Panasonic Kx Tg2730 Operating Instructions Manual

Installation
11
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Connections
•USE ONLY WITH Panasonic AC ADAPTOR PQLV10 (Order No. PQLV10Z).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•To connect a standard telephone on the same line, see page 82.
•If your unit is connected to a PBX which does not support Caller ID services, you
cannot access those services.
Hook
Telephone Line CordAC AdaptorPower Outlet (AC 120 V, 60 Hz)...

Installation
12Battery strength
You can check the battery strength on the handset display.
The battery strength is as shown in the chart below.
Display promptBattery strength
Fully charged
Medium
Low
Needs to be recharged.
Discharged
Battery Charge
Place the handset on the base unit and charge for
about 15 hoursbefore initial use.
•The CHARGE indicator lights, a beep sounds and
“Charging” will be displayed. 
Installing the Battery in the Handset
Insert the battery into the handset as shown, matching the...

13
Preparation
For assistance, please call: 1-800-211-PANA(7262) •The battery operating time may be shortened depending on usage conditions and
ambient temperature.
•Clean the handset and the base unit charge contacts with a soft, dry cloth
once a month. Clean more often if the unit is subject to grease, dust or high
humidity.Otherwise the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the base
unit until “Recharge battery” is displayed and/or...

Programmable Settings
14
Programming Guidelines
This unit has programmable functions. Most of them are selected from the
function menu on the display (p. 15).
How to select a function item from the menu
Make sure the handset is not being used.
1. Press 
(CONF/FUNCTION). 
•The main menu is displayed (p. 15).
2. You can scroll through the menu by pressing
Öor Ñ. Scroll to the desired item by
pressing 
Öor Ñ.
3. Press 
áto select the item.
4. If the item has a sub-menu I, it will be 
displayed. Select the...

15
Preparation
For assistance, please call: 1-800-211-PANA(7262)
•You can exit the programming mode any time by pressing (OFF).
•If you do not press any buttons for 60 seconds, the handset will exit the
programming mode.
•If the unit detects a problem, an error message will be displayed (p. 86).
Function Menu Table
You can use the following functions to customize your unit. After pressing
(CONF/FUNCTION), the main menu is displayed. Most items in the main
menu have a sub-menu I. The sub-menu Iis shown...

Programmable Settings
16
Dialing Mode
If you have touch tone service, set to “Tone”. If rotary or pulse service is
used, set to “Pulse”. Your phone comes from the factory set to “Tone”.
Make sure the base unit and the handset are not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ.
3
Press á.
4
Scroll to “Set tel line” by pressing Ö
or Ñ.
5
Press á.
6
Press áat “Set dial mode”.
•The current setting is displayed.
7
Select “Pulse” or “Tone” by pressing Öor
Ñ.
8
Press...

17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Line Mode
If the line is connected to a low voltage system such as a PBX, set to “B”.
Your phone comes from the factory set to “A”. 
Make sure the base unit and the handset are not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ,and press á.
3
Scroll to “Set tel line” by pressing Ö
or Ñ.
4
Pressá.
5
Scroll to “Set line mode” by pressing Ö
or Ñ.
6
Press á.
•The current setting is displayed.
7
Select “B”...

Programmable Settings
18
Auto Talk Feature
The Auto Talk feature allows you to answer a call by lifting the handset off
the base unit without pressing  or  . If you purchase an additional
handset (p. 26), you can answer a call by lifting it off the charger. If you
want to use this feature, turn the feature ON by programming. Your phone
comes from the factory set to OFF.
Make sure the handset is not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ.
3
Press á.
4
Scroll...

19
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Ringer Volume
Handset
You can program the handset ringer volume to HIGH, MEDIUM, LOW or
OFF. If set to OFF, the handset will not ring for external calls, and for
internal calls it will ring at the LOW level. Your phone comes from the
factory set to HIGH.
Make sure the handset is not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Ringer setting” by
pressing 
Öor Ñ, and press á.
3
Press áat “Ringer volume”.
4
Select the desired volume by...

Programmable Settings
20
Base unit
You can set the base unit ringer volume to HIGH, MEDIUM, LOW or OFF. If
set to OFF, the base unit will not ring for external calls, and for internal calls
it will ring at the LOW level. Your phone comes from the factory set to
HIGH. Make sure the base unit is not being used.
To select HIGH (preset), MEDIUM or LOW, press (RINGER/AUTO).
•Each time you press the button, the ringer volume will change and ring.
To turn the ringer OFF, press and hold (RINGER/AUTO)until 2...