Panasonic LCD Projector Pt Rz670 Operating Instructions

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 131
[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   67) for the operation of the menu screen.
 fWhen the projector is used for the first time
Initial password: Press  awsqawsq in order

, and press the  button.
 fAfter selecting the item, press 

asqw to set.
Attention
 fWhen you select the [SECURITY] menu and press the  button, entering a password is required. Enter the preset password and 
then continue operations of the [SECURITY] menu.
 fWhen the password has been changed previously

, enter the changed password, and press the  button.
Note
 fThe entered password is displayed with*marks on the screen. fAn error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.
[SECURITY PASSWORD]
Display the  [SECURITY PASSWORD] screen when the power is turned on with the  switch set to the  side. When 
the entered password is incorrect, the operation will be restricted to t\
he power standby < v> button, the  button, and the  
(, , ) buttons.
1) Press  as to select [SECURITY PASSWORD].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the security password entry.
[ON] Enables the security password entry.
Note
 fThe [SECURITY  PASSWORD] setting is set to [OFF] by the factory default or when [ALL USER DATA] in [INITIALIZE] ( x   page   124) is 
executed.
 f Change the password periodically that is hard to guess. fThe security password is enabled after setting [SECURITY

 PASSWORD] to [ON] and turning the  switch to .
[SECURITY PASSWORD CHANGE]
Change the security password.
1) Press as to select [SECURITY PASSWORD CHANGE].
2)  
Press the  button.
 f The  [SECURITY PASSWORD CHANGE] screen is displayed.
3) Press  asqw and the number ( - ) buttons to set the password.
 fUp to eight button operations can be set.
4) Press the  button.
5)  
Re-enter the password for the confirmation.
6)

 
Press the  button.   
						

							Chapter 4 Settings — [SECURITY] menu
132 - ENGLISH
Note
 fThe entered password is displayed with*marks on the screen. fWhen numerical values are used for the security password, the security p\
assword is required to be initialized if the remote control is lost. 
Consult your dealer for the method of initialization.
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1) Press  as to select [DISPLAY SETTING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] The text display is disabled.
[TEXT] The text display is enabled.
[USER LOGO] Displays the image registered by the user.
Note
 fTo create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[TEXT CHANGE]
Change the text displayed when the text display is enabled by selecting [TEXT] in [DISPLA Y SETTING].
1) Press as to select [TEXT CHANGE].
2)  
Press the  button.
 f The  [TEXT CHANGE] screen is displayed.
3) Press  asqw to select the text, and press the  button to enter the text.
4)  
Press 
 asqw to select [OK], and press the  button.
 fThe text is changed.
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote\
 control.
1) Press  as to select [CONTROL DEVICE SETUP].
2)  
Press the  button.
 f The  [CONTROL DEVICE SETUP] screen is displayed.
3) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
[CONTROL PANEL] You can set the limitation on the control from the control panel.
[REMOTE CONTROL] You can set the limitation on the control from the remote control.
4) Press the  button.
 fThe  [CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)  
Press 
 qw to switch the item.
 fYou can set the operation restriction from the control panel or the remote control.
[ENABLE] Enables all button operations.
[DISABLE] Disables all button operations.
[USER] Operation of all buttons can be enabled/disabled separately.
Refer to “Enabling/disabling any button” (
x
  page   133) for details.
7) Press as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
8) Press  qw to select [OK], and press the  button.   
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 133
Enabling/disabling any button
1) Press as to select [CONTROL DEVICE SETUP].
2)  
Press the  button.
 f The  [CONTROL DEVICE SETUP] screen is displayed.
3) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
4)  
Press the  button.
5)

 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)
 
Press 
 qw to switch [USER].
7)
 
Press 
 as to select the button item to set.
 fWhen [INPUT  SELECT BUTTON] is selected, press the  button, and then press as to select the button to set.
Buttons that can be set
[CONTROL PANEL] [REMOTE CONTROL]
[POWER BUTTON] Power standby  button, power on  button
[INPUT SELECT BUTTON]  button,  button,  
button,  button,  button, 
 button
*1
 button,  button,  
button,  button,  button, 
 button
*1
[MENU BUTTON]
 button
[LENS BUTTON]  button Lens (, , ) button
[AUTO SETUP BUTTON]  button
[SHUTTER BUTTON]  button
[ON SCREEN BUTTON] — button
[OTHER BUTTON] asqw,  button Buttons not listed above
*1 SDI input is supported only for PT-
RZ670.
8) Press qw to switch the item.
[ENABLE] Enables button operations.
[DISABLE] Disables button operations.
 fThe following items are available only when [RGB1/2 BUTT

