Panasonic Kx-Tvp150 Voice Processing System Guide

12 l How To Use This Manual _ 
This manual consists of nine chapters as follows: 
- Chapter 1 Introduction - explains the features of the 
Voice Processing System (VPS) and construction of this 
manual. 
- Chapter 2 System Configuration and Installation - 
explains the configuration in hardware/software of the 
VPS and how to install (locate and correct) the VPS. 
- Chapter 3 System Administrator’s Guide - explains the 
initial settings of the VPS system as the job of the System 
Administrator. 
-...

12 0 
How To Use This Manual - 
Telephone Key Operation 
Telephone key 
cl * 
OK? 
cl 
0 
TUV 
cl 8 
Functions 
Exit the current menu in the voice prompt (back up) 
Call the operator for Non-Subscriber 
Help guidance for Subscriber 
Change the voice level when listening to a message 
Control playback speed when listening to a message 
Various functions assigned depending on the program 
Dial by name 
Bulletin Board Service 
Department Dialing 
Login 
Voice Mail Service 
Restart (Subscriber’s main...

‘ 
::: 
., 
:J 
12 l How To Use This Manual 
_ 
Data Terminal Keyboard Operation 
@VT220 Compatible Terminal 
Key 
T 
-1 
+ 
PI rI [91 
[RETURN] 
[\I 
Functions 
Move reversed line up 
Move reversed line down 
Move reversed item to the right 
Move reversed item to the left 
Directly move reversed line or item to the specified number 
Select reversed item 
Exit and return to the previous step in the menu 
l Other RS-232C Terminal (ASCII Terminal) 
. 
I Key 
[I] - [9], then [RETURN] 
I\1 
! Functions 
I...

Chapter 2 
System Configuration and 
Installation 
This chapter tells you about the configuration of the VPS 
system, expansion of the system, and how to install the VPS. 
Contents 
2.1 What is a System Configuration? ..................... M-2-2 
2.1.1 CO Card ................................................. M-2-5 
2.1.2 DSP Card ............................................... M-2-5 
2.1.3 Hard Disk Drive .................................... M-2-5 
2.1.4 CPU Card...

21 a What is a System Configuration?- 
The Voice Processing System (VPS) comprises a CO card, 
a DSP card, the CPU card, a hard disk drive and propri- 
etary system software. The VPS can be expanded to be able 
to handle up to eight simultaneous calls and store up to 
10.5 hours of voice data by installing expansion units such 
as additional CO cards, DSP cards, and a hard disk drive. 
Overview of the Voice Processing System Unit 
Reset Button + 
To EIA 
(RS-232C -+ 
Interface) 
To Telephone + 
Line...

hat is a System Configuration?. 
Inside View of the Voice Processing System 
Reset 
Button 
Metal 
Board 
EIA 
Connet 
(RS-23 
/’ 
ctor 
12C) 
-1 
I 71 r / / I I / I l/ I I Ii- 
/ 
CPU Card Alarm 
Indicator 
. Running 
Indicator 
L Power 
Indicator 
 
Power 
Switch 
Hard Disk 
,---- Drive 
DC Jack for 
Optional 
- Battery 
Adaptor 
AC Power 
Jack 
Manager’s Guide Configuration & Installation M-2-3  

‘- 
;,: 
,p; 
_,- 
: -_ 
’ 
21 a What is a System Configuration? 
The Name of Parts 
Back-up Battery 
Reset Button 
Metal Board Note: 
EIA Connector 
(RS-232C) During power failure, clock and parameter setting memory 
is protected from loss by the back-up batteries included. 
Pressing the Reset Button reboots the system beginning 
with the self test. However, set patameters and data are not 
deleted. 
To protect the printed circuit board from static electricity, 
first discharge any body static by...

21 l What is a System Configuration?- 
2.1.1 CO Card 
2.1.2 DSP Card 
2.1.3 Hard Disk Drive 
2.1.4 CPU Card 
:.::’ 
, 
.A 
.., .- 
: : 
Manager’s Guide Configuration & Installation M-2-5  The telephone line interface (CO card) transmits and 
receives analogue signals to and from the telephone line. 
The analog input signal is digitized at a sampling rate of 8 
kHz to create an 8-bit digital signal. 
The CODEC facility is on the DSP card and consists of 
two digital signal processors (DSP) and voice...

‘. 
21 l What is a System Configuration? 
Note 1: 
Note 2: 
switch positions, and it is normally left in the 0 setting. 
When set to position 1, the RS-232C parameters are initial- 
ized when the system is booted up (see Note 1). This set- 
ting should be used if there is some uncertainty about the 
parameters to be used when making connections. When the 
switch is set to position 5, the system parameters are ini- 
tialized and set automatically to the factory default values 
(see 3.48) when the system...

21 0 
What is a System Configuration?- 
Increasing the Number of 
CO Cards (Phone Lines) 
: 
., 
Increasing the Number of 
DSP Cards 
Increasing the Number of 
Hard Disk Drives 
Other Options: 
Modem Card 
: .’ Battery Adaptor 
By installing up to four CO cards in free slots, the number 
of lines the VPS can handle may be increased to eight. One 
of the four incoming call services (Voice Mail, Automated 
Attendant, Bulletin Board or Interview Service) can be 
assigned to each line. In addition, each line...