Panasonic Matrix Switcher Wj Sx650p Operating Instructions

							61
Note:When you use WJ-HD300 Series, start playback
before pressing the GO TO LAST button.
 WV-CU360C/CJ
This operation is not available.
 Recorder Control End
Note:Before this operation, stop playback or search play-
back surely.
To finish recorder control, select a camera.
The monitor display will become the status before recorder
control.
 Recorder Selection
Before recorder control procedures not described in this
chapter, you need to select a recorder in advance. In the
following example, you will open SETUP MENU of Recorder
16.
 WV-CU950/650
1. Enter the desired recorder number by pressing the
numeric buttons. The entered number will appear on
the LCD.
2. Press the RECORDER button. The recorder will be
selected.
3. Press the MENU button repeatedly until System Setup
appears on the LCD.
4. Press the F1 button. SETUP MENU of recorder will be
displayed on the selected monitor.
Note:To close the SETUP MENU, press the F2 button.
 WV-CU360C/CJ
1. Enter the desired recorder number by pressing the
numeric buttons. The entered number will appear on
the LED display.
2. Press the RECORDER button. The recorder will be
selected.
3. Press the SETUP button while holding down the SHIFT
button. SETUP MENU of recorder will be displayed on
the selected monitor.
Note:To close the SETUP MENU, press the SETUP button
while holding down the SHIFT button.
 Note
If a selected recorder directly connects an external monitor,
black screen will be displayed on the monitor with the mes-
sage RECORDER CONTROL. Refer to p. 30 for connec-
tion.  
						

							62
 Descriptions of Sequence
Sequence is the function to switch camera images automatically.
There are two sequences:
•Tour sequence
•Group sequence
 Tour Sequence
Camera images are displayed on a selected monitor, and they are sequentially switched according to the setting. 
•Up to 32 tour sequences can be registered.
•Up to 64 steps can be set for a tour sequence.
 Group Sequence
Camera images are displayed on two or more monitors, and they are sequentially switched according to the setting. 
•Up to 8 group sequences can be registered.
•Up to 32 steps can be set for a group sequence.
 Group Preset
Spot camera images are simultaneously displayed on two or more assigned monitors. Up to 24 (Group Sequence 9 to 32)
group presets can be registered.
RUNNING SEQUENCE
Monitor 1
Monitor 2
Monitor 3Step 1 Step 2 Step 3Camera 1
Preset 1
Camera 10
Preset 2
Camera 100
Preset 3Camera 5
Camera 20
Preset 10
Camera 300Camera 7
Camera 50
Camera 900
Preset 200
Displayed for 2 seconds Displayed for 10 seconds Displayed for 30 seconds
......
......
...... 
						

							63
Setting item
LCN (Logical Camera Number) 
Preset
AUX1/2
DwellParameter Remarks
1 to 999
1 to 256
ON, OFF, - -
1 to 30 secCamera position numbers are also avail-
able for parameters. (CAM-P)
–
Dwell time to display each camera
image
(Group preset has no sequence steps,
and Dwell setting is not available.)
 Sequence Setting
Sequence setting is performed in Sequence of WJ-SX650 Series  Administrator Console. The following settings are available
for each sequence step.
Note:Preset and AUX1/2 will not be activated for cameras selected by operators with higher priority or restricted by the cam-
era access setting  
						

							64
 Tour Sequence
WV-CU950/650
1. Enter the desired sequence number by pressing the
numeric buttons. The entered number will appear on
the LCD.
2. Press the TOUR SEQ button. The tour sequence will be
activated.
 WV-CU360C/CJ
1. Enter the desired sequence number by pressing the
numeric buttons. The entered number will appear on
the LED display.
2. Press the TOUR SEQ button. The tour sequence will be
activated.
 Group Sequence/Preset
WV-CU950/650
1. Select a monitor assigned for desired group
sequence/preset. (Refer to p. 57 Monitor Selection.)
2. Enter the desired sequence number by pressing the
numeric buttons. The entered number will appear on
the LCD.
3. Press the GROUP SEQ button while holding down the
SHIFT button. The group sequence will be activated.
 WV-CU360C/CJ
1. Select a monitor assigned for desired group
sequence/preset. (Refer to p. 57 Monitor Selection.)
2. Enter the desired sequence number by pressing the
numeric buttons. The entered number will appear on
the LED display.
3. Press the GROUP SEQ button. The group sequence will
be activated.
Notes:
•If you have specified Group Sequence 9 to 32 in Step
2, group preset will be activated. The system status will
be the same as that after camera selection.
•Group sequence/preset will not be activated for moni-
tors selected by operators with higher priority or
restricted by the monitor access setting 
•When one of the monitors assigned for the active group
sequence is controlled by a higher-priority operator,
you cannot control the monitors. (Monitor busy) 
						

