Panasonic LCD Projector Pt Rz670 Operating Instructions

							Chapter 4 Settings — [POSITION] menu
ENGLISH - 81
6) Press qw to adjust.
Note
 f When [ASPECT] is set to [THROUGH], [ZOOM] cannot be adjusted.
When [ASPECT] is set to [DEFAULT]
1) Press  as to select [ZOOM].
2)  
Press the  button.
 f The  [ZOOM]  screen is displayed.
3) Press  as to select [MODE].
4)  
Press 
 qw to switch the item.
[INTERNAL] Enlarges the size within the aspect range set with [SCREEN FORMA T].
[FULL] Enlarges or reduces the size using the entire display area set with [SCREEN FORMA T].
5) Press as to select [INTERLOCKED].
6)  
Press 
 qw to switch the item.
[OFF] Sets the [VERTICAL] and [HORIZONTAL] zoom ratio.
[ON] Uses [BOTH] to set zoom ratio. Image can be enlarged or reduced vertically and horizontally at the 
same magnification.
7) Press 
as to select [VERTICAL] or [HORIZONTAL].
 fIf [ON] is selected, select [BOTH].
8) Press  qw to adjust.
Note
 f When [ASPECT] is not set to [DEF AULT], [MODE] is not displayed.
[CLOCK PHASE]
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1) Press as to select [CLOCK PHASE].
2)  
Press 
 qw or the  button.
 fThe  [CLOCK PHASE] individual adjustment screen is displayed.
3) Press  qw to adjust.
 fAdjustment value will change between [0] and [+31].  Adjust so that the amount of interference is at a minimum.
Note
 fSome signals may not be adjusted. fOptimal value may not be achieved if the output from the input computer is unstable. fOptimal value may not be achieved when there is a shift in the total dot numbers. f[CLOCK PHASE] can be adjusted only when a signal is input to the  terminal or the  terminal. f[CLOCK PHASE] cannot be adjusted when a digital signal is input. fIf you press 

w while the adjustment value is [+31], the value will become [0]. If you press  q while the adjustment value is [0], the value will 
become [+31].
[GEOMETRY]
(Only for PT- RZ670)
You can correct various types of distortion in a projected image.
Unique image processing technology enables projection of a square image on a special screen shape.
1) Press  as to select [GEOMETRY].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Does not perform geometric adjustment.   
						

							Chapter 4 Settings — [POSITION] menu
82 - ENGLISH
[KEYSTONE]Adjusts any trapezoidal distortion in the projected image.
[CORNER CORRECTION] Adjusts any distortion in the four corners of the projected image.
[CURVED] Adjusts any curved distortion in the projected image.
[PC-1]
*1
Uses the computer to perform geometric adjustment.
[PC-2]*1
[PC-3]*1
*1 Advanced skills are necessary to use a computer to control geometric adjustment. Consult your dealer . Up to three geometric adjustments 
performed using the computer can be saved.
Setting [KEYSTONE] or [CURVED]
1) Press  as to select [GEOMETRY].
2)  
Press 
 qw to select [KEYSTONE] or [CURVED].
3)
 
Press the  button.
 f The  [GEOMETRY:KEYSTONE] or [GEOMETRY:CURVED] screen is displayed.
4) Press  as to select the item to adjust.
5)  
Press 
 qw to adjust.
[KEYSTONE]
[LENS THROW RATIO]
Set the throw ratio for the lens used.
[VERTICAL KEYSTONE]
[HORIZONTAL KEYSTONE]
[VERTICAL BALANCE][HORIZONTAL BALANCE]
Adjust the setting according to the lens shift range in the vertical 
direction. Adjust the setting according to the lens shift range in the horizontal 
direction.
[CURVED]
[LENS THROW RATIO]
Set the throw ratio for the lens used.
[VERTICAL KEYSTONE]
[HORIZONTAL KEYSTONE]
[VERTICAL ARC][HORIZONTAL ARC]   
						

							Chapter 4 Settings — [POSITION] menu
ENGLISH - 83
[CURVED]
[VERTICAL BALANCE]
[HORIZONTAL BALANCE]
[MAINTAIN ASPECT RATIO]
Select [ON] to correct while keeping the aspect ratio.
Setting [CORNER CORRECTION]
1) Press  as to select [GEOMETRY].
2)  
Press 
 qw to select [CORNER CORRECTION].
3)
 
Press the  button.
 f The  [GEOMETRY:CORNER CORRECTION] screen is displayed.
4) Press  as to select the item to adjust, and press the  button.
5)  
Press 
 asqw to adjust.
[CORNER CORRECTION]
[UPPER LEFT]
[UPPER RIGHT][LOWER LEFT][LOWER RIGHT]
[LINEARITY]
Horizontal direction
Vertical direction
Note
 f If [EDGE BLENDING] ( x   page   87) adjustment and [GEOMETRY] are used together, correct edge blending adjustment may not be 
possible in certain environments.
 f The optional Upgrade Kit (Model No.: ET-

UK20) can be used to expand the correctable range. To purchase the product, consult your dealer.
 fThe image may disappear for a moment while performing adjustment, but it\
 is not a malfunction.   
						

