Panasonic LCD Projector Pt Rz670 Operating Instructions

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 111
Luminance (lm)When [CONSTANT MODE] is set to [OFF] When [CONSTANT MODE] is set to [AUTO] or [PC]
[MAX LIGHT 
OUTPUT LEVEL]  (%) [LIGHT OUTPUT] 
(%) Runtime (hour) [MAX LIGHT 
OUTPUT LEVEL]  (%) [LIGHT OUTPUT] 
(%) Runtime (hour)
3
  000 100.0 46.031
  000100.0 46.024
  000
2
  500 100.0 38.033
  00072.0 38.030
  000
2
  000 ―――68.0 31.036
  500
Note
 fUnder influence of characteristics of each light source, conditions of use, installation environment, etc., the runtime may be shorter than the 
estimation.
 fThe duration of use is referred to as the runtime when you use the proje\
ctor successively

. The duration of use is an estimated duration and 
is not the warranty period.
Setting [BRIGHTNESS CONTROL SETUP]
Set brightness control operation.
The [BRIGHTNESS CONTROL SETUP] setting is synchronized with the [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL]  → 
[BRIGHTNESS CONTROL SETUP]. The most recent setting is reflected in both items.
1) Press  as to select [OPERATION SETTING].
2)  
Press the  button.
  
 fThe  [OPERATION SETTING]  screen is displayed.
3) Press as to select [CONSTANT MODE].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Does not correct the brightness of the screen by the brightness sensor.
[AUTO] Corrects the brightness of the screen by the brightness sensor.
When the brightness of the light source or white balance changes, the br\
ightness of the screen is 
automatically corrected.
[PC] Synchronizes nine or more projectors through a computer using the dedicated software “Multi 
Projector Monitoring & Control Software”
*1.
*1 “Multi Projector Monitoring & Control Software” is included in the supplied CD-ROM.
 f
When [PC] is selected, proceed to Step  7).
5) Press as to select [LINK].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Performs corrections by the brightness sensor on one projector without s\
ynchronizing with other 
projectors.
The duration that the constant brightness is kept will become longer by setting the value of [LIGHT
 
OUTPUT] smaller.
[GROUP A]
[GROUP B]
[GROUP C]
[GROUP D] Synchronizes corrections on multiple projectors by the brightness sensor
.
You can set up to four groups (A to D) within the same subnet by using the network function.
You can also register and synchronize up to eight projectors in one group.
7) Press  as to select [CALIBRATION TIME].
8)  
Press the  button.
 f The projector is in the adjustment mode (where the time is blinking).
9) Press  qw to select “hour” or “minute”, and press as or the number ( - ) buttons to set a 
time.
 f Selecting “hour” allows setting of only the hour in increments of one hour , and selecting “minute” allows setting of only the minute in 
increments of one minute between 00 and 59.
 f If you do not specify the time, select [OFF] between 23 and 00 o’clock or between 59 and 00 minutes.
10) Press the  button.
 f[CALIBRATION TIME] is set.
 fBrightness and color are measured at the specified time. 

The dynamic contrast function does not operate during measurement.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
112 - ENGLISH
11) Press as to select [CALIBRATION MESSAGE].
12)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[ON] Displays the message during calibration.
[OFF] Does not display the message during calibration.
13) Press as to select [APPLY].
14)  
Press the  button.
 fIf the  button is pressed with [CONST ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to other than [OFF], the light 
source brightness and white balance at the time is recorded as the stand\
ard brightness and white balance.
 f If the  button is pressed while [LINK] is set between [GROUP  

A] and [GROUP D], the group name is displayed on the 
screens of projectors that have been set in the same group.
LINK GROUP A
15) When the confirmation screen is displayed, press  qw  to select [OK], and press the  button.
Note
 f When [CONST ANT MODE] in [BRIGHTNESS CONTROL SETUP] is set to [AUTO] or [PC], keep the shutter function disabled (shutter: 
open) for at least 30 seconds to perform the brightness sensor calibration after the [BRIGHTNESS CONTROL  SETUP] setting has been 
completed.
 f If the shutter function is enabled (shutter: closed) within approx. 8 minutes after the light source has turned on while [CONST ANT