							65
 Sequence Pause
You can pause an active tour or group sequence. When a
group sequence is paused on a monitor, all sequences will
be simultaneously paused on other monitors.
1. Press the SEQ PAUSE*
1(or PAUSE*2) button.
Sequence will be paused.
2. Press the SEQ PAUSE*
1(or PAUSE*2) button again to
restart the sequence.
*
1WV-CU950/650
*2WV-CU360C/CJ
Available operations during sequence pause
•Sequence step forward/backward
You can move the sequence one frame to the next or
previous step by pressing the + or – button.
•Camera control
You can control the camera whose image is being dis-
played on the monitor.
 Sequence Stop
When a tour or group sequence is stopped, the camera at
the stopped step will be selected. When a group sequence
is stopped on a monitor, all sequences will be simultane-
ously stopped on other monitors.
 WV-CU950/650
Press the SEQ STOP button while holding down the SHIFT
button.
Sequence will be stopped.
 WV-CU360C/CJ
Press the STOP button.
Sequence will be stopped.
Note
Sequence will also be stopped when you select a camera
during the sequence is activated. Then, the image of
selected camera will be displayed on the monitor. 
						

							66
ALARM DESCRIPTIONS
Alarm Occurrence
When this unit accept an alarm input signal (terminal alarm, camera alarm, recorder alarm, serial alarm, or video loss), an
alarm event (tour sequence, etc.) is activated automatically. Each alarm input signal is associated with an alarm event setting.
(The setting activates the alarm input signal and alarm event.) Up to 1 024 alarm event settings are available. The alarm event
setting is performed in Alarm – Alarm Event of WJ-SX650 Series  Administrator Console.
By performing the settings of Alarm Event, the following events will be activated when this unit accepts an alarm input signal.
•Alarm event information will be displayed on the associated monitors (Refer to p. 13 Monitor Display Information.)
•Depending on the setting of Display Mode, camera images will be displayed, or sequences will be activated on the asso-
ciated monitors. In this document, these actions are mentioned as the alarm mode, and pictures displayed during the
alarm mode is mentioned as alarm pictures.
•Depending on the setting of Recording Source LCN, event recording will be activated. (Recording will follow the com-
mand alarm setting and event recording setting of recorder. Refer to the operating instructions of recorder for details.)
•Depending on the setting of Alarm Output, alarm output signal will be supplied from the video output board, and external
alarm devices (buzzer, etc.) can be activated.
Notes: 
•To activate terminal alarm output signals, perform settings of No.1 to 64. No.65 and greater are assigned for serial
commands. 
•To activate serial alarm output signals, serial command settings are required. The settings are performed in
Communication – Serial Command of WJ-SX650 Series Administrator Console. 
•ALARM indicators of all system controllers blink.
•Up to 10 000 alarm records are saved chronologically.  The latest 1 000 alarm records can be displayed as the alarm his-
tory on the monitor. (Refer to p. 69 Alarm History Display.) The Alarm History can be downloaded from the PC to the unit.
•Alarm information is notified to the PC in serial commands. The serial command setting is performed in Communication –
Serial Command of WJ-SX650 Series Administrator Console. 
Terminal alarm setting
No.11(Dish)No.10 (Pot)
No.1 (Entrance)
Sensor 
system
Alarm Input 256
Matrix Switcher WJ-SX 650650
Alarm input signal 
from a sensor
ALARMTIMERHDD 2ERRORHDD 1 ALARM
SUSPEND
ALARM
RESETOPERATEMONITOR1
MONITOR2159132610/014371115481216SEQ SHIFT OSDPA N /
TILTSTOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUSTEXTCOPYDISK SELECTEL-ZOOMMARKLOGOUTIRIS
PRESET
/AUTOA-B
REPEATGOTO
LASTLISTEDSEARCH
BUSYSETUP
/ESCSETREV–+FWDPULLDigital Disk Recorder
WJ-HDPA N / T I LTSLOW
Infrared sensor Preset Position 1
(Zooming in No.1 (Entrance))
Monitor 5 Terminal Alarm 
256This unit Camera 100
PC Alarm Output 50
Recorder 1Records the image 
of Camera 100.
(Recording follows  
the command alarm 
setting and event 
recording setting of 
recorder.)
Notifies the 
alarm event 
occurrence.
No. Display ModeSpot
MonitorRecording
Source (LCN)Alarm Output
LCN Preset
256 SPOT 100 1 5 100 50 
						