							Chapter 4 Settings — [POSITION] menu
84 - ENGLISH
[KEYSTONE]
(Only for PT-RW630)
You can correct the keystone distortion that occurs when the projector is installed tilted or when the screen is tilted.
1) Press  as to select [KEYSTONE].
2)  
Press the  button.
 f The  [KEYSTONE] screen is displayed.
3) Press  as to select the item to adjust.
4)  
Press 
 qw to adjust.
[KEYSTONE] [SUB KEYSTONE]
[LINEARITY]
Note
 fThe menu or logo may run of f the screen when adjustments are performed with [KEYSTONE]. fCorrecting up to ±40° for the tilt in the vertical direction is available for adjustments with [KEYST ONE]. However
, the image quality 
will degrade and it will get harder to focus with more correction. Insta\
ll the projector so that the correction will be as small as possible. 
(Correcting up to ±30° is possible when the fixed-focus lens (Model No.: ET
-

DLE055) or ultra short focus zoom lens (Model No.: 
ET
-

DLE085) is used. Correcting up to 5° to the direction that the projector and screen are to be distant is possible when the fixed-focus lens 
(Model No.: ET
-

DLE030) is used.)
 fScreen size will also change when [KEYST

ONE] is used to perform various adjustments.
 fWhen the keystone distortion is corrected with [KEYST

ONE], the edge blending cannot be adjusted together.
 fAspect ratio of the image size may shift depending on the correction or lens zoom value. fFor the portrait setting, keystone is corrected for horizontal tilt.   
						

							Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 85
[ADVANCED MENU] menu
On the menu screen, select [ADVANCED MENU] from the main menu, and select an item from 
the sub-menu.
Refer to “Navigating through the menu” (x
  page   67) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to adjust.
[DIGITAL CINEMA REALITY]
You can increase the vertical resolution and enhance the image quality by performing cinema processing when the PAL (or SECAM) 576i 
signal, the NTSC 480i signal, and 1080/50i, 1080/60i are input.
1) Press  as to select [DIGITAL CINEMA REALITY].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Performs automatic detection and cinema processing. (Factory default)
[OFF] Does not perform cinema processing.
[30p FIXED] During 480i or 1080/60i signal 
input
Performs forced cinema processing (2:2 pulldown).
[25p FIXED] During 576i or 1080/50i signal 
input
Note
 f
In [DIGITAL CINEMA REALITY], the picture quality will degrade when a signal other than the 2:2 pulldown is set as [25p FIXED] or [30p 
FIXED]. (Vertical resolution will degrade.)
 f When [FRAME RESPONSE] is set to [F

AST], [DIGITAL CINEMA REALITY] cannot be set.
[BLANKING]
You can adjust the blanking width if there are noises at the edge of the screen or the image is slightly running out from the screen while an 
image from the VCR or other devices are projected.
1) Press as to select [BLANKING].
2)  
Press the  button.
 f The  [BLANKING] adjustment screen is displayed.
3) Press  as to select [UPPER], [LOWER], [LEFT], or [RIGHT].
 fWhen [CUST OM MASKING] is set to an item other than [OFF] ([PC-1], [PC-2], or [PC-3]), the blanking width can be adjusted to any 
shape using the computer. Up to three blanking settings adjusted using the computer can be saved. (Only for PT- RZ670)
To use the [CUSTOM MASKING] function, the optional Upgrade Kit (Model No.: ET
-

UK20) is required. To purchase the product, 
consult your dealer.
4) Press  qw to adjust the blanking width.   
						