ON] of [INPUT SELECT BUTTON] is selected.
[TOGGLE]Switches between [RGB1] and [RGB2] when the button is operated.
[RGB1] Fixes to [RGB1].
[RGB2] Fixes to [RGB2].
[DISABLE] Disables button operations.
 fThe following items are available only when [VIDEO BUTT

ON] of [INPUT SELECT BUTTON] is selected.
[DISABLE]Disables button operations.
[VIDEO] Fixes to [VIDEO].
[Y/C] Fixes to [Y/C].
[TOGGLE] Switches between [VIDEO] and [Y/C] when the button is operated.
 fWhen [INPUT

 SELECT BUTTON] is selected in Step 7), after the item is switched, press the  button to return to the 
[CONTROL PANEL] screen or the [REMOTE CONTROL]  screen.
9) Press as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
10) Press  qw to select [OK], and press the  button.
Note
 f When a button operation is performed on the device set to [DISABLE], the  [CONTROL  DEVICE PASSWORD] screen is displayed.
Enter the control device password.
 f The 

[CONTROL DEVICE PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.
 fIf the operations of both [CONTROL

 PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 f When the setting has completed, the menu screen will disappear

. To operate continuously, press the  button to display the main 
menu.
 f Even when button operation on the remote control is disabled, operation of the  button on the remote control is enabled.   
						

							Chapter 4 Settings — [SECURITY] menu
134 - ENGLISH
[CONTROL DEVICE PASSWORD CHANGE]
The control device password can be changed.
1) Press as to select [CONTROL DEVICE PASSWORD CHANGE].
2)  
Press the  button.
 f The  [CONTROL DEVICE PASSWORD CHANGE]  screen is displayed.
3) Press asqw to select the text, and press the  button to enter the text.
4)  
Press 
 asqw to select [OK], and press the  button.
 fTo cancel, select [CANCEL].
Attention
 fThe initial password is “AAAA” by the factory default or when [ALL  USER DA TA] in [INITIALIZE] (x   page   124) is executed. fChange the password periodically that is hard to guess.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 135
[NETWORK] menu
On the menu screen, select [NETWORK] from the main menu, and select an item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   67) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[DIGITAL LINK MODE]
Switch the communication method of the  terminal of the projector.
1) Press  as to select [DIGITAL LINK MODE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Switches the communication method automatically to DIGITAL LINK or Ethernet.
[DIGITAL LINK] Fixes the communication method to DIGITAL LINK.
[ETHERNET] Fixes the communication method to Ethernet.
Possible communication modes
Setting Communication possible
Image transmission EthernetRS
- 232C
[AUTO] For DIGITAL LINK
lll
For Ethernet ―
l―
[DIGITAL LINK] lll
[ETHERNET] ―
l―
l: Communication possible
―: Communication not possible
[DIGITAL LINK SETUP]
Set the communication method of DIGITAL LINK or Ethernet.
When the projector is connected directly via Ethernet
1) Press  as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 f The  [DIGITAL LINK SETUP] screen is displayed.
3) Press  as to select [DUPLEX(ETHERNET)].
4)  
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[AUTONEGOTIATION] Sets the communication method automatically.
[100BaseTX-Full] Full-duplex communication method is set.
[100BaseTX-Half] Half-duplex communication method is set.
5) Press as to select [STORE].
6)  
Press the  button.   
						

							Chapter 4 Settings — [NETWORK] menu
136 - ENGLISH
7) When the confirmation screen is displayed, press qw  to select [OK], and press the  button.
Note
 f The projector does not support 10BaseT  Full/Half.
When the projector is connected to a twisted-pair-cable transmitter
1) Press as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 f The  [DIGITAL LINK SETUP] screen is displayed.
3) Press  as to select [DUPLEX(DIGITAL LINK)].
4)  
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[100BaseTX-Full] Full-duplex communication method is set.
[100BaseTX-Half] Half-duplex communication method is set.
[AUTONEGOTIATION] Sets the communication method automatically.
5) Press as to select [STORE].
6)  
Press the  button.
7)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[DIGITAL LINK STATUS]
Display the DIGITAL LINK connection environment.
1) Press as to select [DIGITAL LINK STATUS].
2)  
Press the  button.
 f The  [DIGITAL LINK STATUS] screen is displayed.
[LINK STATUS] Either [NO LINK], [DIGITAL LINK], or [ETHERNET] is displayed.
[HDCP STATUS] Either [NO SIGNAL], [OFF], or [ON] is displayed.
[SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to 
green, yellow, or red depending on that value.
Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter
.
 f[MAX]/[MIN]: Maximum/minimum value of the amount of error
 fGreen (-12 dB or lower)  →  Normal signal quality level
 fY

