion slot
Video output board
AB1324657980
SYSTEM CONTROLLERAB1324657980
SYSTEM CONTROLLER
SERIAL
DATADATA CAMERA IN
CAMERA IN
CAMERA IN MONITOR OUT
MONITOR OUTMONITOR
OUT
Recorder
Recorder
~ ~
~
PC (WJ-SX650 Series 
Administrator Console)
78 ON6 12345
786 12345
786 12345
78 ON6 12345
Camera 1 to 30
Monitor 1 to 16
VIDEO OUT (Loop-thru output)
(#7: ON)
(#8: OFF) (#7: OFF)
(#8: OFF)
MODE switchesMODE switches
MODE switchesWV-CU950/650
WV-CU360C/CJ
Terminal mode,
Line termination: ON 
						

							24
Expanded System Connections
The following is a connection example to use two or more units.
This unit x 3, camera x 150, monitor x 32, and recorder x 10
~
~ ~
AB1324657980
SYSTEM CONTROLLERAB1324657980
SYSTEM CONTROLLER
Card cage connection
Card cage connectionCAMERA IN
CAMERA IN
CAMERA
INCAMERA
IN
VIDEO OUT
(Loop-thru output)
MONITOR OUT
MONITOR OUT
Recorder Recorder Recorder
Recorder Recorder
Recorder Recorder
Recorder RecorderRecorder
Camera 1 to 150
Monitor 1 to 32
System controller
DATA
DATA DATA DATA
SERIAL
DATADATA
DATA
PC (WJ-SX650 Series 
Administrator Console)
Video input board
Video input board
Video input board
Video input board
Video input board
Video output board
Video output board 
						

							25
This unit x 4, camera x 240, monitor x 32, and recorder x 15
Recorder Recorder Recorder Recorder
Recorder Recorder Recorder Recorder
Recorder Recorder Recorder Recorder
Recorder Recorder Recorder
Card cage connection
Card cage connection
Card cage connection
Video input board
Video input board
Video input board
Video input board
Video input board
Video input board
Video input board
Video input board
Video output board
Video output board
AB1324657980
SYSTEM CONTROLLERAB1324657980
SYSTEM CONTROLLER
~
~ ~
DATA
DATA
DATA DATA
DATA
SERIAL
DATA
DATA DATA
DATADATA
DATA
DATADATA
Camera 1 to 240
Monitor 1 to 32
System controller
PC (WJ-SX650 Series 
Administrator Console)
VIDEO OUT
(Loop-thru output)
CAMERA IN
CAMERA IN
CAMERA IN
MONITOR OUT 
						

							26
Card Cage Connections
Card Cage WJ-SX650U is used for mounting additional Video Input Board WJ-PB65C32. Up to 3 video input boards can be
mounted into a card cage.
The following is a connection example to use additional card cages.
•Maximum unit connections: Matrix Switcher WJ-SX650 x 1, Card Cage WJ-SX650U x 3.
•Video Output Board 1 and 2 must be mounted into the same unit.
•Unit that has video output boards must be at the connection end.
•When connecting the EXTENSION 1 to 3 ports of each unit, use Expansion Cable Kit WJ-CA65L20K (Option) or WJ-
CA65L07K (Option).
•Connect nothing to the EXTENSION 1 port of the Video Output Board 2.
3C
1 2B
1 2 3AC IN3
2
1A
SIGNAL GND
SIGNAL GND
ON4-LineRS485(CAMERA) SET UPMODEON4-LineMODE
EXTENSION  3  INEXTENSION  2  IN4MODERS485 (CAMERA) RS485 (CAMERA)3MODE MODE MODE21IN C-3VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
4MODERS485 (CAMERA) RS485 (CAMERA)3MODE MODE MODE21IN B-3
TERM.OFF
ONEXTENSION 1OUTININ A-3EXTENSION 3 OUTEXTENSION 2 OUT
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
3C
1 2B
1 2 3AC IN3
2
1A
SIGNAL GND
SIGNAL GND
ON4-LineRS485(CAMERA) SET UPMODEON4-LineMODE
EXTENSION  3  INEXTENSION  2  IN4MODERS485 (CAMERA) RS485 (CAMERA)3MODE MODE MODE21IN C-3VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
4MODERS485 (CAMERA) RS485 (CAMERA)3MODE MODE MODE21IN B-3
EXTENSION 1TERM.OFF
ON
OUTININ A-3EXTENSION 3 OUTEXTENSION 2 OUT
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
3C
1 2B
1 2 3AC IN3
2
1A
SIGNAL GND
SIGNAL GND
ON4-LineRS485(CAMERA) SET UPMODEON4-LineMODE
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
EXTENSION  3  INEXTENSION  2  IN4MODERS485 (CAMERA) RS485 (CAMERA)3MODE MODE MODE21IN C-3
MODE MODE MODE MODEDATADATAEXTENSION 1TERM.OFF
ON
OUTINOUT X-31 2 3 4TERM.ON
ON
MODETERM.OFF
MODEDATA 4
HDR4/TMNL8
HDR2/TMNL4DATA 3
HDR3/TMNL7
HDR1/TMNL3DATA 2
TMNL6
TMNL2DATA 1
TMNL5TMNL1/PS DATAVideo Output Board 2
Video Output Board 1
OUT X-21 2 3 4 5 6 7 8MONITOR OUT9 10 11 12 13 14 1516
OUT X-1ALARM OUT 2ALARM OUT 1SERIALVS OUT
VS INVS OUT
(THRU)Video Output Board 1 Only
MODE MODE MODE MODEDATADATAEXTENSION 1TERM.OFF
ON
OUTINOUT X-31 2 3 4TERM.ON
ON
MODETERM.OFF
MODEDATA 4
HDR4/TMNL8
HDR2/TMNL4DATA 3
HDR3/TMNL7
HDR1/TMNL3DATA 2
TMNL6
TMNL2DATA 1
TMNL5TMNL1/PS DATAVideo Output Board 2
Video Output Board 1
OUT X-21 2 3 4 5 6 7 8MONITOR OUT9 10 11 12 13 14 1516
OUT X-1ALARM OUT 2ALARM OUT 1SERIALVS OUT
VS INVS OUT
(THRU)Video Output Board 1 Only
IN X-116 15 14 13 12 11 10 9CAMERA IN87654321
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
4MODERS485 (CAMERA) RS485 (CAMERA)3MODE MODE MODE21Line termination: ON at the connection end
Line termination: ON at the connection endLine termination: OFF Expansion Cable Kit 
WJ-CA65L20K or WJ-CA65L07K
4MODERS485 (CAMERA) RS485 (CAMERA)3MODE MODE MODE21 
						

