Panasonic Matrix Switcher Wj Sx650p Operating Instructions

							91
Check item and remedy ReferenceProblem
Cannot control a recorder.
RECORDER ERROR is dis-
played on the monitor, and
recorder control is unavail-
able.
During sequence, black
screen and NOT
ASSIGNED are displayed on
the monitor.
Auxiliary control does not
become OFF even after the
sequence, timer event, or
alarm event ends.
Timer event or camera event
is not activated.
• Check the LCD (or LED) display or indicators of system con-
troller. When Busy (or the BUSY indicator) is blinking (or
lighting), recorder control is not available.
14, 15
• Depending on the recorder status, response may be delayed.
Check the status and retry the control.–
• Did you edit the TEXT INFORMATION window using the but-
tons on the front panel of recorder? In this case, the selected
system controller becomes unavailable. Close the TEXT
INFORMATION window using the buttons on the front panel
of recorder.
–
• Check if Monitor 2 is selected with the MONITOR1/MONI-
TOR2 button of recorder. (Refer to the operating instructions
of recorder for details.) As the unit is connected to the MONI-
TOR OUT 2 connector of recorder, do not select Monitor 1
with the MONITOR1/MONITOR2 button of recorder. When
you have selected Monitor 1, perform an operation that is
available for Monitor 2 only (playback, etc.). Monitor 2 will be
selected automatically.
• Check the connection and settings between the recorder and
the unit.
• Check if the recorders version is correct.
WJ-HD300 Series: Ver. 1.61 or later
WJ-HD300A Series: Ver. 3.10 or later 
• Check if the sequence setting contains LCNs or camera
positions not registered. (When the setting contains camera
positions not registered, only black screen is displayed.)
• If the sequence, timer event, or alarm event has turned on
the auxiliary control, the auxiliary control does not become
OFF automatically. Turn off the auxiliary control manually, or
set an event that turns off the auxiliary control. 
• If the timer event or camera event is set to be activated at the
start time of the summer time (daylight saving time), the
event will not be activated.
• If the setting data is uploaded after the start time, the event
will not be activated.
• Timer event will not be activated when monitors are selected
by operators with higher priority than the timer event, display-
ing SETUP MENU, or being in the alarm mode.
–
30
30
62
59
71, 72
71, 72
71 
						

							92
Check item and remedy ReferenceProblem
Auto tracking ended before
the end time of camera event
setting.
Alarm event does not occur.
The image of camera associ-
ated with the alarm event was
not recorded.
The status before the alarm
occurrence is not recovered,
even though the alarm event
is reset.
Alarm modes of connected
devices are not reset even
after the unit is powered off.
Cannot open SETUP MENU
of the unit.
• Check if another camera event is not set for the camera.
• Check if the alarm input signal setting is ON in ALARM of
SETUP MENU.
• Check if the alarm event has been set.
• Check the active period setting of alarm schedule.
71
49
66
67
• Check if the alarm is not suspended and SETUP MENU is
not open on the associated monitor.
• Check the connection and settings between the recorder and
the unit.
48, 69
30
• Recording follows the recorder settings. Check the command
alarm setting and event recording setting of recorder.
• If an operator has activated a group sequence before the
alarm occurrence, and another operator reset the alarm or
performed operations on the monitor associated with the
group sequence, the status before the alarm occurrence is
not recovered.
• When you power off the unit, the alarm mode activated for
the unit is reset, but the alarm modes for the connected
devices are not reset. Power on the unit again, and perform
the Alarm All Reset operation.
• You cannot open SETUP MENU when another operator is
opening it.
• SETUP MENU cannot be displayed on a monitor associated
with an active alarm.
–
68
68
–
– 
						

