Panasonic Kx-Tvp150 Voice Processing System Guide

2.2.3 Connecting a Data Terminal or a 
Printer to the VPS 
Printer Connection 
1 
Make cables so that the printer may be connected to the 
KX-TVP150 as shown in the chart. Cables must be 
shielded and the maximum length is 6.5 feet. 
Connection Chart: 
KX-TVP150 RS-232C 
Printer RS-232C 
Pin Signal Circuit 
No. Name 
Type 
@IA) 
1 FG AA 
3 RXD BB 
2 TXD BA 
1 
20 DTR CD 
7 SG Al3 
5 CTS CB 
6 DSR cc 
8 DCD CF 
‘ 
Circuit  Circuit 
Type  Type 
WV  WV Signal  Signal 
Name  Name Pin  Pin 
No.  No. 
AA 
BA...

2.2.3 Connecting a Data Terminal or a 
Printer to the VPS 
The pin configuration of the EIA (RS-232C) connector is 
as follows. 
Pin 
Number Signal Name 
1 FG Frame Ground Transmit- AA 101 
2 TXD ted Data BA 103 
3 
RXD Received Data Request To BB 104 
4 RTS Send CA 105 
5 
6 
I I CTS cE;r~ To Send Data Set 1 C$ / 
DSR Readv :irl 
7 SC Signal Ground Data Car- AB 102 
8 DCD rier Detect CF 109 
20 DTR Data Terminal Ready CD 108.2 
EIA (RS-232C) 
SIGNALS: 
Frame Ground (FG) 
Connects to the unit frame and...

2.2.3 Connecting a Data Terminal or a 
Printer to the VPS 
, 
Communication 
parameter 
Data Termial Ready (DTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (output) 
This signal line is turned ON by the unit to indicate that it 
is ON LINE. Circuit DTR ON does not indicate that com- 
munication has been established with the printer. It is 
switched OFF when the unit is OFF LINE. 
Data Carrier Detect (DCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

: 
.: 
2.2.4 
Connecting the Power Cable to the 
VPS 
Data Terminal 1 
RS-232C 
Before connecting the power cable to an AC outlet, make 
sure all other connections (RS-232C data terminal with 
VPS, PBX with VPS, PBX with telephone lines) are secure. 
Use the AC outlet dedicated to the VPS unit. 
Interface 
II Panasonic 
ELECTEXMIC 
- SWITCH1116 SfSTEn 
PBX -To AC Outlet 
Operator 
(Message 
Manager) 
1  EXT. 23 
EXT. 24 
EXT. 25 
Manager ‘s Guide Configuration & Installation M-2-2 1  

2.2.5 Starting the System 
Once all the connections are firmly connected, the System 
Administrator may start the VPS system. Before starting, 
turn the power switch to ON, the system will start up in the 
following sequence. 
Note: The calls to the VPS can be processed after the Running 
Indicator (LED) lights. 
1 Turn the power switch of the VPS to ON. 
The Power Indicator will go on. The green running indica- 
tor will light once, then turn off. 
2 “SYSTEM TEST” will be displayed on the screen of the...

2.2.5 Starting the System 
Note: If there is any hardware failure on the CO card or the DSP 
card, the system will identify the defective boards. If there 
is no normal pair of ports and DSP, the system cannot 
provide any service to the caller. Refer to chapter 7 which 
is the Troubleshooting Guide in this manual. 
To enter system administration, the System Administrator 
must press the [RETURN] key and enter his password. 
ENTER THE ADMINISTRATOR 
PASS WORD := 
Note: There is no factory setting for the...

:: :: 
. . ../ 
.:I 
‘., ‘....’ 
Chapter 3 
System Administrator’s Guide 
This chapter explains what a System Administrator is and 
provides step-by-step instructions for such system setup tasks 
as setting up mailboxes, setting system parameters and 
checking system status. 
Contents 
3.1 What is a System Administrator? .................. M-3-2 
3.2 Initializing the System ................................... M-3-3 
3.3 Setting the System Parameters .................... M-3-6 
3.3.1 Hardware Settings...

31 l What is a System Administrator? 
The System Administrator of the VPS initially takes care 
of the operational characteristics of the entire system. You 
can set up system parameters, administrate the parameters, 
or diagnose the system using the interactive screen-based 
program. 
What you will do: 
- Initialize the System (See 3.2) 
- 
Set the System Parameters (See 3.3) 
, 
M-3-2 System Administrator Manager’s Guide  

32 l Initializing the System 
Before actually using the VPS, the System Administrator 
must initialize the system to clear it of all messages, clear 
all mailboxes, and initialize the system tables on the hard 
disk drive. 
Before starting the system 
initialization: 
To initialize the system: 
1 
2 
3 
4 
Specify the RS-232C terminal type:  Use the work sheets provided to record the information 
you will need to initialize the system. Just fill in the blanks 
with the information requested. Once you...

32 0 
Initializing the System 
A menu will appear: 
1 : Program 
2 : System Reports 
3 : Utility Command 
4 : System Reset/Clear 
6 
ENTER THE NUMBER:= 
Press [4] for System Initialization. 
A prompt will appear: 
.  May I delete all messages and mailboxes? (Y/N) 
7 Press [Y] (this moves you to the off-line mode). 
A prompt will appear: 
System Reset/Clear Menu 
1. Mailbox No. Length [3] 
2. First Digit of Extension [1,2,3,4,5,6,7,8] 
3. System Manager’s Mailbox No. [999] 
4. Message Manager’s Mailbox...