ellow (
-11 to -8 dB) → Warning level where there is the possibility of noise introduced on the 
screen
 f Red (-7 dB or higher) → Abnormal level where synchronization may be interrupted, or a signal may 
not be received
[NETWORK SETUP]
Perform the initial setting of the network before using the network func\
tion.
1) Press  as to select [NETWORK SETUP].
2)  
Press the  button.
 f The  [NETWORK SETUP] screen is displayed.
3) Press  as to select an item, and change the settings according to the operation instructions of the 
menu.
[PROJECTOR NAME] Allows to change the projector name. Enter the host name if it is required in such a case when you 
use a DHCP server.
[DHCP] [ON]
If a DHCP server exists in the network where the projector is to be 
connected, obtains the IP address automatically.
[OFF] If a DHCP server does not exist in the network where the projector 
is to be connected, set [IP ADDRESS], [SUBNET MASK], and 
[DEFAULT GATEWAY].   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 137
[IP ADDRESS]Enter the IP address when you do not use a DHCP server.
[SUBNET MASK] Enter the subnet mask when you do not use a DHCP server.
[DEFAULT GATEWAY] Enter the default gateway address when you do not use a DHCP server.
[STORE] Save the current network settings.
4) Press as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f When using a DHCP  server, confirm that the DHCP server is running. fConsult your network administrator regarding the IP
 address, subnet mask, and default gateway.
 fWhen [Art-Net SETUP] is set to [ON(2.X.X.X)] or [ON(10.X.X.X)], [NETWORK SETUP] cannot be selected.
[NETWORK CONTROL]
Set up the control method of the network.
1) Press  as to select [NETWORK CONTROL].
2)  
Press the  button.
 f The  [NETWORK CONTROL] screen is displayed.
3) Press  as to select an item, and press qw to change the setting.
[WEB CONTROL] Set to [ON] to control with the web browser.
[PJLink CONTROL] Set to [ON] to control with the PJLink protocol.
[COMMAND CONTROL] Set to [ON] to control with the / terminal control command format 
(x
  page   172). Refer to “Control commands via LAN” ( x
  page   167).
[COMMAND PORT] Set the port number used for command control.
[Crestron Connected(TM)] Set to [ON] to control with Crestron Connected
TM of Crestron Electronics, Inc.
[AMX D.D.] Set to [ON] to control with the controller of AMX Corporation.
Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, refer to 
the website of AMX Corporation.
URL http://www.amx.com/
[EXTRON XTP] Set to [ON] when connecting the “XTP transmitter” of Extron Electronics to the  
terminal.
The [EXTRON XTP] setting must be set to [OFF] when connecting the optional Digital Interface Box 
(Model No.: ET
-

YFB100G).
For details of the “XTP transmitter”, refer to the website of Extron Electronics.
URL http://www.extron.com/
[STORE] Save the current network control settings.
4) Press as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[NETWORK STATUS]
Display the status of the projector network.
1) Press as to select [NETWORK STATUS].
2)  
Press the  button.
 f The  [NETWORK STATUS] screen is displayed.
[DHCP] Displays the status of use of the DHCP server.
[IP ADDRESS] Displays the [IP ADDRESS].
[SUBNET MASK] Displays the [SUBNET MASK].
[DEFAULT GATEWAY] Displays the [DEFAULT GATEWAY].
[DNS1] Displays the address of the primary DNS server.
[DNS2] Displays the address of the secondary DNS server.
[MAC ADDRESS] Displays the [MAC ADDRESS].   
						

							Chapter 4 Settings — [NETWORK] menu
138 - ENGLISH
[DIGITAL INTERFACE BOX]
When the optional Digital Interface Box (Model No.: ET-YFB100G) is connected to the  terminal, the main menu of 
ET- YFB100G is displayed. Refer to the Operating Instructions of ET- YFB100G for details.
Note
 fWhen [EXTRON XTP] is set to [ON], [DIGIT AL INTERFACE BOX] cannot be selected. fThe operation guidance for the “RETURN” button is displayed on the menu screen of the Digital Interface Box.  The projector does not have 
the “RETURN” button, but same operation is available with the  button.
[Art-Net SETUP]
Make settings to use the Art-Net function.
1) Press  as to select [Art-Net SETUP].
2)  
Press 
 qw to select an item.
 fThe items will switch each time you press the button.
[OFF] Disables the Art-Net function.
[ON(2.X.X.X)] Enables the Art-Net function and sets the IP address to 2.X.X.X.
[ON(10.X.X.X)] Enables the Art-Net function and sets the IP address to 10.X.X.X.
[ON(MANUAL)] Enables the Art-Net function and uses the IP address set in [NETWORK SETUP].
 fWhen other than [OFF] is selected, proceed to Step 

