Panasonic Kx Tg2730 Operating Instructions Manual

C
Bottom of the unit with the 
adaptor locked into position
81
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
C
Arrow C
6
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antennas.
7
To charge the handset battery:
Place the handset on the base unit.
•The CHARGE indicator lights.
5
While keeping the adaptor held
to the base unit, slide the wall 
mounting adaptor to 
the left until it clicks 
into place.
4
Adjust the adaptor to hold the
base unit, aligning...

82
Wall Mounting
To remove the wall mounting adaptor
Push up the RELEASE LEVER (#) with your thumb and slide the adaptor
to the right ($) with the tab kept up to release the lock. Remove the
adaptor.
RELEASE LEVER
$
#
RELEASE
LEVER
Bottom of the unit with the 
adaptor released
Adding Another Phone
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard...

83
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
A nickel cadmium battery that is recyclable powers the
product you have purchased. At the end of its useful life,
under various state and local laws, it is illegal to dispose of
this battery into your municipal waste stream. Please call 
1-800-8-BATTERY for information on how to recycle this
battery.
Battery will need to be replaced, even if you cleaned the charge contacts
and charged the battery fully, but after...

84
Canceling Registration/Re-registration
Canceling the Handset Registration
If you no longer need to use the handset or if you need to register the
handset to a different base unit of the same model, it may be necessary to
cancel the registration.
Only one handset can be canceled at a time near the base unit.
Make sure the handset and the base unit are not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ, and press á.
3
Scroll to “Registration” by pressing Ö
or Ñ, and...

85
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Re-registering the Handset
If you want to re-register the handset to the base unit or a different base unit
of the same model, you need to register it to that base unit. The handset will
be given a new extension number of that base unit. Only one handset can be
registered at a time. Make sure the base unit and the other handsets are
not being used. Registration must be completed within 1 minute.
1
Handset:Press (CONF/FUNCTION). 
2...

86
If the Following Appear...
If the unit detects a problem, one of the following messages will be
displayed on the handset. Error beeps or a busy tone will sound.
Display messageCause & Remedy
The battery needs to be charged. Recharge the
battery (p. 13).
The battery has been discharged. The handset
will not work. Charge the battery fully (p. 13).
The handset has lost communication with the
base unit. Walk closer to the base unit, and try
again.
• The called handset/base unit is in use.
• The handset...

87
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Display messageCause & Remedy
• If the radio communication between the
handset and the base unit is partially impaired,
this display will be shown.
• If more than one unit is in use, such as
conducting an external/internal call or listening
to messages, you may not be able to use
another unit. Try again later.
• If 2 other users are listening to messages, or
another user is listening to messages while the
Answering System is...

88
Display messageCause & Remedy
When you tried to call another handset in the 
2-Way Radio mode;
– the handset is too far from your handset. Walk
closer to the handset.
– 
2-Way Radio mode on the handset is off (p. 58).
– The called handset is talking with another
handset in the 2-Way Radio mode.
The handset you tried to make a call has not been
registered to the base unit. Register it (p. 26, 85).
• 8 handsets have already been registered to the
base unit. To cancel another handset
registration, see...

89
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Troubleshooting
Problem
“No link to base.
Walk closer to 
base and try 
again.” is displayed and
an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The handset and/or the
base unit does not ring.
The handset display is
blank.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the handset
starts to ring and stops the
program/search.
You cannot make...

90
Troubleshooting
Problem
You cannot make a call
even if the line is free.
The unit does not display
the caller’s name and/or
phone number.
The handset display exits
the Caller List.
You cannot page the
handset or base unit.
You cannot redial by
pressing
(PAUSE/REDIAL)
on the handset or
(REDIAL/PAUSE)on the
base unit
.
You cannot have a
conversation or listening to
messages using the
headset.
Cause & Remedy
•If more than one other user is using the
handsets and base unit, you may not be able
to make a...