							93
WJ-SX650 Series Administrator Console
Check item and remedy ReferenceProblem
! mark is displayed in the
LCN entry field.
• Check if the camera number not registered is set for the cam-
era position, tour sequence, group sequence, timer event,
alarm event, recorder, or camera input channel. Register the
camera number in System – Logical Camera Number.
–
! mark is displayed in the
CAM-P (camera position)
entry field.
Cannot set Control to ON in
System – Recorder.
Cannot set the RS-485 port
number of camera input chan-
nel.
An error message appears
when changing the monitor
setting in Sequence –
Group Sequence, and click-
ing Set.
! mark (in a circle) is dis-
played in the list of
Schedule – Timer Event.
! mark (in a triangle) is dis-
played in the list of
Schedule – Timer Event.
• Check if the camera position number not registered is set for
the tour sequence, group sequence, timer event, or alarm
event. Register the camera position number in Camera –
Camera Position.
• Check if the camera input channel connected to the recorder
is set RS485 in System – RS485 Camera. Set -- for the
channel.
• Check if Control is set to ON for the recorder connected to
the camera input channel in System – Recorder. Set OFF
for the recorder.
• Check if the group sequence is associated with an alarm
event. You cannot change the monitor settings of group
sequences associated with alarm events. Delete alarm event
settings with which the group sequence is associated.
Check if the camera number or camera position number not
registered is set for the event.
•Register the camera number in System – Logical Camera
Number.
•Register the camera position number in Camera –
Camera Position.
• Start time of event is set for the period during which an event
with higher priority has been set. Change the settings of start
time and priority of the event.
–
–
–
66
–
–
Monitor Display Mode parame-
ter in Monitor Display Mode of
Alarm – Alarm Event is dis-
played in gray, and you cannot
change the parameter.• Check if the monitor is associated with an alarm event. You
cannot change the monitor display modes of monitors associ-
ated with alarm events. Delete alarm event settings for which
the monitor is assigned.
66
Cannot click a checkbox to
activate Auto Login 
and Auto
Logout 
in Controller – Auto
Login/Auto Logout.
• Check if the DATA port is set to PSD or HDR in System –
DATA Port. 
You cannot set auto login and auto logout for DATA ports set
to PSD or HDR. Set the DATA port to TMNL.
– 
						

							94
The power cord insulation is
damaged.
The power cord, plug and
connectors get hot during use.
The power cord gets hot when
bent or stretched.
The power cord, plug and connectors are worn out. This may
result in electric shock or a fire. Unplug the power plug from
the AC outlet immediately, and refer to qualified service per-
sonnel.
–
Check item and remedy ReferenceProblem
Power Cord, Connectors, and Power Plug
Check the power cord, connectors, and power plug regularly. 
						