3).
3) Press the  button.
 fThe  [Art-Net SETUP] screen is displayed.
4) Press  as to select an item, and press qw to switch the settings.
[NET] Enter [NET] to be used when the projector processes Art-Net.
[SUB NET] Enter [SUB NET] to be used when the projector processes Art-Net.
[UNIVERSE] Enter [UNIVERSE] to be used when the projector processes Art-Net.
[START ADDRESS] Enter [START ADDRESS] to be used when the projector processes Art-Net.
5) Press as to select [STORE], and press the  button.
6)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f If [ON(2.X.X.X)] or [ON(10.X.X.X)] is selected, IP  address is calculated and set automatically.
Network connection
The projector has a network function, and the following operations are a\
vailable from the computer using the web control.
 fSetting and adjustment of the projector
 fDisplay of the projector status
 fSending E-mail messages when there is a problem with the projector
The projector supports “Crestron ConnectedTM”, and the following application software of Crestron Electronics, Inc. can be used.
 f RoomV

iew Express
 f Fusion R

V
 f RoomV

iew Server Edition
Attention
 f When a LAN cable is directly connected to the projector , the network connection must be made indoors.
Note
 f“Crestron ConnectedTM” is a system of Crestron Electronics, Inc. that collectively manages and controls devices on multiple systems 
connected to the network using a computer.
 f For details of “Crestron ConnectedTM”, refer to the website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com
To download “RoomView Express”, go to the following website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com/getroomview
 f A

 LAN cable is required to use the network function.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 139
 rExample of a normal network connection
Computer
Projector
LAN cable (straight) LAN cable (straight) Hub
 fA web browser is required to use network function. Confirm that the web browser can be used beforehand.
Compatible browser: Internet Explorer 7.0/8.0/9.0/10.0/11.0 (Windows OS), Safari 4.0/5.0/6.0/7.0 (Mac OS)
 f Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used beforehand.
 fUse a LAN cable that is compatible with category 5 or higher

.
 fUse a LAN cable of 100

  m (328'1") or shorter.
Connecting to a twisted-pair-cable transmitter
The projector has a function that can receive Ethernet signals from a tw\
isted-pair-cable transmitter together with video and audio signals via a\
 
LAN cable. Connect a LAN cable to the  terminal of the projector. (x pages 20, 26)
 rExample of network connections via a twisted-pair-cable transmitter
Computer
Projector
LAN cable (straight) LAN cable (straight)
LAN cable (straight)
Twisted-pair-cable transmitter
Hub   
						

							Chapter 4 Settings — [NETWORK] menu
140 - ENGLISH
 fFor the LAN cable between the twisted-pair-cable transmitter and the projector , use a cable that meets the following criteria:
 gCompatible with CA

T5e or higher
 gShielded type (including connectors)
 gStraight-through
 gSingle wire
 fThe maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100

  m (328'1"). If this distance is 
exceeded, image may be disrupted or a malfunction may occur in LAN communication.
 f When laying cables between the twisted-pair-cable transmitter and the pr\
ojector

, check that cable characteristics are compatible with 
CAT5e or higher using tools such as a cable tester or cable analyzer.
When a relay connector is used, include it in the measurement.
 f Do not use a hub between the twisted-pair-cable transmitter and the proj\
ector

.
 fDo not pull cables forcefully

. In addition, do not bend or fold cables unnecessarily.
 fT

o reduce the effects of noise as much as possible, stretch out the cables between the t\
wisted-pair-cable transmitter and the projector 
without any loops.
 f Lay the cables between a twisted-pair-cable transmitter and the projecto\
r away from other cables, particularly power cables.
 fWhen laying multiple cables, run them side by side along the shortest di\
stance possible without bundling them together

.
 fAfter laying the cables, confirm that the value of [SIGNAL

 QUALITY] in the [NETWORK] menu → [DIGITAL LINK STATUS] is displayed in 
green to indicate normal quality. (x
  page   136)
 fFor twisted-pair-cable transmitters of other manufacturers of which the operation has been verified with the projector , refer to the 
Panasonic website (http://panasonic.net/avc/projector/). Note that the verification for devices of other manufacturers has been made for 
the items set by Panasonic Corporation, and not all the operations have been verified. For operation or performance problems caused by 
the devices of other manufacturers, contact the respective manufacturers\
.
Accessing from the web browser
1) Start up the web browser on the computer .
2)  
Enter the IP
  address set on the projector into the URL entry field of the web browser.
3)
 
Enter the user name and the password.
 f The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the password is panasonic (lower 
case).
4) Click OK.
 fThe [Projector status] page is displayed.