Panasonic Kx Ta824 Feature Guide

3.3 PT Programming
Feature Guide 171
Entering System Programming Mode
Using a PT to perform system programming allows an authorized administrator to set a wide range of PBX 
features and parameters. To enter system programming mode, the system password is required. With the 
system password, all system programming is accessible.
Note
 means default value throughout these programming instructions.
Entering Manager Programming Mode
Using a PT to perform manager programming allows the manager extension...

3.3 PT Programming
172 Feature Guide
Entering Characters
The PTs dialing buttons can be used to enter characters when storing a name or message. The following 
table depicts the available characters:
* This character is only available for the KX-T7730/KX-T7735.
[Example of Entering Characters]
To enter Ann:
Notes
 To move the cursor right, press .
 To delete all characters, press CLEAR. To delete a character, press .
Times (Pressing 
SELECT)
Buttons
14
1
2536
2
3
4
5
6
7
8
9
A
D
G
J
M
P
T
$ ?
a Bb Cc
d...

3.3 PT Programming
Feature Guide 173
List of Abbreviations
AAAAutomated Attendant
APTAnalog Proprietary Telephone
BBGMBackground Music
BVBuilt-in Voice Message
CCOOutside (CO) Line
COSClass of Service
CPCCalling Party Control
DDILDirect In Line
DISADirect Inward System Access
DNDDo Not Disturb
DSSDirect Station Selection
DTMFDual Tone Multi-Frequency
EEFAExternal Feature Access
GGRPGroup
IIRNAIntercept Routing—No Answer
LLCSLive Call Screening
OOGMOutgoing Message
PPTProprietary Telephone
SSLTSingle Line...

3.3 PT Programming
174 Feature Guide
3.3.2 Programming Procedures
Notes
 means default value throughout these programming instructions.
 means to select All throughout these programming instructions.
 The following are displayed when you store a number, such a telephone number, or feature 
number:
 
P: PAUSE; -: CONF; F: FLASH/RECALL; [ ]: INTERCOM 
x: PAUSE (substitutes for any number [i.e., wild card])
 To return to the previous programming item, press .
 To correct a wrong entry, press CLEAR and...

3.3 PT Programming
Feature Guide 175
Notes
 An Outside (CO) Line Access number (9, 81 through 88) should be included before the phone 
number.
 When storing an account code assigned in Account Code [310], enter  and the account code 
after an Outside (CO) Line Access number.
Feature & Programming References
1.6.1 Memory Dialing Features
System Password [002]
WARNING
To maintain system security, a password is required to perform system programming. 
To avoid unauthorized access and possible fraudulent...

3.3 PT Programming
176 Feature Guide
DSS Console Jack Assignment [003]
Notes
 To delete (disable) an extension jack number, press CLEAR in the extension jack number step.
 The same jack number cannot be assigned to 2 DSS Consoles.
 Do not assign extension jack 01 (manager extension) as the DSS Console jack.
 The extension jack number preassigned as a paired telephone in Console Paired Telephone [004] 
should not be assigned in this program.
Feature & Programming References
1.17.1 Fixed Buttons
2.1.1...

3.3 PT Programming
Feature Guide 177
Note
With Transfer: Press the DSS button to transfer an outside (CO) line call. 
Without Transfer: Press the TRANSFER button, then the DSS button to transfer an outside (CO) line 
call.
Feature & Programming References
1.10.1 Call Transfer
1.17.1 Fixed Buttons
Time Service Switching Mode [006]
Feature & Programming References
2.2.3 Time Service
Time Service Start Time [007]
Time Service Start Time [007]
Notes
 This program is available when switching mode is enabled...

3.3 PT Programming
178 Feature Guide
Operator Assignment [008]
Note
To delete (disable) an extension jack number, press CLEAR in the extension jack number step.
Feature & Programming References
2.2.4 Operator/Manager Features
Extension Number [009]
Note
The same extension jack number may not be entered 2 times.
Feature & Programming References
1.5.1.1 Intercom Call
2.3.4 Feature Numbering
LCD Time Display [010]
Note
The following settings and features use 12-hour format even if 24-hour format is assigned...

3.3 PT Programming
Feature Guide 179
System Speed Dialing Name [011]
Feature & Programming References
1.6.1.5 Speed Dialing—Personal/System
3.3.1 Programming Instructions—Entering Characters
KX-T7710 One-touch Dialing [013]
Notes
 Any feature number can be stored in a One-touch button. However, the feature numbers for 
Personal Speed Dialing and System Speed Dialing do not function.
 This feature is not available when the KX-T7710 is connected in parallel with a PT.
Feature & Programming References...

3.3 PT Programming
180 Feature Guide
Extension Group [600]
Hunting Type [101]
Note
This program is available when the extension group is enabled in Hunting Group Set [100].
Feature & Programming References
1.2.1 Idle Extension Hunting
DTMF Integration Port [102]
Feature & Programming References
1.18.2 Voice Mail Inband (DTMF) Integration
DTMF Integration [103]
Note
If a KX-TVS series VPS/KX-TVA series VPS is connected to the PBX, select Enable in this program, 
so that Inband (DTMF) Integration between...