Panasonic Kx Tg2700 Operating Instructions Manual

							Installation
11
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Connections
•USE ONLY WITH Panasonic AC ADAPTOR PQLV10 (Order No. PQLV10Z).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•To connect a standard telephone on the same line, see page 64.
•If your unit is connected to a PBX which does not support Caller ID and voice
mail services, you cannot access those services.
Hook
Telephone Line CordAC AdaptorPower Outlet (AC 120 V, 60 Hz)
Single-Line Telephone Jack (RJ11C)Fasten the AC adaptor cord to 
prevent it from being 
disconnected.
Raise the antennas. 
						

							Installation
12
Installing the Battery in the Handset
Insert the battery into the handset as shown, matching the correct polarity
(#). Press the battery down until it places into the compartment ($).
When finished, close the cover.
1
2
Battery strength
You can check the battery strength on the handset display.
The battery strength is as shown in the chart below.
Display promptBattery strength
Fully charged
Medium
Low
Needs to be recharged.
Discharged
Battery Charge
Place the handset on the base unit and charge for
about 15 hoursbefore initial use.
•The CHARGE indicator lights, a beep sounds and
“Charging” will be displayed. 
CHARGE Indicator 
						

							13
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Recharge
Recharge the battery when:
—
“Recharge battery” is displayed on 
the handset,
—“ ” flashes on the display, or
—
the handset beeps intermittently while it is in use.
•If you DO NOT recharge the handset battery for more than 15 minutes, the display
will continually indicate “Recharge battery” and/or “” will flash when the
handset is lifted off the base unit.
•If the battery has been discharged, the handset will display “Charge for 15HRS”
and “” when you place the handset on the base unit. The handset will not
work. Keep charging.
SPPRIVACY[1]
Recharge battery
Battery information
After your Panasonic battery is fully charged (p. 12):
When using the 2-Way Radio mode (p. 53) with the battery fully charged:
•The battery operating time may be shortened depending on usage conditions and
ambient temperature.
•Clean the handset and the base unit charge contacts with a soft, dry cloth
once a month. Clean more often if the unit is subject to grease, dust or high
humidity.Otherwise the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the base
unit until “Recharge battery” is displayed and/or “” flashes. This will
maximize the battery life.
•The battery cannot be overcharged.
OperationOperating time
While in use (TALK)
While not in use (Standby)
While using the Reception Booster feature (p. 24)Up to 4.5 hours
Up to 11 days
Up to 3.5 hours
OperationOperating time
While in use (TALK)
While not in use (Standby)Up to 4.5 hours
Up to 12 hours 
						

							Programmable Settings
14
Programming Guidelines
This unit has programmable functions. Most of them are selected from the
function menu on the display (p. 15).
How to select a function item from the menu
Make sure the handset is not being used.
1. Press 
(CONF/FUNCTION). 
•The main menu is displayed (p. 15).
2. You can scroll through the menu by pressing
Öor Ñ. Scroll to the desired item by
pressing 
Öor Ñ.
3. Press 
áto select the item.
4. If the item has a sub-menu I, it will be 
displayed. Select the sub-menu item by 
pressing 
Öor Ñ, and press á.
If the sub-menu Iitem has the sub-menu II, 
it will be displayed. Select the sub-menu IIitem in the same way. 
5. You can then select the desired setting by
pressing 
Öor Ñ.
6. To save the setting, press the right soft key
().
•When programming is complete, a confirmation tone sounds. The display will
return to the main menu or the sub-menu 
Ior the sub-menu II(if the function
item is in the sub-menu 
Ior in the sub-menu II). You can continue programming
other items. To exit the menu, press (OFF).
Useful information:
•“---------------” indicates the beginning or end of the function menu.
•
You can go back to the previous display by pressing Üexcept when entering characters
or numbers. To return to the main menu from the sub-menu 
Ior sub-menu II, press Ü.
SAVE
The right soft key works as
the key when
“” displays above it.
SAVE
SAVE
Navigator key has four active
areas that are indicated by
arrows. The key is indicated
by the arrows Ñ, Ö, Üor
áin the Operating
Instructions.
Save directory
HRinger setting
Copy directory
Ringer volume
HRinger tone
Incoming call
Ringer tone
:1GFSAVE
---------------
HSave directoryRinger setting
SAVE
(OFF)
(CONF/FUNCTION)
Ex. Ringer tone setting 
						