 MODE] 
in [BRIGHTNESS CONTROL SETUP] is set to [AUTO] or [PC], brightness and color cannot be measured. Therefore, brightness may be 
corrected approx. 30 seconds after the shutter function is disabled (shutter: open).
 f When the projector operates with [CONST

ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to [AUTO] or [PC], brightness and color 
are not steady for approx. eight minutes after the light source has turned on.  Therefore, brightness and color are measured automatically 
approx. eight minutes after the light source has turned on. Based on the measured result, correction is performed so that the screen 
brightness and color will be the same as the standard brightness and col\
or that are adjusted with the brightness control.
 f When the projector operates with [CONST

ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to [AUTO] or [PC], the items of 
[OPERATING MODE] and [LIGHT OUTPUT] cannot be changed.
 f When the projector operates with [CONST

ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to [AUTO], and [LINK] set to [OFF], the 
brightness will be corrected until it reaches [MAX LIGHT OUTPUT LEVEL].
 f The variation in brightness may increase due to dust accumulating on the\
 lens, screen, or inside the projector

, depending on the installation 
environment of the projector.
 f When the variation in brightness has increased due to aging of the light\
 source, or when you replaced the light source, readjust the 
brightness control.
 fWhen the projector is used continuously for more than 24 hours, set the [CALIBRA TION 

TIME] in [BRIGHTNESS CONTROL SETUP]. If it is 
not set, correction will not be performed automatically.
 f The brightness control and dynamic contrast operate simultaneously

, but the dynamic contrast does not operate while brightness and color 
are being measured.
 f The [CALIBRA

TION TIME] setting will be reflected at the time when you enter the time.
 fThe [CALIBRA

TION MESSAGE] setting will be reflected at the time when items are switched using  qw.
[LIGHT OUTPUT]
Adjust the brightness of light source.
When settings have already been made in “Initial setting (operation setting)” (x
  page   53) for the [INITIAL SETTING] screen or the 
[PROJECTOR SETUP] menu → [OPERATION SETTING], the settings have been reflected. The [LIGHT OUTPUT] setting is synchronized 
with the [PROJECTOR SETUP] menu → [OPERATION SETTING]  → [LIGHT OUTPUT]. The most recent setting is reflected in both items.
1) Press as to select [LIGHT OUTPUT].
2)  
Press 
 qw to adjust.
Operation Adjustment
Range of adjustment
Brightness Runtime (estimate)
Press w. The screen becomes brighter. The runtime becomes shorter.
10.0
  % - 100.0   %
Press q. The screen becomes darker. The runtime becomes longer.
Note
 f
[LIGHT OUTPUT] can be adjusted individually for each setting item of [OPERATING MODE]. fIn such a case when configuring multiple screens with multiple projectors, uniformity of brightness between multiple screens can be 
obtained by adjusting [LIGHT
 OUTPUT].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 113
[BRIGHTNESS CONTROL]
The projector is equipped with a brightness sensor to measure brightness\
 and color of the light source, and corrects brightness and color of 
the projected image according to the changes in brightness and color of \
the light source.
By using this function, in such a condition that multiple screens are configured using multiple projectors, you can reduce changes in overall 
brightness and white balance of the multiple screens due to light source\
 degradation and suppress variation in brightness and white balance to 
preserve uniformity.
When settings have already been made in “Initial setting (operation setting)” (x
  page   53) for the [INITIAL SETTING] screen, or the 
[PROJECTOR SETUP] menu → [OPERATION SETTING], the settings have been reflected. The [BRIGHTNESS CONTROL SETUP] setting 
is synchronized with the [PROJECTOR SETUP] menu → [OPERATION SETTING]  → [BRIGHTNESS CONTROL SETUP]. The most recent 
setting is reflected in both items.
Setting [BRIGHTNESS CONTROL SETUP]
Set brightness control operation.
1) Press  as to select [BRIGHTNESS CONTROL].
2)  
Press the  button.
 f The  [BRIGHTNESS CONTROL] screen is displayed.
3) Press  as to select [BRIGHTNESS CONTROL SETUP].
4)  
Press the  button.
 f The  [BRIGHTNESS CONTROL SETUP] screen is displayed.
5) Press  as to select [CONSTANT MODE].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Does not correct the brightness of the screen by the brightness sensor.
[AUTO] Corrects the brightness of the screen by the brightness sensor.
When the brightness of the light source or white balance changes, the br\
ightness of the screen is 
automatically corrected.
[PC] Synchronizes nine or more projectors through a computer using the dedicated software “Multi 
Projector Monitoring & Control Software”
*1.
*1 “Multi Projector Monitoring & Control Software” is included in the supplied CD-ROM.
 f
When [PC] is selected, proceed to Step  9).
7) Press as to select [LINK].
8)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Performs corrections by the brightness sensor on one projector without s\
ynchronizing with the other 
projectors.
The duration that the constant brightness is kept will become longer by setting the value of [LIGHT
 
