Panasonic Kx-Tvp150 Voice Processing System Guide

21 0 
What is a System Configuration? 
Installing options for 
expansion: 
Metal 
Board 
Slot for 
2nd CO 
Card 
Slot for 
3rd CO 
Card 
Slot for 
4th CO 
Card 
EIA Port 
(RS-232C \. 
.I 
I’ 
/’ 
Note: The optional cards for system expansion should be inserted 
into each ones proper slot. 
To protect the printed circuit board from static electricity, 
first discharge any body static by touching the metal 
board. 
Refer to the manual accompanying the optional card 
about precautions and the installation...

22 l How to Install the VPS 
- 
(Hardware) 
- 
(Software) 
Before using the VPS system, the system Administrator 
should perform the following settings: 
Install the VPS on the floor or on the wall (See 2.2.1) 
Connect telephone lines between the VPS and PBX 
(See 2.2.2) 
Connect a data terminal to the VPS (See 2.2.3) 
Connect the power cable to the VPS (See 2.2.4) 
Start the system (See 2.2.5) 
Initialize the system (See 3.2) 
Set the RS-232C parameters (See 3.3.1.1) 
Generate the clock (See 3.2) 
Set...

‘ 
1::’ : 
:. 
2.2.1 Where can the VPS be installed? 
Installation Precautions 
1 
2 
3 
4 
5 
6 
7 
8 
Wiring Precautions 
1 
2 
3 
The VPS can be installed on the floor or on the wall. Please 
read the following notes concerning installations and con- 
nections before installing the VPS system. 
Avoid installing the VPS system in the following places: 
(Doing so may result in malfunction, noise or discolora- 
tion .) 
In direct sunlight and hot, cold, or humid places. 
New areas where there are thermal...

2.2.1 Where can the VPS be installed?- 
Mounting the VPS on the Wall 
.’ 
: 
/ 
! 
To Mount on a Wooden 
Wall: 
The wall where the VPS is to be mounted must be able to 
support the weight of the VPS. If screws other than the 
ones supplied are used, use the same-sized diameter screws 
as the enclosed ones, 
‘ 
1 Place the templet (included) on the wall to mark the 3 
. 
screw positions. 
Templet 
t- 
I -----I-K J 
2 Install the 3 screws into the wall. 
Drive the screw to 
this position. 
3 Hook the unit...

, 
2.2.1 Where can the VPS be installed?- 
To Mount on Concrete or 
Mortar Walls: 
1 
2 Place the templet (included) on the wall to mark the 3 
screw positions. 
Drill 3 holes and drive the anchor plugs (included) with a 
hammer, flush to to the wall. 
3 
4 
To the wall surface 
~ncf~

2.2.2 Connecting Telephone Lines to the 
VPS 
To connect telephone 
lines: 
The VPS system must be connected to the telephone line 
before starting the system. Up to eight telephone lines can 
be connected to the VPS. Each telephone line is inserted 
into the modular jack on the CO card assigned to one of 
the following incoming call services: Voice Mail Service, 
Automated Attendant Service, and Bulletin Board Service. 
‘ 
1 Unscrew four screws on both the right and left sides of the 
VPS unit, then...

2.2.2 
Connecting Telephone Lines to the 
VPS 
2 Insert the modular plug of the telephone line into the mod- 
ular jack on the CO card. 
Slot for 
CO Card 2 ’ 
Note: 
CO Card 1 ’ 
. 
Telephone Line Slot for 
Slot for 
Modular Jacks 
CO Card 3 CO Card 4 
Make sure the telephone line is connected to the proper 
modular jack. Modular jacks on the CO card correspond 
to the port numbers as follows: 
You can assign one of the incoming call services according 
to the port number. 
M-2-14 
Configuration &...

2.2.2 Connecting Telephone Lines to the 
VPS 
3 Connect the telephone line to the extension port of the 
PBX. 
Note: 
1 
Panasonic 
Your PBX 
KX-TVPI 50 
Follow the instructions on the PBX to connect the tele- 
phone line to the extension port. 
Use a 2 conductor wiring cord. The maximum length of 
the wire varies according to your PBX type. Please refer to 
your PBX Installation Manual. Remember the connected 
extension port number on the PBX. You will call it when 
accessing one of the assigned...

, 
.: 
: : 
2.2.2 
Connecting Telephone Lines to the 
VPS 
4 Place the front cover to the VPS system (and PBX if the 
cover is removed). 
Reverse the procedure of step 1. 
5 Tighten the four screws firmly. 
Reverse the procedure of step 1. 
‘ 
M-2-16 Configuration & Installation Manager’s Guide  

2.2.3 Connecting a Data Terminal or a 
Printer to the VPS 
RS-232C parameters 
Connecting RS-232C 
cable 
Note: For the system administration (system set-up, mailbox set- 
up, and system diagnosis), the RS-232C terminal must be 
connected to a serial interface (EIA port) of the unit. If the 
DEC VT220 (100) or VT220 (100) compatible terminal is 
used, the System Administrator can set up system param- 
eters and diagnose the system with the conversational 
menu-driven program. Other RS-232C terminals can...