							27
Camera Connections
The following is a connection example to use system cameras and combination cameras.
Notes:
•Make sure that the cable length is less than 900 m {3 000 ft} between the camera site and the unit when using RG-59/U,
BELDEN 9259 or equivalent cables. 
•To display recorded images on monitors connected to this unit, connect the MONITOR OUT connectors of recorders to the
CAMERA IN connectors of the unit.
•When connecting cameras to the unit, reserve more unused connectors than the recorder total number. (Refer to p. 30
Recorder Connections for details.)
RS-485 Camera Connections
There are two options to connect RS-485 cameras to this unit.
•1:1 connection: One camera is connected to one RS-485 (CAMERA) port. 
•Daisy chain connection: Up to 8 cameras can be connected to one RS-485 (CAMERA) port.
Notes: 
•Set the line termination to ON for cameras at the connection ends. Line termination setting is performed with the MODE 1 to
4 switches (refer to p. 28) at video input rear boards.
•Perform the RS-485 camera setting in RS485 CAMERA of SETUP MENU (refer to p. 53) or System – VD2/DATA/Cable
Comp. – RS485 Camera of WJ-SX650 Series Administrator Console.
•1 200 m {3 937 ft} is the total length limit of RS-485 cables.
•Recommended for RS-485 communication is AWG#22 or thicker one. The cable should be shielded, two-wire, twisted pair,
and with low impedance.
•Conform the 2-wire or 4-wire communication setting of this unit to that of RS-485 cameras.
The following is the details on MODE 1 to 4 switch settings.
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
EXTENSION    3  INEXTENSION   2  IN
4
MODERS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3
17
15 161 2 3 418 19 31 32
System cameraCombination 
camera
Video input rear board
ON
OFF2-wire communication Line termination: ON
4-wire communication Line termination: OFF 1234
ON
12
34 ON1234
4-wire 
communication2-wire 
communication 
						