OUTPUT] smaller.
[GROUP A]
[GROUP B]
[GROUP C]
[GROUP D] Synchronizes corrections in multiple projectors by the brightness sensor
.
You can set up to four groups (A to D) within the same subnet by using the network function.
You can also register and synchronize up to eight projectors in one group.
9) Press  as to select [CALIBRATION TIME].
10)  
Press the  button.
 fThe projector is in the adjustment mode (where the time is blinking).
11) Press  qw to select “hour” or “minute”, and press as or the number ( - ) buttons to set a 
time.
 f Selecting “hour” allows setting of only the hour in increments of one hour , and selecting “minute” allows setting of only the minute in 
increments of one minute between 00 and 59.
 f If you do not specify the time, select [OFF] between 23 and 00 o’clock or between 59 and 00 minutes.
12) Press the  button.
 f[CALIBRATION TIME] is set.
 fBrightness and color are measured at the specified time. 

The dynamic contrast function does not operate during measurement.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
114 - ENGLISH
13) Press as to select [CALIBRATION MESSAGE].
14)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[ON] Messages are displayed during calibration.
[OFF] Messages are not displayed during calibration.
15) Press as to select [APPLY].
16)  
Press the  button.
 fIf the  button is pressed with [CONST ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to other than [OFF], the light 
source brightness and white balance at the time is recorded as the stand\
ard brightness and white balance.
 f If the  button is pressed while [LINK] is set between [GROUP  

A] and [GROUP D], the group name is displayed on the 
screens of projectors that have been set in the same group.
LINK GROUP A
Note
 fWhen [CONST ANT MODE] in [BRIGHTNESS CONTROL SETUP] is set to [AUTO] or [PC], keep the shutter function disabled (shutter: 
open) for at least 30 seconds to perform the brightness sensor calibration after the [BRIGHTNESS CONTROL  SETUP] setting has been 
completed.
 f If the shutter function is enabled (shutter: closed) within approx. 8 minutes after the light source has turned on while [CONST ANT

 MODE] 
in [BRIGHTNESS CONTROL SETUP] is set to [AUTO] or [PC], brightness and color cannot be measured. Therefore, brightness may be 
corrected approx. 30 seconds after the shutter function is disabled (shutter: open).
 f When the projector operates with [CONST

ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to [AUTO] or [PC], brightness and color 
are not steady for approx. eight minutes after the light source has turned on.  Therefore, brightness and color are measured automatically 
approx. eight minutes after the light source has turned on. Based on the measured result, correction is performed so that the screen 
brightness and color will be the same as the standard brightness and col\
or that are adjusted with the brightness control.
 f When the projector operates with [CONST

ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to [AUTO] or [PC], the items of 
[OPERATING MODE] and [LIGHT OUTPUT] cannot be changed.
 f When the projector operates with [CONST

ANT MODE] in [BRIGHTNESS CONTROL SETUP] set to [AUTO], and [LINK] set to [OFF], 
brightness will be corrected until it reaches [MAX LIGHT OUTPUT LEVEL].
 f The variation in brightness may increase due to dust accumulating on the\
 lens, screen, or inside the projector

, depending on the installation 
environment of the projector.
 f When the variation in brightness has increased due to aging of the light\
 source, or when you replaced the light source, readjust the 
brightness control.
 fWhen the projector is used continuously for more than 24 hours, set the [CALIBRA TION 