							15
Preparation
For assistance, please call: 1-800-211-PANA(7262)
•You can exit the programming mode any time by pressing (OFF).
•If you do not press any buttons for 60 seconds, the handset will exit the
programming mode.
•If the unit detects a problem, an error message will be displayed (p. 69).
Function Menu Table
You can use the following functions to customize your unit. After pressing
(CONF/FUNCTION), the main menu is displayed. Most items in the main
menu have a sub-menu I. The sub-menu Iis shown after selecting the
item in the main menu. If the sub-menu Iitem has the sub-menu II, it will
be displayed after selecting that sub-menu Iitem. See the corresponding
pages for function details.
Save directoryp. 37
Ringer setting
Copy directory
Initial setting
p. 19
p. 60
p. 61Ringer volume
Ringer tone
Incoming call
p. 42Copy 1 item
p. 43Copy all items
p. 20LCD contrast
p. 18Auto talk
p. 51Room monitor
p. 33Caller ID edit
Set tel line
Registration
p. 16Set dial mode
p. 59Set flash time
p. 17Set line mode
Voice mailp. 56VM tone detect
p. 55Save VM access#
Set base unitp. 61Incoming call
p. 51Room monitor
p. 68HS registration
p. 67Deregistration2Way radio modep. 53
Main menuSub-menu ISub-menu II
(for Handset)
(for Base unit) 
						

							Programmable Settings
16
Dialing Mode
If you have touch tone service, set to “Tone”. If rotary or pulse service is
used, set to “Pulse”. Your phone comes from the factory set to “Tone”.
Make sure the base unit and the handset are not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ.
3
Press á.
4
Scroll to “Set tel line” by pressing Ö
or Ñ.
5
Press á.
6
Press áat “Set dial mode”.
•The current setting is displayed.
7
Select “Pulse” or “Tone” by pressing Öor
Ñ.
8
Press the right soft key ( ).
•A beep sounds.
•To exit the programming mode, press (OFF).
•You can exit the programming mode any time by pressing (OFF)
.
SAVE
Set dial mode
:ToneGFSAVE
Caller ID edit
HSet tel line
Voice mail
---------------
HSave directory
Ringer setting
Copy directory
HInitial setting
2Way radio mode
---------------
HLCD contrast
Auto talk
---------------
HSet dial mode
Set flash time
Set dial mode
:PulseGFSAVE
Set dial mode
:Pulse 
						

							17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Line Mode
If the line is connected to a low voltage system such as a PBX, set to “B”.
Your phone comes from the factory set to “A”. 
Make sure the base unit and the handset are not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ,and press á.
3
Scroll to “Set tel line” by pressing Ö
or Ñ.
4
Pressá.
5
Scroll to “Set line mode” by pressing Ö
or Ñ.
6
Press á.
•The current setting is displayed.
7
Select “B” or “A” by pressing Öor Ñ.
8
Press the right soft key ( ).
•A beep sounds.
•To exit the programming mode, press (OFF).
•You can exit the programming mode any time by pressing (OFF)
.
SAVE
Set line mode
:AGFSAVE
---------------
HSet dial mode
Set flash time
Set line mode
:BGFSAVE
Set line mode
:B
Set flash time
HSet line mode
---------------
Caller ID edit
HSet tel line
Voice mail
---------------
HSave directory
Ringer setting
Copy directory
HInitial setting
2Way radio mode 
						