							Chapter 4 Settings — [ADVANCED MENU] menu
86 - ENGLISH
Blanking correctionItem Operation AdjustmentRange of adjustment
Top of the screen [UPPER] Press q.
The blanking zone 
moves upward.
PT-
RZ670: Top to bottom 
0 - 599
PT
-

RW630: Top to bottom  0 - 399
Press w.
The blanking zone 
moves downward.
Bottom of the  screen [LOWER]Press w.
The blanking zone 
moves upward.
Press q.The blanking zone 
moves downward.
Left side of the  screen [LEFT]Press w.
The blanking zone 
moves to the right.
PT-
RZ670: Left to right 
0 - 959
PT
-

RW630: Left to right  0 - 639
Press q.
The blanking zone 
moves to the left.
Right side of the  screen [RIGHT]Press q.
The blanking zone 
moves to the right.
Press w.The blanking zone 
moves to the left.
[INPUT RESOLUTION]
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1) Press 
as to select [INPUT RESOLUTION].
2)  
Press the  button.
 f The  [INPUT RESOLUTION]  screen is displayed.
3) Press as to select [TOTAL DOTS], [DISPLAY DOTS], [TOTAL LINES], or [DISPLAY LINES], and press 
qw to adjust each item.
 f Values corresponding to the signal being input are displayed automaticall\
y for each item. Increase or decrease the displayed values 
and adjust to the optimal point viewing the screen when there are vertic\
al stripes or sections are missing from the screen.
Note
 f Previously mentioned vertical banding will not occur with all white sign\
al input. fThe image may be disrupted while performing the adjustment, but it is no\
t a malfunction. f[INPUT

 RESOLUTION] can be adjusted only when an RGB signal is input to the  terminal or the  terminal.
 fSome signals may not be adjusted.
[CLAMP POSITION]
You can adjust the optimal point when the black part of the image is blunt or it has turned green.
1) Press  as to select [CLAMP POSITION].
2)  
Press 
 qw to adjust.
Status Rough guide for optimal value Range of adjustment
The black part is blunt. The point where bluntness of the black part improves the most is 
the optimal value.
1 - 255
The black part is green. The point where the green part becomes black, and the bluntness 
has improved is the optimal value.
Note
 f
[CLAMP POSITION] can be adjusted only when a signal is input to the  terminal or the  terminal. fSome signals may not be adjusted.   
						

							Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 87
[EDGE BLENDING]
The edge blending function allows multiple projector images to be seamle\
ssly overlapped by using the inclination of the brightness at the 
overlapped area.
1) Press as to select [EDGE BLENDING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Sets the edge blending function to off.
[ON] Use the setting value preset in the projector for the inclination of the edge blending area.
[USER] Use the user-setting value for the inclination of the edge blending area. (Configuration/registration 
requires separate software. Consult your dealer.)
 f
T

o adjust edge blending, proceed to Step  3).
3) When [ON] or [USER] is selected, press the  button.
 fThe  [EDGE BLENDING] screen is displayed.
4) Press  as to specify the location to be corrected.
 fWhen joining at top: Set [UPPER] to [ON]
 fWhen joining at bottom: Set [LOWER] to [ON]
 fWhen joining at left: Set [LEFT] to [ON]
 fWhen joining at right: Set [RIGHT] to [ON]
5) Press  qw to switch to [ON].
6)  
Press 
 as to select [START] or [WIDTH].
7)
 
Press 
 qw to adjust the starting position or correction width.
8)
 
Press 
 as to select [MARKER].
9)
 
Press 
 qw to switch to [ON].
 fA marker for image position adjustment is displayed. The position where the red and green lines overlap for the projectors to be joined 
will be the optimal point. Make sure to set the correction width for the projectors to be joined with the same value. Optimal joining is not 
possible with projectors that have different correction widths.
The optimal point is the point at which these lines overlap.
Green lineRed line
10) Press  as to select [BRIGHTNESS ADJUST].
11)  
Press the  button.
 fThe  [BRIGHTNESS ADJUST] screen is displayed.
 fBy setting [AUT

O TESTPATTERN] on the [EDGE BLENDING] screen to [ON], the black test pattern is displayed when you enter the 
[BRIGHTNESS ADJUST] screen.
12) Press  as to select [NON-OVERLAPPED BLACK LEVEL].
13)  
Press the  button.
 fThe  [NON-OVERLAPPED BLACK LEVEL] screen is displayed.
 fIf [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE] can be adjusted individually .
14) Press as to select an item, and press qw to adjust the setting.
 fOnce the adjustment is completed, press the  button to return to the  [BRIGHTNESS ADJUST]  screen.   
						