							67
Alarm Modes
The following alarm modes (Display Mode settings) are
available. (Alarm mode follows the setting of Display
Mode.)
Spot
The image of associated camera will be displayed on the
monitor. Preset position or auxiliary control will be activated.
The following alarm modes (=patterns to display alarm pic-
tures on a monitor) are available. (Regardless of alarm
modes, alarms occur to all the associated cameras.) The
alarm mode setting is performed in Alarm – Alarm Mode
of WJ-SX650 Series Administrator Console or the ALARM
menu of SETUP MENU.
• Sequence mode
Alarm pictures are sequentially displayed on the associated
monitor.
• Earliest mode
The earliest alarm picture is displayed on the associated
monitor.
• Latest mode
The latest alarm picture is displayed on the associated
monitor.
Tour Sequence
Tour sequence is activated on the associated monitor. 
Group Sequence/Preset
Group sequence is activated on the associated monitors. 
OFF
Only the alarm information is displayed on the associated
monitor. Alarm does not occur to monitors and cameras.
Notes:
•When a tour sequence, group sequence, or group pre-
set is activated as an alarm event, the earlier alarm
event on the monitor will be reset. 
•When 33 or more alarms (spot mode) occur to a moni-
tor, older alarms will be reset chronologically. 
•After occurrence, the same alarm will be suspended for
5 seconds.
•By the alarm schedule setting, alarm events can be
deactivated in the specified periods. The alarm sched-
ule setting is performed in Alarm – Alarm Event of
WJ-SX650 Series Administrator Console.
Video Loss
To display the video loss information on associated moni-
tors and save the video loss history without making alarms
occur to monitors and cameras, set Display Mode to OFF. 
Note:If Alarm A (Display Mode is OFF) occurs while
Alarm Bs (Display Mode is Spot, Tour Sequence or
Group Sequence) are being activated, the Alarm A
information will be displayed on the monitor after all
Alarm Bs have been reset.
Alarm 1Alarm 2
Alarm 3Alarm 4
Alarm 4
Alarm 1 
						

							68
ALARM CONTROL
Alarm Acknowledgement (ACK)
By acknowledging an alarm occurrence on an associated
monitor, you can control alarm pictures.
WV-CU950/650
While a monitor in the alarm mode status is selected, press
the ACK button. (During the alarm mode status, Alarm
sign is blinking on the LCD.)
The alarm event will be acknowledged. (Alarm sign will
change to steady light.)
WV-CU360C/CJ
While a monitor in the alarm mode status is selected, press
the ACK button. (During the alarm mode status, the alarm
number is blinking on the LED display.
The alarm will be acknowledged. (The alarm number will
change to steady light.)
In the ACK status, the following operations are available.
Camera Control
You can control panning/tilting of cameras, or move cam-
eras to preset positions, etc.
Alarm Picture Change
When two or more alarms are occurring, you can change
alarm pictures displayed on the monitor in order or reverse
order.
WV-CU950/650
To change alarm pictures on the monitor, press the + or –
button. The alarm pictures will be displayed in order or
reverse order.
WV-CU360C/CJ
To change alarm pictures on the monitor, press the NEXT
or PREV button. The alarm pictures will be displayed in
order or reverse order.
Alarm Individual Reset
You can reset each acknowledged alarm separately, and
return to the status before alarm occurrence. While two or
more alarms are occurring, the system will remain in the
alarm mode even after an alarm reset.
To reset an acknowledged alarm, press the ACK button.
The alarm will be reset.
Notes: 
•An alarm whose display mode setting is OFF will not be
the ACK status. The alarm will be reset by every press-
ing the ACK button.
•If AUTO RESET has been set to ON, alarms will be reset
automatically after the specified time. AUTO RESET set-
ting is performed in Alarm – Alarm Mode of WJ-
SX650 Series Administrator Console or the ALARM
menu of SETUP MENU. Refer to p. 49 ALARM of SETUP
MENU.
Alarm Monitor Reset
You can reset all the alarms occurred to the selected moni-
tor.
While the selected monitor is in the alarm mode status,
press the ALM RESET*
1(or RESET*2) button. All the alarms
occurred to the monitor will be reset, and the monitor dis-
play will return to the status before the alarm occurrence.
*
1WV-CU950/650
*2WV-CU360C/CJ
Note:Alarm monitor reset is also available by supplying
Alarm Recover Input signals to the unit. (Refer to p. 36.)
Alarm All Reset
You can reset all the alarms occurred to the system.
Press the ALM ALL RESET*
1(or ALL RESET*2) button while
holding down the SHIFT button. All the alarms occurred to
the system will be reset. 
						