							28
1:1 Connection
One camera is connected to one RS-485 (CAMERA) port.
Example: RS-485 cameras are connected to the CAMERA IN 9 and 12 connectors.
Note:Do not use unit numbers other than 1 to 8 for individual cameras. (Refer to the operating instructions of camera for set-
ting.)
Daisy Chain Connection
Two or more cameras can be connected to one RS-485 (CAMERA) port. Up to 8 cameras are available.
Example: RS-485 cameras are connected to the CAMERA IN 9 to 12 connectors 
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
EXTENSION   3  INEXTENSION   2  IN
4
MODERS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3
ON
1234
ON
1234
Connector
RS485
(CAMERA) 1
RS485
(CAMERA) 24-wire 
communication2-wire 
communication
(SW#4: ON) (SW#1 to 4: ON)
MODE switch settings
Video input rear boardsJunction Unit
WV-CA48/JN
RS-485 cableUnit number: 1
Line termination: ON Unit number: 1
Line termination: ON
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
EXTENSION   3  INEXTENSION   2  IN
4
MODERS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3
ON
1234
ON
1234
Connector
RS485
(CAMERA) 14-wire 
communication2-wire 
communication
(SW#4: ON) (SW#1 to 4: ON)
MODE switch settings
Video input rear boardsRS-485 cable Junction Unit
WV-CA48/JNDaisy Chain Connection Kit 
WV-CA48/10K
Unit number: 4
Line termination: ONUnit number: 3
Line termination: OFFUnit number: 2
Line termination: OFFUnit number: 1
Line termination: OFF
Notes:
•Among cameras connected to an RS485 (CAMERA) port in the daisy chain (4-wire communication), only one camera can
activate camera alarms.
•Do not use unit numbers other than 1 to 8 for individual cameras. (Refer to the operating instructions of camera for setting.)
•Do not set the same unit numbers for more than one camera in an RS-485 chain.  
						

							29
Monitor Connections
•The MONITOR OUT 1 to 16 connectors of Video Output Board 1 are assigned to Monitor 1 to 16.
•The MONITOR OUT 1 to 16 connectors of Video Output Board 2 are assigned to Monitor 17 to 32.
PC Connection
Refer to Serial (RS-232C) Connector Command Reference (PDF file on the supplied CD-ROM) for details on the connection
and communication settings.
OUT X-21 2 3 4 5 6 7 8MONITOR OUT9 10 11 12 13 14 1516
EXTENSION 1TERM.
OFF
ON
OUTIN
OUT X-3MODE MODEDATA
1 2
MODE MODEDATA
3 4TERM.OFF
ON
MODETERM.ON
MODEDATA 4
HDR4/TMNL8
HDR2/TMNL4DATA 3
HDR3/TMNL7
HDR1/TMNL3DATA 2
TMNL6
TMNL2DATA 1
TMNL5
TMNL1/PS DATAVideo Output Board 2
Video Output Board 1
OUT X-1
ALARM OUT 2ALARM OUT 1
SERIALVS OUT
VS IN
VS OUT
(THRU)Video Output Board 1 Only
1
2
3
4
15
16
Video output rear boards
OUT X-21 2 3 4 5 6 7 8MONITOR OUT9 10 11 12 13 14 1516
EXTENSION 1TERM.
OFF
ON
OUTIN
OUT X-3MODE MODEDATA
1 2
MODE MODEDATA
3 4TERM.OFF
ON
MODETERM.ON
MODEDATA 4
HDR4/TMNL8
HDR2/TMNL4DATA 3
HDR3/TMNL7
HDR1/TMNL3DATA 2
TMNL6
TMNL2DATA 1
TMNL5
TMNL1/PS DATAVideo Output Board 2
Video Output Board 1
OUT X-1
ALARM OUT 2ALARM OUT 1
SERIALVS OUT
VS IN
VS OUT
(THRU)Video Output Board 1 Only
Video output rear boardsPC (WJ-SX650 Series 
Administrator Console)
9-pin D-sub
(Female) 
						

							30
Recorder Connection
The following is a connection example to use recorders.
Note:Use recorders with the following versions.
•WJ-HD300 Series: Ver. 1.61 or later
•WJ-HD300A Series: Ver. 3.10 or later
Connection to Video Output Connectors of Recorders
To display recorder images on monitors connected to this unit
When the video output connectors of recorders are connected to CAMERA IN connectors of this unit, recorder images can be
displayed on Monitor 1 to 32.
The following is the connection procedure.
1. Assign Unit Address (System) to the recorders. (Refer to p. 34 q.)
Available unit addresses are 1 to 16. The unit address setting must be different from each other.
2. Decide the video input board to supply video input signals from recorder.
Choose a video input board that has more unused connectors (CAMERA IN 17 to 32) than the recorder total number.
Note:Only one video input board can be connected to the video output connector of recorders.
3. Connect the video output connectors (the monitor output 2 connector) of recorders and the CAMERA IN 17 to 32 connec-
tors of the unit.
Recorder number 
(Unit Address (System))
1
2
3
4
5
6
7
8 251617CAMERA IN connector of
video input board 
32 9 24
31 10 23
30 11 22
29 12 21
28 13 20
27 14 19
26 15 18Recorder number 
(Unit Address (System))CAMERA IN connector of
video input board 
Note:To supply video input signals from recorders to video input boards, perform the settings surely in RECORDER of SETUP
MENU (refer to p. 50) or System – Recorder of WJ-SX650 Series Administrator Console.