Panasonic Matrix Switcher Wj Sx650p Operating Instructions

31
LCN LCN
1 to 16
17 to 32
33 to 48
49 to 64
65 to 80
81 to 96
97 to 112
113 to 128Recorder number (Unit Address (System)) Recorder number (Unit Address (System))
1
2
3
4
5
6
7
8129 to 144 9
145 to 160 10
161 to 176
177 to 19211
12
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
EXTENSION  3  INEXTENSION  2  IN
4
MODERS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3
Unit Address (System): 1• •...

32
Recorder number (Unit Address (System))
VIDEO OUT 3
VIDEO OUT 4
VIDEO OUT 2IN X-2VIDEO OUT 1ALARM IN
IN X-116 32
15 31 30
14 1329 28
12 1127 26
10 925CAMERA IN
24
8723 22
6521 20
4319 18
2117
EXTENSION  3  INEXTENSION  2  IN
4
MODERS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3
BNC cable D-sub/BNC Video Cable WJ-CA68 
32 31 30 25 24 17 16 9 8 1
RecorderRecorder
Video input signals are supplied from 
recorders to the CAMERA IN 31 and 32.
Video input 
board
LCN: 17 to 32
Unit Address (System):...

33
1 2
IN
OUTCASCADE
OUT
16 16 315 1514
1413
2 113
12 1211
1110
109
98
87
76
65
54
43
32
21
1VIDEO
AUDIO IN AUDIO OUTMONITOR OUT CASCADE INMONITOR (VGA) ALARM/CONTROLSERIAL ALARMPOWER COPY 1 MODEEXT STORAGE 10/100BASE-T RS485(CAMERA)D ATAAC  IN
SIGNAL GND1
42
1 2
IN
OUTCASCADE
OUT
16 16 315 1514
1413
2 113
12 1211
1110
109
98
87
76
65
54
43
32
21
1VIDEO
AUDIO IN AUDIO OUTMONITOR OUT CASCADE INMONITOR (VGA) ALARM/CONTROLSERIAL ALARMPOWER COPY 1 MODEEXT STORAGE 10/100BASE-T RS485(CAMERA)D ATAAC  IN
SIGNAL...

34
Recorder Settings
Be sure to perform the settings for connected recorders in
SETUP MENU of recorders.
You can set wto tafter connections. However, you must
set qseparately for each recorder before connections. The
settings are performed in SETUP MENU (Advanced) of
each recorder.
qUnit Address (System) 
Set the Unit Address (System) for each recorder in
Comm – PS.Data Setup. 001 to 016 are available.
(Up to 16 recorders can be connected.) The unit
address setting must be different from each other....

35
PS·Data Mode Connection
To apply the PS·Data mode, connect the system controllers
as follows.
1. Connect the system controllers to the DATA 1 port of
Video Output Board 1.
Notes:
•In the factory default, the DATA 1 port is set for the ter-
minal mode connection. To apply the PS·Data mode
connection, perform the DATA port settings in DATA
PORT of SETUP MENU (refer to p. 52) or System –
DATA Port of WJ-SX650 Series Administrator Console.
•Both of terminal mode and PS·Data system controllers
cannot be...

36
Alarm Sensor Connections
Alarm input signals can be supplied by alarm sensors con-
nected to the ALARM IN port at the video input board. The
following are the ALARM IN port details.
Notes:
•
Perform the setting of each signal polarity in TERMINAL ALARM
of SETUP MENU (refer to p. 50) or Alarm – Alarm Mode –
Terminal Setup of WJ-SX650 Series Administrator Console.
•Perform the setting of each alarm event in Alarm –
Alarm Event of WJ-SX650 Series Administrator Console.
External Device Connections
With...

Time Adjust Input Time Adjust Output
37
Terminal Duration Remarks
Alarm Output 1 to
32Until reset Open Collector output,
24 V, 100 mA maximum
Alarm Recover
Input 1 to 16100 or more
msNon-voltage make con-
tact output
1 second• Open Collector out-
put, 24 V, 100 mA
maximum
• Signal is output every
hour on the hour.
100 or more
ms• Non-voltage make
contact input
• Signal input is accept-
ed by up to ± 30 sec-
onds every hour on
the hour.
Time is adjusted on
the hour.
Note:Alarm Recover Input 1 to 16 can be...

38
Before operation, setup of this unit is required. Setup is per-
formed from WJ-SX650 Series Administrator Console installed
on a PC. (Some settings are available from SETUP MENU of
this unit.) The following is an example of setup procedure.
Notes:
•Setup may differ depending on system composition.
(Settings of Step 1 and 4 in the following procedure
must be performed.)
•For Step 2, 3, 5 and 6 in the following setup procedure,
the factory default can be maintained.
Example: camera x 150, recorder x 10,...

39

VD2/DATA/CABLE COMPENSATION (Refer to p. 53.)
5. Perform the RS-485 camera settings.
CAM001 to 150:If you use RS-485 cameras, select
desired parameters for the RS-485 (CAMERA) ports
and camera unit numbers.

System – VD2/DATA/Cable Comp. – RS485 Camera

RS485 CAMERA (Refer to p. 53.)
6. Perform the settings of cameras supplying video input
signal to recorders.

Recorder – LCN Setting (CAM 1 to 16):Set the LCNs
of camera input connectors used for the loop-thru
connections between the recorders and the...

40
This chapter explains about WJ-SX650 Series Administrator
Console. Before controlling WJ-SX650 Series Administrator
Console, installation on the PC is required.
System Requirements of a PC
To install WJ-SX650 Series Administrator Console, the PC
should meet the following requirements.
OS:
One of the following operating systems:
Microsoft
®Windows®2000 Professional SP4
Microsoft®Windows®XP Professional SP2
Microsoft®Windows®XP Home Edition SP2 
Note:To work WJ-SX650 Series Administrator Console on
the...