							69
*1WV-CU950/650
*2WV-CU360C/CJ
Notes:
•Alarm all reset will also be conducted when setting
changes are performed in SETUP MENU or WJ-SX650
Series Administrator Console.
•To reset the alarms occurred to recorders, perform
alarm all reset. Alarm all reset is available even while no
alarms are occurring.
Return to Alarm Mode Status
You can recover from the ACK status to the alarm mode
status.
WV-CU950/650
Press the ACK button while holding down the SHIFT button. 
The alarm mode will be recovered.
WV-CU360C/CJ
This operation is not available.
Alarm Suspension
You can suspend the system from accepting alarm input
signals when you do not want to be disturbed. (Alarm will
also be suspended for recorders.)
1. Press the ALM SUSPEND*
1(or SUSPEND*2) button
while holding down the SHIFT button. 
The alarm will be suspended.
2.
To cancel the alarm suspension mode, press the ALM
SUSPEND*1(or SUSPEND*2)button while holding down
the SHIFT button again.
*1WV-CU950/650
*2WV-CU360C/CJ
Alarm History Display
The latest 1 000 alarm records (date, time and details) can
be displayed as the alarm history on an active monitor.
Note:Alarm History Display is not available on monitors in
the alarm mode or during recorder selection.
WV-CU950/650
Press the ALM RECALL button. The Alarm History Display
will appear on the selected monitor.
WV-CU360C/CJ
Press the OSD and ALM H buttons at a time. The Alarm
History Display will appear on the selected monitor.
Details on Alarm History Display
∗ beside the time indicates daylight saving time (sum-
mer time).
The following items are display details.
• ALARM (Highlighted for reset alarms)
T-001 to 256:Terminal alarm
(Example: For T-001, 001 means the number of
alarm input signal accepted by the ALARM IN port
of video input board.)
C-001 to 999:Camera alarm
(Example: For C-001, 001 means the number of
camera supplying an alarm input signal to the unit.)
R-001 to 999:Recorder alarm
(Example: For R-001, 001 means the number of
camera associated with the recorder supplying an
alarm input signal to the unit.)
S-0001 to 1024:Serial alarm
(Example: For S-0001, 0001 means the serial com-
mand alarm input number.)
V-001 to 999:Video loss
(Example: For V-001, 001 means the number of
camera to which video loss has occurred)
ALL:Alarm all reset
:Alarm suspension ON/OFF
S
    ALARM HISTORY                1 of 100
 M  D  Y  H  M  S  ALARM     ACTION   REC
Aug31/06
∗11:59:00PM ALL       12345   K4-8
Aug31/06∗11:58:00PM C-999     M32 C100 001
Aug31/06∗11:57:00PM V-001     M03 T32  256
Aug31/06∗11:56:00PM           POWER
Apr15/05∗09:15:25AM                      POWER
Apr15/05∗09:15:25AM R-003
Apr15/05∗09:13:54AM S-0002    M10*G32  ———
Apr15/05∗09:12:32AM T-001     M20 ———  999
Jan02/05 03:05:10PM S         56789    PC
Jan01/05 03:04:08PM S         101      PSD
T-TERMINAL  C-CAMERA         R-RECORDER
S-SERIAL    V-VIDEO LOSS     SSUSPEND 
						

							70
• ACTION
POWER:The unit is powered on. (Highlighted: Power
off) 
M01 to 32:Alarm occurred to Monitor 1 to 32. (For
group sequence and group preset, the smallest
monitor number is displayed with ∗.)
C001 to C999:Camera 001 to Camera 999 was activat-
ed for spot mode.
T01 to 32:Tour Sequence 1 to 32 was activated.
G01 to 32:Group sequence (or Group preset) 1 to 32
was activated.
Notes:
•User ID and Controller information is displayed for
an alarm reset or suspended by an operator. (They
are not displayed for auto reset.)
•User ID and controller No. will be highlighted to
indicate alarm reset or alarm suspension OFF.
• REC
Recording Source (LCN) associated with the alarm event
is displayed.
Refer to p. 73 Lists of Operations and Functions for opera-
tions while the Alarm History Display is displayed on the
monitor.