Panasonic Kx Tg9541 Operating Instructions Manual

your service provider/telephone company to
deactivate your voice mail service.
If your service provider/telephone company
cannot do this:
– Set this unit’s “Ring count ” setting so that
this unit’s answering system answers calls
before the voice mail service of your service
provider/telephone company does. It is
necessary to check the number of rings
required to activate the voice mail service
provided by your service provider/telephone
company before changing this setting.
– Change the number of rings...

Voice mail service forlandline
Voice mail is an automatic answering service
offered by your service provider/telephone
company. After you subscribe to this service, your
service provider/telephone company’s voice mail
system answers calls for you when you are
unavailable to answer the phone or when your line
is busy. Messages are recorded by your service
provider/telephone company, not your telephone.
Please contact your service provider/telephone
company for details of this service.
Important:
R To use...

C Connect the AC adaptor cord and
telephone line cord.
3 Insert the lower tabs of the adaptor into the
unit’s bottom slots ( A), then insert by pushing
down the levers of the adaptor into the upper
slots ( B).
R The words “UP WALL” should be facing up.
4 Mount the unit on a wall then slide down to
secure in place.
Charger
Drive the screws (not supplied) into the wall.
For assistance, please visit http://www.panasonic.com/help63
Useful Information

TG954x(en)_0528_ver011.pdf   632013/05/28   11:09:553
21...

Error messages
Display messageCause/solution
Base no power
or
No link. Re-connect
base AC adaptor.RThe handset has lost communication with the base unit. Move
closer to the base unit and try again.
R Unplug the base unit’s AC adaptor to reset the unit. Reconnect
the adaptor and try again.
R The handset’s registration may have been canceled. Re-register
the handset (page 46).
BusyRNo cellular phone is paired to the base unit. Pair a cellular phone
(page 18).
R The called unit is in use.
R Other units are...

TroubleshootingIf you still have difficulties after following the instructions in this section, disconnect the base unit’s AC
adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset, and then
insert the batteries into the handset again.
General use
ProblemCause/solution
The handset does not turn on
even after installing charged
batteries.R Place the handset on the base unit or charger to turn on the
handset.
The unit does not work.RMake sure the batteries are installed...

Menu list
ProblemCause/solution
The display is in a language I
cannot read.RChange the display language (page 16).
I cannot register a handset to a
base unit.RThe maximum number of handsets (6) is already registered to
the base unit. Cancel unused handset registrations from the
base unit (page 46).
Battery recharge
ProblemCause/solution
The handset beeps and/or flashes.RBattery charge is low. Fully charge the batteries (page 11).
I fully charged the batteries, but
– still flashes,
– is displayed, or
–...

ProblemCause/solution
I cannot make or answer cellular
calls with the handset or base
unit.RDepending on the cellular phone’s compatibility, you may not be
able to make or answer cellular calls even if the cellular phone
is connected to the base unit.
R Make sure that the CELL indicator lights up and the cellular
phone is connected to the base unit (page 20).
R If someone is talking on a cellular call or using the headset, you
cannot use the cellular feature. There can be only one active
Bluetooth...

ProblemCause/solution
Caller information is not
announced.RThe ringer volume for landline is turned off. Adjust the ringer
volume (page 40).
R The ringer volume for cellular line is turned off. Adjust the ringer
volume (page 39).
R When one handset is selected to ring for cellular calls, other
units do not announce caller information. To change the
selection, see page 19.
R The Talking Caller ID feature is turned off. Turn it on (page 41).
R The ring as cell mode is set to  “On (without Talking
CID) ”....

ProblemCause/solution
Noise is heard during a call on
the headset.RA Bluetooth headset can communicate with the base unit within
a range of approximately 10 m (33 feet). The connection may
be subject to interference from obstructions such as walls or
electronic devices. Move closer to the base unit.
I cannot connect my headset to
the base unit.RConfirm that your headset is turned on.
R If your headset is already connected to another Bluetooth
device such as your cellular phone, disconnect the headset...

Answering system
ProblemCause/solution
The unit does not record new
messages.RThe answering system is turned off. Turn it on (page 54).
R The answering system does not answer or record calls from
cellular lines.
R The message memory is full. Erase unnecessary messages
(page 56).
R The greeting setting is set to  “Greeting only ” or
Greeting1&Only . Change the setting (page 54).
R If you subscribe to a voice mail service, messages are recorded
by your service provider/telephone company, not your...