Panasonic Matrix Switcher Wj Sx650p Operating Instructions

11
RESET No.MODE
qw e
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
EXTENSION  3  INEXTENSION  2  IN
4
MODERS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3IN C-3 board
IN X-2 board
IN X-1 boarduu
i
!0
!1
4
3
MODERS485 (CAMERA) RS485 (CAMERA)MODE MODE MODE
21
IN B-3
MODERS485 (CAMERA) RS485 (CAMERA)MODE MODE MODE
4
321
EXTENSION 1TERM.
OFF
ON
OUTIN
IN A-3EXTENSION  3  OUTEXTENSION  2  OUTIN...

12
Video Output Board WJ-PB65M16
Video output board is composed of a main board (installed into the front side) and rear boards (x 3)(installed into the rear
side).
Front View
qOutput Mode Selection Switches (MODE)
Refer to p. 18 Switch Settings for Video Output Main
Board for details.
wReset Switch (RESET)
This button is used only for factory tests. Do not press. 
Rear View
OUT X-3 board
rExtension Ports 1 (EXTENSION 1: IN, OUT)
These ports connect to an optional card cage.
tTermination Selector...

13
Monitor Display Information
The following are the details on terminal mode operations. For PS·Data operations, refer to p. 85 OPERATION (OTHER THAN
TERMINAL MODE) or the operating instructions of system controllers. 
qTime and Date Information
Current time and date are displayed.
During daylight saving time (summer time), ∗ is dis-
played beside the time. 
Example:Aug/02/2005 ∗20:15:56
Note:While a recorder is being selected, time and date
are not displayed.
wMonitor Status Information
Monitor...

14
Notes:
• During the alarm acknowledgement (ACK) status (refer
to p. 68), event information is highlighted.
• When two or more alarm events have occurred, ∗ is
displayed beside the event information.
• When an alarm whose display mode setting is OFF
occurs, # is displayed beside the event information.
• When auto tracking is scheduled for a camera event, #
is displayed beside the camera number.
•qto rcan be displayed or hidden either altogether or
separately. Refer to p. 73 Lists of Operations and...

15
 WV-CU360C/CJ
qMonitor number
01 to 32:Monitor number
wCamera/recorder/sequence number
001 to 999:Camera number
H01 to 16:Recorder number
t01 to 32:Tour sequence number
r01 to r08:Group sequence number
Note:During sequence pause, P is displayed instead
of t and r.
r09 to 32:Group preset number
Note:This sign disappears when the camera is con-
trolled.
eEvent 
The following signs appear to indicate events on the
LED display.
A0001 to 0256 (Blinking):Terminal alarm
A0001 to 0999 (Blinking):Camera alarm...

16
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
The following is the installation flow of this unit.
•Checking Board Composition
•Switch Settings for Video Input Main Board (Refer to p. 17.)
•Switch Settings for Video Output Main Board (Refer to p. 18.)
•Mounting Video Input and Output Boards (Refer to p....

17
Switch Settings for Video Input Main Board
With the switch settings of main boards, board numbers are given to all video input boards. To give the board number to each
board, rotate the Unit No. switch on the main board.
Notes: 
• The board number setting must be different from each other.
• 8, 9, and A to F are reserved settings. They cannot be set for board numbers.
RESET No.MODE
Board number switch
0123456789ABCDEF
Board number Switch setting
10
21
32
43
54
65
87 76 

18
Switch Settings for Video Output Main Board
When mounting an additional video input board, up to 32 monitors can be connected to the unit.
Front view of video output main board
To identify Video Output Board 1 from Video Output Board 2, set the MODE switches (SW4004) and sliding switches (SW1,
SW2, SW3, SW4, and SW4006) as follows.
Note:If the unit has only one Video Output Board, be sure to apply switch settings of Video Output Board 1. When the switch
settings are incorrect, the unit may not work...

19
Mounting Video Input and Output Boards
To use additional video input or output boards, mount these boards into the expansion slots of the unit after checking the
board composition and performing switch settings (refer to pp. 16 to 18). The following is the figures describing recommended
board composition. 
Notes:
• Refer to p. 20 for how to mount these boards.
• Video Output Board 1 and 2 must be mounted into the same unit.
• Refer to p. 26 for how to connect card cages. 
Type 1
Not used
Video Input...

20
Board Mounting Procedure
The following example is the procedure to mount a set of
video input board into the expansion slot of the unit.
Note:Before the procedure, power off the unit.
1. Remove the expansion slot panel from the rear side.
2. Mount the rear boards into the expansion slot, and fix
these boards with screws supplied to the rear boards.
Notes:
• The board name (IN X-1, OUT X-1, etc.) is marked at
the lower right corner of each board mounting angle.
When mounting the rear boards, match the...