TIME] in [BRIGHTNESS CONTROL SETUP]. If it is 
not set, correction will not be performed automatically.
 f The brightness control and dynamic contrast operate simultaneously

, but the dynamic contrast does not operate while brightness and color 
are being measured.
 f The [CALIBRA

TION TIME] setting will be reflected at the time when you enter the time.
 fThe [CALIBRA

TION MESSAGE] setting will be reflected at the time when items are switched using  qw.
Displaying [BRIGHTNESS CONTROL STATUS]
Display the brightness control status.
1) Press as to select [BRIGHTNESS CONTROL].
2)  
Press the  button.
 f The  [BRIGHTNESS CONTROL] screen is displayed.
3) Press  as to select [BRIGHTNESS CONTROL STATUS].
4)  
Press the  button.
 f The  [BRIGHTNESS CONTROL STATUS] screen is displayed.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 115
[BRIGHTNESS CONTROL STATUS] screen display example
When [CONSTANT MODE] of [BRIGHTNESS CONTROL 
SETUP] is set to [OFF]
The screen shows the status that the brightness control is disabled.
1
RETURN
BRIGHTNESS CONTROL STATUS
CONSTANT MODE PROJECTOR OFFMENU
When [CONSTANT MODE] of [BRIGHTNESS CONTROL 
SETUP] is set to [AUTO] and [LINK] is set to [OFF]
The screen shows the status of the brightness control in one 
projector
5
1
6
RETURN
LINK
PROJECTOR OFF
BRIGHTNESS CONTROL STATUSMENU
When [CONSTANT MODE] of [BRIGHTNESS CONTROL 
SETUP] is set to [AUTO] and [LINK] is set from [GROUP A] to 
[GROUP D]
The screen shows the status of the brightness control of 
synchronized projectors (up to eight units), including the projector 
being controlled through the on-screen menu.
2 1
3
4
5 
7
8
1:
2:
3:
4:
5:
6:
7: 192. 168. 30.   2
192. 168. 30.   3
192. 168. 30.   4
LINK
UPDATE PROJECTOR
GROUP A
PROJECTOR2
PROJECTOR3
BRIGHTNESS CONTROL STATUS
MENU SELECT
When [CONSTANT MODE] of [BRIGHTNESS CONTROL 
SETUP] is set to [PC]
5
1
6
RETURN
CONSTANT MODE
PROJECTOR PC
BRIGHTNESS CONTROL STATUSMENU
1 Display the name of the projector
.
2  
Display the synchronized group.
3

 
Display the IP
  address of the projector.
4
 
Display the names and IP
  addresses of projectors in same group detected over the network.
5
 
Display the status by color
 .
Green: There is an allowance for brightness correction.
Yellow: There is little allowance for brightness correction.
Red: There is a brightness control error.
6
 
Display error detailed messages.
7

 
Display error messages.
When the message [Failed to apply BRIGHTNESS CONTROL

 to some projectors.] appears, it means that synchronization with the 
projector displayed in red has failed.
Press as to select the projector displayed in red, and press the  button to display the error details.
8
 
Update to the latest status information.
 r Error details
Error message Measures to take
[Exceed maximum number of 
projectors.]
 f Limit the number of projectors in one group to eight.
 fWhen synchronizing nine or more projectors, use the dedicated software “Multi Projector 
Monitoring & Control Software”*1 through a computer.
[Please check the COMMAND 
CONTROL setting.]
 f Set [NETWORK CONTROL]  →

 [COMMAND CONTROL] to [ON] for the projector in error.
 f Set [NETWORK CONTROL]  →

 [COMMAND PORT] of all projectors to be linked to the same value.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
116 - ENGLISH
Error messageMeasures to take
[Please check the USER NAME 
and PASSWORD in the COMMAND 
CONTROL setting.]
 f Assign the same [User name] and [Password] strings that have web control administrator rights to 
all projectors to be linked.
[Cannot apply BRIGHTNESS 
CONTROL. Please check projector 
status.]
 f The projector is in standby

. Switch on the power.
[Brightness Sensor Error]
 f There is a problem with the brightness sensor