							95
SPECIFICATIONS
Matrix Switcher WJ-SX650 Series
Power Source: 120 V AC, 60 Hz
Power Consumption: 60 W
Ambient Operating Temperature:–10 °C to +50 °C {14 °F to 122 °F}*
1
Ambient Operating Humidity: Less than 90 %
Video Input Board: x 1
Camera Input (CAMERA IN 1 to 32): 1 V [P-P]/75 Ω(BNC x 32), composite video signal 
0.5 V [P-P]/75 Ωdata signal and 2.5 V [P-P]/75 Ωvertical timing pulse multi-
plexed
Video Output (VIDEO OUT 1 to 4): 1 V [P-P]/75 Ω(25-pin D-sub connector x 4)*
2, active loop-thru output
Alarm Input (ALARM IN): N.O. (Normally Open contact) or N.C. (Normally Close contact) selectable x 32
(37-pin D-sub connector)
RS-485 (Camera) Port: 6-conductor modular jack x 4 (2-wire or 4-wire communication, with termination
switches (MODE 1 to 4))
Extension Port (EXTENSION IN 2, 3): 37-pin D-sub connector x 2
Video Output Board: x 1
Monitor Output (MONITOR OUT 1 to 16): 1 V [P-P]/75 Ω(BNC x 16)
Data Port (DATA 1 to 4)
DATA 1: Terminal Mode (TMNL) (PS·Data Mode (PS·DATA) selectable*
3)
DATA 2: Terminal Mode (TMNL)
DATA 3, 4: Terminal Mode (TMNL)/Digital disk recorder (HDR) selectable
6-conductor modular jack x 4 (With termination switches (MODE 1 to 4))
Alarm Output (ALARM OUT 1, 2)
Alarm Output:  Open collector output x 32, Max. 24 V DC, 100 mA
Alarm Recover Output:  Non-voltage make contact input x 16
Time Adjust Input*
3:  Non-voltage make contact input x 1
Time Adjust Output*3:  Open collector output x 1, Max. 24 V DC, 100 mA
Extension Port (EXTENSION 1 IN, OUT)*3: 6-conductor modular jack x 2 (With a termination switch (TERM: ON, OFF))
VS Input*3: 1 V [P-P]/75 Ω(VS IN)
VS Output*3: (VS OUT (THRU)): VS loop-thru output
(VS OUT): 1 V [P-P]/75 Ω(VS)
Serial Port*
3: 9-pin D-sub connector x 2
Expansion slot: x 1
RS-485 (Camera) Port*
4: 6-conductor modular jack x 4 (2-wire or 4-wire communication, with termination
switches (MODE 1 to 4))
Functions: Monitor control (Camera selection, tour sequence, group sequence, group pre-
set, OSD display)
Camera/Receiver control (Coaxial/RS-485 communication)
Recorder control
Alarm control (Alarm event, Alarm ACK, Alarm reset, Alarm suspension, Alarm
History Display)
Timer event, Camera event
Dimensions: 420 mm (W) X 265 mm (H) X 372 mm (D)
{16-9/16 (W) X 10-2/5 (H) X 14-3/5 (D)} (excluding rubber feet and projections)
Weight: 19.0 kg{42 lbs.}
*
1In the constant operation
*2When this unit is powered off, this signal will not be output even with the acceptation of video input signal.
*3Not available when the MODE switches are set as Video Output Board 2
*4Available only when Video Input Board WJ-PB65C32 is mounted 
						

