Panasonic Kx Tg2700 Operating Instructions Manual
Have a look at the manual Panasonic Kx Tg2700 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
61 Advanced Operation For assistance, please call: 1-800-211-PANA(7262) Incoming Call Tone During an intercom call or while using the Room Monitor feature (p. 51), you can be informed by two tones if a call arrives. If you set to ON, this incoming call tone will be heard for as long as the line rings. To delete the incoming call tone, set to OFF. To set the incoming call tone to sound twice, set to “2”. Both the handset and base unit are preset to “2”. Handset incoming call tone Make sure the handset is not being used. 1 Press (CONF/FUNCTION). 2 Scroll to “Ringer setting”by pressing Öor Ñ, and press á. 3 Scroll to “Incoming call”by pressingÖ or Ñ, and press á. •The current setting will be displayed. 4 Select the desired setting, “On”, “Off” or “2”, by pressing Öor Ñ. 5 Press the right soft key ( ). •A beep sounds. •To exit the programming mode, press (OFF). Base unit incoming call tone Use the handset. Make sure the base unit and the handset are not being used. 1 Press (CONF/FUNCTION), and scroll to “Initial setting” by pressing Öor Ñ, and press á. 2 Scroll to “Set base unit”by pressingÖ or Ñ, and press á. 3 Press áat “Incoming call”. •The current setting will be displayed. 4 Select the desired setting, “On”, “Off” or “2”, by pressing Öor Ñ. 5 Press the right soft key ( ). •A beep sounds. •To exit the programming mode, press (OFF). SAVE SAVE Save directory HRinger setting Copy directory Ringer tone HIncoming call --------------- Incoming call Incomin tone :2GFSAVE Voice mail HSet base unit Registration --------------- HIncoming call Room monitor Incoming call Incomin tone :2GFSAVE
Wall Mounting This unit can be mounted on a wall phone plate. 1 Connect the AC adaptor. 2 Tuck the telephone line cord inside the wall mounting adaptor (#). Connect the telephone line cord ($). Fasten the telephone line cord to prevent it from being disconnected (%). To Power Outlet 3 Insert Aand Bhooks on the wall mounting adaptor into the holes on the base unit. Hooks $ #%% Bottom of the unit C AB AB C 62
63 Useful Information For assistance, please call: 1-800-211-PANA(7262) 6 Connect the telephone line cord. Mount the unit, then slide down. •Raise the antennas. 7 To charge the handset battery: Place the handset on the base unit. •The CHARGE indicator lights. 5 While keeping the adaptor held to the base unit, slide the wall mounting adaptor to the left until it clicks into place. 4 Adjust the adaptor to hold the base unit, aligning the arrow Con the base unit with the adaptor. C Arrow C C Bottom of the unit with the adaptor locked into position
To remove the wall mounting adaptor Push up the RELEASE LEVER with your thumb (#) and slide the adaptor to the right ($) with the tab kept up to release the lock. Remove the adaptor. Standard Telephone Single-Line Telephone Jack T-Adaptor (KX-J66)Telephone Line Cord Adding Another Phone This unit will not function during a power failure. To connect a standard telephone on the same line, use the Panasonic T-adaptor KX-J66. To order, call the accessories telephone number on page 2. 64 Wall Mounting RELEASE LEVER $ # RELEASE LEVER Bottom of the unit with the adaptor released
65 Useful Information For assistance, please call: 1-800-211-PANA(7262) Optional Headset H Plugging the optional headset into the handset allows a hands-free phone conversation. Please use only the Panasonic KX-TCA88 headset. To order, call the accessories telephone number on page 2. Connecting the optional headset to the handset Open the headset jack cover, and connect the optional headset to the headset jack as shown below. To switch to the speakerphone while using the headset: Press . To return to the headset, press . Belt Clip You can hang the handset on your belt or pocket using the belt clip. To attach the belt clip To remove the belt clip While pressing the top of the clip ( A), pull the right edge in the direction of the arrow ( B). Headset Jack A B
66 Battery Replacement A nickel cadmium battery that is recyclable powers the product you have purchased. At the end of its useful life, under various state and local laws, it is illegal to dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle this battery. Battery will need to be replaced, even if you cleaned the charge contacts and charged the battery fully, but after a few telephone calls, “Recharge battery” is displayed and/or “ ” continues to flash, or “Charge for 15HRS” and “ ” are displayed. Please order a new Panasonic PQPP511SVC (P-P511) battery at the telephone number shown on page 2. 1 Press the notch on the handset cover firmly and slide it as indicated by the arrow. 2 Remove the old battery. Insert the new battery into the handset as shown, matching the correct polarity (#). Press the battery down until it places into the compartment ($). 3 Close the cover. Make sure you charge the new battery for about 15 hours in order to display the battery strength prompt correctly (p. 12). 1 2
67 Useful Information For assistance, please call: 1-800-211-PANA(7262) Canceling Registration/Re -registration Canceling the Handset Registration If you no longer need to use the handset or if you need to register the handset to a different base unit of the same model, it may be necessary to cancel the registration. Only one handset can be canceled at a time near the base unit. Make sure the base unit and the handsets are not being used. 1 Press (CONF/FUNCTION). 2 Scroll to “Initial setting” by pressing Öor Ñ, and press á. 3 Scroll to “Registration” by pressing Ö or Ñ, and press á. 4 Scroll to “Deregistration” by pressing Öor Ñ. 5 Press á. 6 Press (3)(3)(5)(DEL.) to delete the registration memory. •If you make a mistake, press (HOLD/CLEAR), and enter “335”. 7 Press the right soft key ( ). •A beep sounds and the registration memory will be erased on both the handset and the base unit. •If 3 beeps sound, you entered a wrong code. The display will return to step 6. Enter “335”. •To register the handset to another base unit of the same model, start from step 5 on page 68 or see page 21. • “[-]”is shown on the top right of the display. •You can exit the programming mode any time by pressing (OFF) . •The handset will not work. To use it again, registration will be required (p. 21, 68). OKSPPRIVACY[ -] Handset [2] DeDeregistered Ex. Extension number 2 HS registration HDeregistration --------------- Set base unit HRegistration --------------- Deregistration Enter code:335 :--- Deregistration Enter code:335 Enter codeee:335 OK SPPRIVACY[ -] Press MUTE on base unit, then OK on handset to register handset OK Copy directory HInitial setting 2Way radio mode