. If problems persist even after switching on the 
power, consult your dealer.
*1 “Multi Projector Monitoring & Control Software” is included in the supplied CD-ROM.
Note
 f If the synchronized projectors are not displayed in the list, check the \
following: gAre there devices with the same IP
 address on the network?
 gAre the LAN cables connected correctly? ( x

  page   138)
 gAre the subnets of the projectors the same? gAre the same [LINK] settings applied to a group? fRefer to [NETWORK SETUP] ( x

  page   136) or “[Network config] page” (x
  page   147) on how to change the projector name.
Brightness control adjustment procedure example
The steps exemplify an adjustment to link the brightness of eight projectors connected in a network.
1) Connect all projectors to the hub using LAN cables. (x   page   138)
2)  
Switch on all projectors and start projection.
3)

 
Set [CONST
 ANT MODE] of [BRIGHTNESS CONTROL SETUP] to [OFF], and select [APPLY], and then 
press the  button.
4)
 
Set [OPERA
 TING MODE] of each projector to the same setting. ( x
  page   109)
5)
 
Set [SUBNET MASK] and [IP
  ADDRESS] in each projector.
 fTo be able to communicate over the network, set the same value in [SUBNET MASK] for all projectors and set a different value in [IP 
ADDRESS] for each projector.
6) Wait for at least eight minutes after projection has started until the light source brightness becomes  steady.
7)
 
Set all items in the [PICTURE] menu of all projectors to the same values\
.
8)

 
Adjust [COLOR MA
 TCHING] to match colors.
9)
 
Display the internal test pattern “All white” in all projectors.
10)

 
Set [LIGHT OUTPUT] to 100
   % or the maximum value that can be set on all projectors.
 fDepending on the [OPERA TING MODE] settings, [LIGHT OUTPUT] may not be able to be set to 100   %.
11) Set [LIGHT OUTPUT] of the projector with the least brightness to 90  % or 10   % lower than the 
maximum value that can be set.
12)
 
Adjust [LIGHT OUTPUT] of each projector
 .
 fAdjust [LIGHT  OUTPUT] of all the other projectors so that the brightness will be the same as the projector with the least brightness.
13) Set [CONST ANT MODE] of [BRIGHTNESS CONTROL SETUP] to [AUTO], and [LINK] to [GROUP A] on 
all projectors.
14)
 
Select [APPL
 Y] of [BRIGHTNESS CONTROL SETUP] and press the  button in all projectors.
 fBrightness control starts.
Note
 fBrightness is automatically corrected whenever the light source lights u\
p by switching on/of f the projector, etc. fWhen the variation in brightness has increased due to aging of the light\
 source, or when you replaced the light source, readjust the 
brightness control.
[STANDBY MODE]
Set the power consumption during the standby.
1) Press  as to select [STANDBY MODE].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 117
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL] Select this item to use the network function during standby.
[ECO] Select this item to reduce power consumption during standby.
Note
 fWhen [ECO] is set, the network function, the  terminal, and some RS - 232C commands become inoperable during standby. 
In the [NORMAL] setting, the network function and the  terminal become operable during standby.
 f When [ECO] is set, it may take approximately 10 seconds longer before the projector starts projecting after the power is turned on, 
compared with when [NORMAL] is set.
 fThe [ST

ANDBY MODE] settings are not reset to the factory defaults even when [ALL USER DATA] is executed from the [PROJECTOR 
SETUP] menu → [INITIALIZE] ( x
  page   124).
[SCHEDULE]
Set the command execution schedule for each day of the week.
Enabling/disabling the schedule function
1) Press as to select [SCHEDULE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the schedule function.
[ON] Enables the schedule function. Refer to “How to assign a program” (
x
  page   117) or “How to set a 
program” (x
  page   117) for how to set the schedule.
Note
 fWhen [SCHEDULE] is set to [ON], the [ST ANDBY MODE] setting is forcibly switched to [NORMAL], and the setting cannot be changed. 
Even if [SCHEDULE] is then set to [OFF] when in this state, the setting of [ST ANDBY MODE] remains at [NORMAL].
How to assign a program
1) Press as to select [SCHEDULE].
2)  
Press 
 qw to select [ON], and press the  button.
 fThe  [SCHEDULE] screen is displayed.
3) Select and assign program to each day of week.
 fPress  as to select the day of week, and press qw to select a program number.
 fY