							Chapter 4 Settings — [ADVANCED MENU] menu
88 - ENGLISH
15) Press as to select [UPPER], [LOWER], [LEFT], or [RIGHT] in [BLACK BORDER WIDTH].
16)  
Press 
 qw to set the region (width) of the [BLACK BORDER WIDTH] adjustment.
 fWhen PT- RZ670 is used, proceed to Step  17).
 fWhen PT-

RW630 is used, proceed to Step  19).
17) Press as to select [UPPER KEYSTONE AREA], [LOWER KEYSTONE AREA], [LEFT KEYSTONE 
AREA], or [RIGHT KEYSTONE AREA].
18)
 
Press 
 qw to adjust the tilt of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK 
BORDER LEVEL].
19)
 
Press 
 as to select [BLACK BORDER LEVEL].
20)
 
Press the  button.
 fThe  [BLACK BORDER LEVEL] screen is displayed.
 fIf [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE] can be adjusted individually .
21) Press as to select an item, and press qw to adjust the setting.
[BLACK BORDER WIDTH] (Right)
Projection range Edge blending [WIDTH] (Right)
[MARKER] (Red)Edge blending [START] (Right)
([MARKER] (Green))
[BLACK BORDER LEVEL] [OVERLAPPED BLACK LEVEL] (Right)
[NON-OVERLAPPED BLACK LEVEL]
Note
 f [BRIGHTNESS  ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to 
notice when [EDGE BLENDING] is used to configure multiple screens.  The optimal amount of correction can be set by adjusting [NON-
OVERLAPPED BLACK LEVEL] so that the black level of the overlapping image area will be the same as that of the non-overlapping area. 
If the border area between the image overlapping part and non-overlapping part gets brighter after adjusting [NON-OVERLAPPED BLACK 
LEVEL], adjust the width of the top, bottom, left, or right. Adjust [BLACK BORDER LEVEL] when the width adjustment makes only the 
border area darker.
 f The joining 

part may look discontinuous depending on the position you are looking from when a screen with high gain or rear screen is used.
 fWhen configuring multiple screens using both horizontal and vertical edge blending, adjust [OVERLAPPED BLACK LEVEL] first before 
making adjustments in Step  12)

. Adjustment method is the same as the procedure of [NON-OVERLAPPED BLACK LEVEL].
 fIf only horizontal or only vertical edge blending is used, set all items in [OVERLAPPED BLACK LEVEL] to 0. f[AUT

O TESTPATTERN] settings change together with the [AUTO TESTPATTERN] of [COLOR MATCHING].
 fAdjustment of the tilt of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK BORDER LEVEL] is a function to perform 
edge blending together with the adjustment of [GEOMETR

Y] (x   page   81). If [NON-OVERLAPPED BLACK LEVEL] is tilted by correcting 
the keystone distortion with [KEYSTONE] in [GEOMETRY], perform Steps 17) 18) to adjust the edge blending according to the shape of 
[NON-OVERLAPPED BLACK LEVEL].
 f When the keystone distortion is corrected with [KEYST

ONE], the edge blending cannot be adjusted together. (Only for PT
-
 RW630)
[FRAME RESPONSE]
Set image frame delay.
1) Press as to select [FRAME RESPONSE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL] Standard setting.
[FAST]
*1Simplifies the image processing to reduce image frame delay.
[FIXED]
*2Sets image frame delay to be constant regardless of the image position or magnification.
*1 When input signals are other than interlaced signals, [F AST] cannot be set.
*2  
Only when movie-based signals and still image signals with the vertical scanning frequency of 50
   Hz or 60   Hz are input
Note
 fWhen [FRAME RESPONSE] is set to [F AST], picture quality deteriorates. Also, [DIGITAL CINEMA REALITY] cannot be set. f[FRAME RESPONSE] cannot be set during P
 IN P.   
						

							Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 89
[RASTER POSITION]
This will allow the position of the image to move within the display are\
a arbitrarily when the input image is not using the whole display area.
1) Press as to select [RASTER POSITION].
2)  
Press the  button.
 f The  [RASTER POSITION]  screen is displayed.
3) Press asqw to adjust the position.   
						

							Chapter 4 Settings — [DISPLAY LANGUAGE] menu
90 - ENGLISH
[DISPLAY LANGUAGE] menu
On the menu screen, select [DISPLAY LANGUAGE] from the main menu, and display the sub-
menu.
Refer to “Navigating through the menu” (x
  page   67) for the operation of the menu screen.
 fPress 

as to select a language, and press the  button to set.
Changing the display language
You can select the language of the on-screen display.
ENTER
DISPLAY LANGUAGE
SELECT
SET
 fVarious menus, settings, adjustment screens, control button names, etc., \
are displayed in the selected language.
 fThe language can be changed to English, German, French, Spanish, Italian, Portuguese, Japanese, Chinese, Russian, or Korean.
Note
 fThe on-screen display language of the projector is set to English by default as well as when [ALL  USER DA TA] (x   page   124) in 
[INITIALIZE] is executed.