68 Re-registering the Handset If you want to re-register the handset to the base unit or a different base unit of the same model, you need to register it to that base unit. The handset will be given a new extension number of that base unit. Only one handset can be registered at a time. Make sure the base unit and the other handsets are not being used. Registration must be completed within 1 minute. 1 Handset:Press (CONF/FUNCTION). 2 Scroll to “Initial setting” by pressing Öor Ñ, and press á. 3 Scroll to “Registration” by pressing Ö or Ñ, and press á. 4 Press áat “HS registration”. 5 Base unit: Press (MUTE). •The MUTE indicator light flashes. 6 Handset: #Press the right soft key ( ). $Wait until a long beep sounds and the display shows the registered number. The registration will be then complete. •The registered number “[1]”to “[8]” is shown on the top right of the display. •You can stop registration by pressing (OFF)on the handset and pressing (MUTE)on the base unit. OK If you have canceled the handset registration at the previous base unit (p. 67), start from step 5. If you have not canceled the handset registration at the previous base unit (p. 67), the handset number still remains on that base unit memory. To erase the handset number from the previous base unit, see the base unit Operating Instructions. For KX-TG2700S base unit: (1) press (PROGRAM), (2) press (MUTE), (3) enter “335#”, and (4) enter that handset number ((1)to (8)). Press MUTE on base unit, then OK on handset to register handset OK Set base unit HRegistration --------------- Ex. Extension number 2 SPPRIVACY[-] Handset ReRegistering SPPRIVACY[2] Handset [2] RegRegistered Copy directory HInitial setting 2Way radio mode --------------- HHS registration Deregistration Canceling Registration/Re-registration
69 Useful Information For assistance, please call: 1-800-211-PANA(7262) If the Following Appear... If the unit detects a problem, one of the following messages will be displayed on the handset. Error beeps or a busy tone will sound. Display messageCause & Remedy The battery needs to be charged. Recharge the battery (p. 13). The battery has been discharged. The handset will not work. Charge the battery fully (p. 13). The handset has lost communication with the base unit. Walk closer to the base unit, and try again. • The called handset/base unit is in use. • The handset you tried to send directory items to is in use. • The handset you are calling is too far from the base unit. • The Privacy mode is on for the call you tried to join (p. 50). The called handset has not been registered to the base unit or you selected your extension number. • When you tried to register or deregister the handset, the handset and the base unit could not link for some reason, such as interference from other electrical appliances. Take the handset and the base unit away from the electrical appliances and try again. • If more than one handset is in use, you may not be able to register/deregister. Try again later. • Another handset tried to send the directory items but the transfer has been stopped (p. 42, 43). • If the radio communication between the handset and the base unit is partially impaired, this display will be shown. • If more than 3 units are in use, such as conducting an external/internal call, you may not be able to use another unit. Try again later. Recharge battery Busy Invalid Error!! No link to base. Walk closer to base and try again. System is busy. Please try again later. Charge for 15HRS
If the Following Appear... 70 Display messageCause & Remedy When trying to store an item in the directory, the directory memory is full. To erase other items from the directory, see page 41. • When the displayed item is being sent to the destination handset, the directory memory is full. The transfer is stopped. If you tried to send all of the items, the item displayed with “---Incomplete---” and items after it have not been transferred to the destination handset. You can press (OFF)to exit the mode (p. 42, 43). To erase other stored items from the destination handset directory, see page 41. You can send all of the items again or send the items which have not been transferred one by one (p. 42, 43). • If the transfer is stopped for another reason, “Directory full” will not display, for example: – the destination handset may be out of area, or – the destination unit user may press or . Although you tried to send your directory items to another handset, your directory is empty. • When you call the handset or base unit to monitor, the Room Monitor mode of the destination unit is set to off (p. 51). • The called handset is on the base unit. The handset must be off the base unit to be monitored. When you tried to call another handset in the 2-Way Radio mode; – the handset is too far from your handset. Walk closer to the handset. – 2-Way Radio mode on the handset is off (p. 53). – The called handset is talking with another handset in the 2-Way Radio mode. Directory DirectFull Directory No items stored Not found 2Way radio mode Denied ---Incomplete--- Tom Jones 098-765-4321 Directory full (The name/number is an example.)