							96
Card Cage WJ-SX650U
Power Source: 120 V AC, 60 Hz
Power Consumption: 60 W
Ambient Operating Temperature:–10 °C to +50 °C {14 °F to 122 °F}*
5
Ambient Operating Humidity: Less than 90 %
Expansion slot: x 3
RS-485 (Camera) Port
*6: 6-conductor modular jack x 12 (2-wire or 4-wire communication, with termination
switches (MODE 1 to 4))
Extension Port (EXTENSION 1 IN, OUT): 6-conductor modular jack x 2 (With a termination switch (TERM: ON, OFF))
Extension Port (EXTENSION IN 2, 3): 37-pin D-sub connector x 2
Extension Port (EXTENSION OUT 2, 3): 37-pin D-sub connector x 2
Dimensions: 420 mm (W) X 265 mm (H) X 372 mm (D)
{16-9/16 (W) X 10-2/5 (H) X 14-3/5 (D)} (excluding rubber feet and projections)
Weight: 18.0 kg{40 lbs.}
Video Input Board WJ-PB65C32
Camera Input (CAMERA IN 1 to 32): 1 V [P-P]/75 Ω(BNC x 32), composite video signal
0.5 V [P-P]/75 Ωdata signal and 2.5 V [P-P]/75 Ωvertical timing pulse multi-
plexed
Video Output (VIDEO OUT 1 to 4): 1 V [P-P]/75 Ω(25-pin D-sub connector x 4)
*7, active loop-thru output
Alarm Input (ALARM IN): N.O. (Normally Open contact) or N.C. (Normally Close contact) selectable x 32
(37-pin D-sub connector)
Dimensions
Main Board: 340 mm (W) X 48 mm (H) X 225 mm (D)
{13-2/5 (W) X 1-9/10 (H) X 8-4/5 (D)}
IN X-2 Board: 355 mm (W) X 21 mm (H) X 115 mm (D)
{14 (W) X 4/5 (H) X 4-1/2 (D)} 
IN X-1 Board: 355 mm (W) X 38 mm (H) X 115 mm (D)
{14 (W) X 1-1/2 (H) X 4-1/2 (D)}
Video Output Board WJ-PB65M16
Monitor Output (MONITOR OUT 1 to 16): 1 V [P-P]/75 Ω(BNC x 16)
Data Port (DATA 1 to 4)
DATA 1: Terminal Mode (TMNL) (PS·Data Mode (PS·DATA) selectable
*8)
DATA 2: Terminal Mode (TMNL)
DATA 3, 4: Terminal Mode (TMNL)/Digital disk recorder (HDR) selectable
6-conductor modular jack x 4 (With termination switches (MODE 1 to 4))
Alarm Output (ALARM OUT 1, 2)
Alarm Output: Open collector output x 32, Max. 24 V DC, 100 mA
Alarm Recover Output: Non-voltage make contact input x 16
Time Adjust Input
*8: Non-voltage make contact input x 1
Time Adjust Output*8: Open collector output x 1, Max. 24 V DC, 100 mA
Extension Port (EXTENSION 1 IN, OUT)*8: 6-conductor modular jack x 2 (With a termination switch (TERM: ON, OFF))
VS Input*8: 1 V [P-P]/75 Ω(VS IN)
VS Output*8(VS OUT (THRU)): VS loop-thru output
(VS OUT): 1 V [P-P]/75 Ω(VS)
Serial Port
*8: 9-pin D-sub connector x 2
Dimensions
Main Board: 340 mm (W) x 48 mm (H) x 225 mm (D)
{13-2/5 (W) X 1-9/10 (H) X 8-4/5 (D)} 
OUT X-1 Board: 355 mm (W) X 38 mm (H) X 120 mm (D)
{14 (W) X 1-1/2 (H) X 4-7/10 (D)} 
OUT X-2 Board, OUT X-3 Board: 355 mm (W) X 21 mm (H) X 115 mm (D)
{14 (W) X 4/5 (H) X 4-1/2 (D)}  
						

							97
*5In the constant operation*64 ports available with each Video Input Board WJ-PB65C32*7When this unit is powered off, this signal will not be output even with the acceptation of video input signal.*8Not available when the MODE switches are set as Video Output Board 2
Expansion Cable Kit WJ-CA65L20K/WJ-CA65L07K
Video cable: 37-pin D-sub x 2 (WJ-CA65L20K: 2 m {6-3/5}, WJ-CA65L07K: 0.7 m {2-3/10}) 
Communication cable: 6-conductor modular x 1
2 m {6-3/5}
D-sub/BNC Video Cable WJ-CA68
25-pin D-sub – BNC x 8 conversion
50 cm {19-7/10}
STANDARD ACCESSORIES
Operating Instructions (This Document)  ................................................ 1 pc.
CD-ROM* ................................................................................................ 1 pc.
* The following files are included on the CD-ROM.
•WJ-SX650 Series Administrator Console (Application)
•Serial (RS-232C) Connector Command Reference (PDF file)
Warranty Card ......................................................................................... 1 pc.
The following part is used during installation procedures.
Power Cord .............................................................................................. 1 pc. 
						

							Panasonic Canada Inc.5770 Ambler Drive,Mississauga, 
Ontario, L4W 2T3 Canada (905)624-5010
http://www.panasonic.ca
Panasonic Sales Company
Division of Panasonic Puerto Rico Inc.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina
P.R. 00985(809)750-4300
Panasonic System Solutions Company, 
Unit Company of Panasonic Corporation of North America
Security Systems 
www.panasonic.com/security
For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094
Zone Office
Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 
Central: 1707 N. Randal Road, Elgin, IL 60123 
Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 
Western: 6550 Katella Ave., Cypress, CA 90630 
© 2005 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. NM0805-1095       V8QA6317BN       Printed in Japan