Panasonic Kx Ta824 Operating Manual

1.3 Telephone Features
Operating Manual 101
To set/cancel the LCS password
To set LCS
To cancel LCS
Operation Flowchart
The operations in the shaded areas can be performed in hands-free mode.
Off-hook.
On-hook.
Enter LCS password (3 digits)
2 times to set or one time to cancel.
PT
   LCS 
password   LCS
password
   LCS 
password
Set
Cancel
77
Enter 77   .
OR
C.Tone
Enter #. 
Press Live Call 
Screening.Enter LCS password.
LCS password
PT
(Live Call
 Screening)
While on-hook
Press red Live Call Screening....

1.3 Telephone Features
102 Operating Manual
Hands-free ModePrivate Mode
Stop 
monitoringAnswer
the call
Monitor
Monitor 
No operation
Stop
monitorAnswer
(Alert Tone)
Press FLASH/RECALL 
or LCS Cancel.
OR
Press FLASH/
RECALL or 
LCS Cancel.
Stop the 
alert tone
(LCS Cancel)
Off-hook.
OR
OR
Press Live Call
Screening or 
SP-PHONE.
Press 
SP-PHONE, 
MONITOR
, 
or Live Call 
Screening.
PT
(Live Call
 Screening)
OR
Press 
FLASH/
RECALL 
or 
LCS 
Cancel. 
Off-hook.OR
During a conversation
(Call Waiting Tone)...

1.3 Telephone Features
Operating Manual 103
1.3.57 Local Carrier-based Voice Mail Service
 The Live Call Screening (LCS) button light shows the feature status as follows:
Off: LCS is off.
Flashing green rapidly: An alert tone is ringing (Private mode only).*
1
Flashing green slowly: Monitoring.*2
Red on: LCS is on.
*1 The Direct Station Selection (DSS) button light flashes red at moderate speed while an 
alert tone is ringing.
*
2 The DSS button light flashes red slowly while monitoring.
 The operator...

1.3 Telephone Features
104 Operating Manual
To listen to messages
1.3.58 Lockout
If one par ty in a conversation goes on-hook, the call between both parties will be disconnected. A reorder 
tone is sent to the off-hook party before the call is disconnected. No operation is necessary. For more 
details, refer to 1.1.79 Lockout in the Feature Manual. If your telephone company sends a special signal (Stutter dial tone) when you seize the 
outside (CO) line, this is an indication that a new message was...

1.3 Telephone Features
Operating Manual 105
1.3.59 Log-in/Log-out
To set Log-in/Log-out
Feature Manual References
 1.1.79 Lockout
You can change your status in an extension 
group (idle extension hunting group/DISA ring 
group). When you log out, incoming calls to the 
group will not ring at your extension. When you 
log back in, calls will again ring at your 
extension. (Default: Log-in)
 The Log-in/Log-out button light shows the current status as follows: 
Off: Log-in mode 
Red on: Log-out mode
 The...

1.3 Telephone Features
106 Operating Manual
1.3.60 Message Waiting
– Leaving a Message Waiting Indication
– Calling Back a Caller Who Left an Indication
 Leaving a Message Waiting Indication
To leave a message waiting indication
Programming Manual References
[PT Programming]
 [100] Hunting Group Set
 [600] Extension Group
[PC Programming]
 9.2.2 Feature settings [2-2]—Log-in / Log-out
 9.2.11 Extension Group [2-6]—Group No., Extension Hunting—Extension Hunting
Feature Manual References
 1.1.80...

1.3 Telephone Features
Operating Manual 107
To leave/cancel a message waiting indication
To cancel a message waiting indication using the MESSAGE button
 Calling Back a Caller Who Left an Indication
To check a received message and call back
PT/SLT
Off-hook.Enter 1 to leave 
or 2 to cancel.On-hook.Dial desired 
extension number. Leave
Cancel
1
2
OR07
Enter 70. 
desired
extension no.
C.Tone
Enter #.
An SLT user can enter 0 
instead of #.
PT
Off-hook.On-hook.Dial desired 
extension number.Press MESSAGE 2...

1.3 Telephone Features
108 Operating Manual
To cancel all message waiting indications left at your extension
 The MESSAGE button light or Message/Ringer Lamp shows the current status as follows: 
Off: No messages 
Red on: New messages.
 The display shows messages in the order received, starting with the selected message.

5→6→7→8→1→2→3→4
 The MESSAGE button is used to perform operations and display notifications from both 
the Message Waiting and Built-in Voice Message (BV) features. If a message has...

1.3 Telephone Features
Operating Manual 109
1.3.61 Message Waiting for Another Extension
To check a received message and call back
To cancel all message waiting indications left at another extension
You can check messages left at another extension and call back the caller simply 
by pressing the lit Message for Another Extension button, if your proprietary 
telephone (PT) is permitted through system programming. You can also clear all 
messages left at another extension.
 On your PT, you can establish...

1.3 Telephone Features
110 Operating Manual
1.3.62 Message Waiting for Another Extension Lock
You can lock message waiting indications so that other extensions cannot confirm, call back, or clear 
message waiting indications left at your extension.
To lock/unlock message waiting indications
Programming Manual References
[PT Programming]
 [618] Message Waiting for Another Extension
[PC Programming]
 9.2.1 Main [2-1]—MW for Another Extension
Feature Manual References
 1.1.83 Message Waiting for Another...