Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

4.2 System Programming
Hunting Group Set
100
System Programming  4-23
DescriptionAssigns to enable or disable the station hunting feature for each
extension group.
Selection• Extension group number: 1 – 8, ( = all extension groups)
• Disable / Enable
DefaultAll extension groups — Disable
Programming1.Enter 100.
Display: Hunting Group
2.Press NEXT.
Display: Group NO? ®
3.Enter an extension group number.
Pressing NEXTalso can enter extension group number 1.
Display example: Group1:Disable
4.Keep pressing...

4-24 System Programming
4.2 System Programming
Station Hunting Type
101
DescriptionUsed to set the Station Hunting type for each extension group.
There are two Station Hunting types available: Circular and
Terminating. If circular is assigned for a group, all of the extensions
in the group are searched one time until an idle one is found. If
terminating is assigned, searching stops at the extension which has
the highest jack number in the group.
Selection• Extension group number: 1 – 8,  ( = all...

4.2 System Programming
Voice Mail Port for KX-TVS75/KX-TVS100
102
System Programming  4-25
DescriptionEnables or disables the jacks which work as the voice mail ports for
DTMF transmission to the Panasonic Voice Processing System
(KX-TVS75/KX-TVS100).
Selection• Jack number: 07 / 08 / 15 / 16,  ( = all jacks)
• Enable / Disable
DefaultAll jacks — Disable
Programming1.Enter 102.
Display: VM Port
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 07.
Display...

4-26 System Programming
4.2 System Programming
DTMF Integration for KX-TVS75/KX-TVS100
103
DescriptionEnables or disables the system to send codes (DTMF tones) to
indicate the status of a call (busy, answered, ringing, disconnected,
etc.) in addition to the normal call progress tones. These codes
enable the Panasonic Voice Processing System
(KX-TVS75/KX-TVS100) to immediately recognize the current
status of the call and speed up the call handling.
SelectionEnable / Disable
DefaultDisable...

Call StateConditionsCode
4.2 System Programming
DTMF Integration (contd.)
103
System Programming  4-27
1
2
3
4
5
6
7
8
9
#9Ringback Tone
Busy Tone
Reorder Tone
DND
Answer
Forwarded to
Voice Processing
System (Ringing)
Forwarded to
Voice Mail (Busy)
Forwarded to
Extension
Confirmation Tone
DisconnectWhen an extension the Voice Processing System has
dialed is ringing.
When an extension the Voice Processing System has
dialed is busy.
When the Voice Processing System has dialed an
invalid extension number or...

Operation
4-28 System Programming
4.2 System Programming
Hold Mode Selection
104
Hold Mode To hold To transfer
Hold-1
Hold-2
Hold-3
DescriptionAssigns the call hold mode for single line telephones.
Each mode is explained as follows.
SelectionHold-1 / Hold-2 / Hold-3
DefaultHold-1
Programming1.Enter 104.
Display: Hold Mode
2.Press NEXT.
Display example: Hold-1
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferencesSection 3, Features...

4.2 System Programming
Conference Tone
105
System Programming  4-29
DescriptionAssigns whether or not a confirmation tone is sent before starting
and ending a conference call. This assignment also works for the
Executive Busy Override feature.
SelectionEnable / Disable
DefaultEnable
Programming1.Enter 105.
Display: Conference Tone
2.Press NEXT.
Display example: Enable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferenceSection 3,...

4-30 System Programming
4.2 System Programming
External Paging Access Tone
106
DescriptionUsed to remove the confirmation tone for the external pager. The
default setting sends confirmation tone to the external pager before
paging is sent.
SelectionEnable / Disable
DefaultEnable
Programming1.Enter 106.
Display: Ext-Pag Ack-Tone
2.Press NEXT.
Display example: Page:Enable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• The external pager is a...

4.2 System Programming
DTMF Receiver Check
107
System Programming  4-31
DescriptionEnables or disables the DTMF receiver to check whether the DTMF
receivers are activated normally or not.
Six DTMF receivers work with the following cards.
DTMF-R 1 and 2 — basic extension card (jacks 01 – 08)
DTMF-R 3 and 4 — extension expansion card 1 
(jacks 09 – 16)
DTMF-R 5 and 6 — extension expansion card 2 (jacks 17 – 24)
Selection• DTMF Receiver number: 1 – 6
• Enable / Disable
DefaultAll DTMF receivers — Enable...

4-32 System Programming
4.2 System Programming
Flash Mode for a Station Locked Extension
108
DescriptionAssigns whether or not an extension where the electronic station
lockout or remote station lock control feature has been set, can send
a flash signal during a conversation with an external party.
SelectionEnable / Disable
DefaultDisable
Programming1.Enter 108.
Display: Locked Ext Flash
2.Press NEXT.
Display example: FLASH:Disable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press...