ou can set the program from No.1 to No.7. “ -   -   - ” indicates that the program number has not been set.
How to set a program
Set up to 16 commands to each program.
1) Press as to select [SCHEDULE].
2)  
Press 
 qw to select [ON], and press the  button.
 fThe  [SCHEDULE] screen is displayed.
3) Press  as to select [PROGRAM EDIT].
4)  
Press 
 qw to select a program number, and press the  button.
5)
 
Press 
 as to select a command number, and press the  button.
 fYou can change the page using  qw.
6) Press asqw to select [TIME], and press the  button.
 fThe projector is in the adjustment mode (where the time is blinking).
7) Press  qw to select “hour” or “minute”, and press as or the number ( - ) buttons to set a 
time, and then press the  button.
8)
 
Press 
 asqw to select [COMMAND].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
118 - ENGLISH
9) Press the  button.
 fThe  [COMMAND] detailed screen is displayed.
10) Press  as to select a [COMMAND].
 fFor [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time you press  qw .
 fWhen [INPUT] is selected, press the  button, and then press 

asqw to select the input to be set.
[COMMAND] Detailed settings of 
[COMMAND] Description
[POWER ON] ―Switches on the projector.
[STANDBY] ―Enters standby.
[SHUTTER] [OPEN]
Disables the shutter function (shutter: open).
[CLOSE] Enables the shutter function (shutter: closed).
[INPUT] [RGB1]
Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[DVI
- D]Switches the input to DVI
- D.
[HDMI] Switches the input to HDMI.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[SDI]
*1Switches the input to SDI.
[INPUT1] - [INPUT10]
*2Switches the input to DIGITAL LINK, and switches the input of the 
Panasonic twisted-pair-cable transmitter to the specified input.
[OPERATING MODE]
*3
[NORMAL] Prioritizes luminance.
[ECO] Controls the power to increase the life of the light source with higher 
luminance.
[LONG LIFE1] Although the luminance is lower than that of [ECO], it controls the 
power to increase the life of the light source.
[LONG LIFE2] Although the luminance is lower than that of [LONG LIFE1], it 
controls the power to increase the life of the light source.
[LONG LIFE3] Although the luminance is even lower than that of [LONG LIFE2], 
it controls the power to increase the life of the light source to the 
maximum.
[USER1] Controls the power with the settings of [USER1].
[USER2] Controls the power with the settings of [USER2].
[USER3] Controls the power with the settings of [USER3].
[P IN P] [OFF]
P IN P function is not used.
[USER1] Lays out the sub-screen with the settings of [USER1].
[USER2] Lays out the sub-screen with the settings of [USER2].
[USER3] Lays out the sub-screen with the settings of [USER3].
*1 Only for PT-RZ670
*2  
When the Panasonic twisted-pair-cable transmitter (such as the optional Digital Interface Box (Model No.: ET-
 YFB100G)) is connected to the 
projector, its input name is reflected from [INPUT1] to [INPUT10] automatically. If an item where the input name is not reflected is selected, it 
is disabled.
*3
 
If you change the settings while using the projector
 , the duration until the light source luminance decreases by half may sh\
orten or the 
luminance may decrease.
11) Press the  button.
 f The command is fixed and  n  is displayed at the left of the selected command.
 fAfter the command is fixed, press the  button to close the detailed setting screen.
12) Press  asqw to select [STORE], and press the  button.
Note
 f To delete a command the has been already set, press the  button on the remote control while the screen in Step  5) is displayed, 
or select [DELETE] at the screen in Step 6) and press the  button.
 f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command 
number