							Programmable Settings
18
Auto Talk Feature
The Auto Talk feature allows you to answer a call by lifting the handset off
the base unit without pressing  or  . If you purchase an additional
handset (p. 21), you can answer a call by lifting it off the charger. If you
want to use this feature, turn the feature ON by programming. Your phone
comes from the factory set to OFF.
Make sure the handset is not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ.
3
Press á.
4
Scroll to “Auto talk” by pressing 
Öor Ñ.
5
Press á.
•The current setting is displayed.
6
Select “On” or “Off” by pressing Öor Ñ.
7
Press the right soft key ( ).
•A beep sounds.
•To exit the programming mode, press (OFF).
•You can exit the programming mode any time by pressing (OFF)
.
•In order to view Caller ID information after you lift up the handset to answer a call,
leave the Auto Talk feature OFF.
SAVE
Auto talk
:Off GFSAVE
Copy directory
HInitial setting
2Way radio mode
---------------
HSave directory
Ringer setting
Auto talk
:On
Auto talk
:OnGFSAVE
---------------
HLCD contrast
Auto talk
LCD contrast
HAuto talk
Room monitor 
						

							19
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Ringer Volume
Handset
You can program the handset ringer volume to HIGH, MEDIUM, LOW or
OFF. If set to OFF, the handset will not ring for external calls, and for
internal calls it will ring at the LOW level. Your phone comes from the
factory set to HIGH.
Make sure the handset is not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Ringer setting” by
pressing 
Öor Ñ, and press á.
3
Press áat “Ringer volume”.
4
Select the desired volume by
pressing 
Öor Ñ.
•Each time you press Öor Ñ, the
volume will change and ring.
•To turn the ringer OFF:
press Örepeatedly until “Off ?”
displays.
5
Press the right soft key ( ).
•A beep sounds.
To turn the ringer ON:
Press 
Ñin step 4, and press the right soft
key ( ).
•The ringer will sound at the LOW level. 
•You can exit the programming mode any time by pressing (OFF)
.
•If set to OFF,“Ringer off”will be displayed while the handset is not in use.
After receiving a voice mail message, 
“Ringer off”will not be displayed but
“Voice mail”will be displayed.
•You can also select the ringer volume while an external call is being received.
Press Öor Ñwhile the handset is just ringing.
•To adjust the ringer volume for the 2-Way Radio mode, see page 54.
•You can change the ringer tone for external calls. See page 60.
SAVE
SAVE
HIGH
MEDIUM
OFF
Save directory
HRinger setting
Copy directory
Ringer volume
Low High
Ringer volume
Low High
Ringer volume
RingngOff ?
LOW
---------------
HRinger volume
Ringer tone
Ringer volume
Low HighGFSAVE
Ñ
Ñ
ÑÖ
Ö
Ö 
						

							Programmable Settings
20
Base unit
You can set the base unit ringer volume to HIGH, MEDIUM, LOW or OFF. If
set to OFF, the base unit will not ring for external calls, and for internal calls
it will ring at the LOW level. Your phone comes from the factory set to
HIGH. Make sure the base unit is not being used.
To select HIGH (preset), MEDIUM or LOW, press (RINGER/AUTO).
•Each time you press the button, the ringer volume will change and ring.
To turn the ringer OFF, press and hold (RINGER/AUTO)until 2 beeps
sound.
To turn the ringer ON, press 
(RINGER/AUTO).
•The ringer will sound at the LOW level.
•You can also select the ringer volume while an external call is being received.
Press (RINGER/AUTO), ÖorÑwhile the base unit is just ringing.
•You can change the ringer tone for external calls. See page 60.
LCD Contrast
You can program the handset LCD contrast (6 levels). Your phone comes
from the factory set to level 3. Make sure the handset is not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ, and press á.
3
Press áat “LCD contrast”.
4
Select the desired contrast by pressing Ö
or Ñ.
•Each time you press Öor Ñ, the LCD
contrast will change. 
•The number of steps shows the LCD
contrast level.
5
Press the right soft key ( ).
•A beep sounds.
•To exit the programming mode, press (OFF).
•You can exit the programming mode any time by 
pressing (OFF)
.
SAVE
---------------
HLCD contrast
Auto talk
LCD contrast
Low HighGFSAVE
LCD contrast
Low High
LCD contrast
Low High
Level 6
Level 4
Level 1
Copy directory
HInitial setting
2Way radio mode