Panasonic Kx-Td500 Features Guide

Conference 
DescriptionThe system supports 3-party conference calls which include out-
side and/or inside parties.  During a 2-party conversation, the
extension user can add a third party to their conversation, thereby
establishing a conference.
Conditions¥Conference call arrangements
A conference call can be one of the following three arrangements:
1-inside and 2-outside; 2-inside and 1-outside; and 3-inside.
¥Conference trunk
Up to eight conference calls are available simultaneously at a time by...

Conference, Unattended  
DescriptionA PT user who originated a conference call with two outside par-
ties can leave the conference for a while to allow the other two
parties to continue conversation.  This is called an Unattended
Conference.  The conference originator may return to the confer-
ence, if desired.
Conditions¥Class of Service
An Unattended Conference cannot be established unless the extension
is allowed to transfer a call to an outside party by COS programming.
¥Call duration limit
The...

Confirmation Tones
DescriptionConfirmation tone indicates an action was accepted by the system,
and the extension user can proceed to the next operation.
At the end of various operations, the extension user can confirm
the success of the operation by hearing a confirmation tone.
Confirmation tone 1: 
(a) Indicates that the new setting differs from the previous setting.
(b) Set or cancel the Electronic Station Lockout.
Confirmation tone 2:
(a) Indicates that the new setting is identical to the previous...

Confirmation tone 4: 
Sent when a 2-party call is changing to a 3-party call and vice
versa.  (These are caused by Executive Busy Override, Barge-in,
Conference, or Privacy Release.)  It is possible to eliminate this
tone by System Programming
.
Conditions¥ Confirmation Tone 1 and 2 are provided to reconfirm the assigned fea-
ture.
Programming References
System Programming................................Installation Manual, Section 4
4.2.1  System - Tenant
Ñ External Paging Tone
4.2.7  System - System...

Consultation Hold
DescriptionAllows an extension user to place a call on hold temporarily on
purpose to transfer it, to make a Conference call, or to perform
Call Splitting.  
A
 PT usercan place a call on Consultation Hold by pressing
TRANSFER or CONF button.
An SL
T usercan place a call on Consultation Hold by pressing the
switchhook lightly only to transfer it.
Conditions¥ The following calls cannot be placed on Consultation Hold.
Ñ Doorphone calls
Ñ Paging
¥ 
A new incoming call will not come in on...

Features GuideD
Features Guide 87
Data Line Security
DescriptionOnce Data Line Security is set on the extension, communication
between the extension and the other end is protected from any sig-
nal such as Call Waiting, Hold Recall and Executive Busy
Override.  Data equipment or a facsimile may be connected to an
extension port so that the extension user can perform data commu-
nications.  During communication, Data Line Security maintains
secure data transmission against tones or interruptions from...

DFeatures Guide
88 Features Guide
Dial Tones, Distinctive 
DescriptionThe following four types of dial tone patterns are provided to give
information about features activated on the extension.  
Dial tone 1:  Normal dial tone.  None of the features listed below 
are activated.
Dial tone 2:  Emitted when any one of the features below are set.
¥Absent Message Capability
¥Background Music (BGM)  
¥Call Forwarding 
¥Call Pickup Deny 
¥Call Waiting 
¥Data Line Security
¥Do Not Disturb (DND) 
¥Electronic...

Features GuideD
Features Guide 89
Dial Type Selection
DescriptionUsed to select the desired dialing mode for each CO line regardless
of originating call extension (rotary or tone).
There are two dialing modes available:
DTMF
 (Dual Tone Multi-Frequency) Mode
The dialing signal from an extension, either tone or rotary, is
converted to tone dialing.  DTMF signals are transmitted to
the CO line.
Pulse Dial (Rotar
y) Mode
The dialing signal from an extension, either tone or rotary, is
converted to rotary...

DFeatures Guide
90 Features Guide
Direct In Lines (DIL)
DescriptionEnables an incoming CO call to go directly to one or more answer-
ing points without assistance of the operator. 
DIL
 1:1puts an incoming CO call to a single destination.
Assignable destinations are: 
(1) Extension
(2) Floating Extension
Ñ modem (Remote Administration) 
Ñ external pager (TAFAS) 
Ñ OGM Group (DISA message)
Ñ Extension Group
Ñ DIL 1:N Group
Ñ Phantom Extension  
This CO line can be used by multiple extension users to make...

Features GuideD
Features Guide 91
Outline sketch of Direct In Lines (DIL)
DIL 1:1
Extension
(DN)
Floating Extension
(FDN)
Modem (Remote Maintenance)
External Pager (TAFAS)
OGM Group (DISA message)
Extension Group
DIL 1:N Group
Phantom Extensions
Hunting Group (Terminate)
Hunting Group (Circular)
Ring Group
Operator Group
VM (Voice Mail) Group
AA (Automated Attendant)  Group
UCD Group