.
 fThe operating time will be the local time. ( x

  page   122)
 fIf an operation is executed with the remote control or control panel of the projector or with a control command before the command set in 
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[STARTUP INPUT SELECT]
Set the input when the projector is switched on to start projection.
1) Press  as to select [STARTUP INPUT SELECT].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 119
2) Press the  button.
 fThe  [STARTUP INPUT SELECT]  screen is displayed.
3) Press asqw to select an item.
[LAST USED] Keeps the input selected last.
[RGB1] Sets the input to RGB1.
[RGB2] Sets the input to RGB2.
[DVI
- D] Sets the input to DVI
- D.
[HDMI] Sets the input to HDMI.
[DIGITAL LINK] Sets the input to DIGITAL LINK.
[SDI]
*1Sets the input to SDI.
[INPUT1] - [INPUT10]
*2Sets the input to DIGITAL LINK, and switches the input of Panasonic twisted-pair-cable transmitter to 
the specified input.
*1 Only for PT- RZ670
*2  
When the Panasonic twisted-pair-cable transmitter (such as the optional Digital Interface Box (Model No.: ET-
 YFB100G)) is connected to the 
projector, its input name is reflected from [INPUT1] to [INPUT10] automatically. If an item where the input name is not reflected is selected, it 
is disabled.
Note
 f When [BACKUP  INPUT MODE] in the [DISPLAY OPTION] menu → [BACKUP INPUT SETTING] ( x   page   94) has been set to [ON], 
and the projector has been turned off with the input set to HDMI, projection will start with the DVI - D input, even when [STARTUP INPUT 
SELECT] is set to [LAST USED].
[RS-232C]
Set the communication conditions of the / terminals. Refer to “/ terminal” 
(x   page   169).
Setting the communication condition of the  terminal
1) Press  as to select [RS-232C].
2)  
Press the  button.
 f The  [RS-232C]  screen is displayed.
3) Press  as to select [INPUT SELECT].
4)  
Press 
 qw to switch the item.
[PROJECTOR] Use the  terminal of the projector to perform RS - 232C communication.
[DIGITAL INTERFACE BOX] Performs RS
- 232C communication via the optional Digital Interface Box (Model No.: ET
-
 YFB100G) 
and the  terminal.
5) Press  as to select [(IN) BAUDRATE].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[9600]
Select the proper speed.
[19200]
[38400]
7) Press  as to select [(IN) PARITY].
8)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NONE]
Select the parity condition.
[EVEN]
[ODD]   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
120 - ENGLISH
Setting the communication condition of the  terminal
1) Press as to select [RS-232C].
2)  
Press the  button.
 f The  [RS-232C]  screen is displayed.
3) Press  as to select [(OUT) BAUDRATE].
4)  
Press 
 qw to switch the item.
[9600] Select the proper speed.
[19200]
[38400]
5) Press  as to select [(OUT) PARITY].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NONE]
Select the parity condition.
[EVEN]
[ODD]
Setting the response
1) Press  as to select [RS-232C].
2)  
Press the  button.
 f The  [RS-232C]  screen is displayed.
3) Press  as to select [RESPONSE(ID ALL)].
4)  
Press 
 qw to switch the item.
[ON] Returns the response when the ID setting is ALL.
[OFF] Does not return the response when the ID setting is ALL.
5) Press as to select [GROUP].
6)  
Press 
 qw to switch the item.
[A] - [Z] Controls multiple projectors simultaneously by sending the ID of RS - 232C. You can set groups from 
[A] to [Z]. The projector responds when the ID of RS - 232C matches the setting.
7) Press as to select [RESPONSE(ID GROUP)].
8)  
Press 
 qw to switch the item.
[ON] Returns the response when the ID setting is GROUP.
[OFF] Does not return the response when the ID setting is GROUP.
Note
 fWhen [INPUT  SELECT] is set to [DIGITAL INTERFACE BOX], communication using that serial terminal is available only when the 
corresponding device (such as the optional Digital Interface Box (Model No.: ET- YFB100G)) is connected to the  
terminal.
 f When transferring logos via the optional Digital Interface Box (Model No.: ET-

YFB100G), “NO SIGNAL SLEEP” of ET
-
 YFB100G must be set 
to “OFF” to avoid interruption of communication.
 f When [INPUT

 SELECT] is set to [DIGITAL INTERFACE BOX], communication speed is fixed to 9   600   bps.
[STATUS]
Display the status of the projector.
1) Press as to select [STATUS].