Panasonic Kx-T30810 Installation Manual

							until the desired mode appears 
~-.----.---.-~I 
[24] [NEXT] [SELECT] [MEMORY][END] 
s 
For telephone instruments that have automatic 
busy tone detection, it is suggested that busy 
tone type (I) is to be used. 
Selection 
of busy tone type (I) insures that the 
camp-on feature of the Panasonic ITS phones 
will operate. Because Panasonic ITS phones are equipped 
with automatic busy tone detection in the 
speakerphone mode, calls will be terminated 
upon hearing a busy tone signal of tone type 
(2) therefore camp-on feature will not be 
activated. 
e 
See page 5-17. 
“BUSY TONE SELECT” will be displayed. 
a Press the NEXT button. 
“TONE: 1” will be displayed and “1” will 
blink. 
3. Press the SELECT button to alternate be- 
tween “TONE:l” and “TONE:2”. 
* Press the MEMORY button. 
The blinking LCD will stop. 
5. To return to the initial program mode, press 
the END button. 
2-32  
						

							I.. .._____________........~~~.....~..~~ until the desired time appears 
[25] 
[NEXT] [SEI L -r 
2-33  A tone indication will be heard at the holding 
extension to remind user that he still has a call 
on hold. 
The reminder will be sounded after 3 minutes 
but can be changed. 
There are 9 choices ranging from (1) minute to 
(9). 
, 
1. Dial (25). 
“AUTO HOLD ALARM” will be display- 
ed. 
. Press the NEXT button. 
“TIME: 3 MIN” will be displayed and “3” 
will blink. 
. Repeatpressing the SELECT button until the 
desired time is displayed. . Press the MEMORY button. 
The blinking LCD will stop. 
. To return to the initial program mode, press 
the END button. 
s 
The hold time reminder is activated, even if the 
hold recall time set is programmed to “DIS- 
ABLE”. 
xample: 
4 minutes= 
[25] [NEXT] [SELECT] 
.$? [MEMORY] [END] 
e 
See page 5-17.  
						

							[26] [NEXT] [SEI . . . . ..__......._.............. 
until the desired time appears 
ECT] [MEMORY] [END] 
When the handset of the holding extension is 
replaced on calls, you may have automatic hold 
recall after the desired time elapses. 
The hold recall time set can be removed 01 
added at customer’s request. 
. Dial (26). 
“HOLD RECALL TIME” will be display- 
ed. 
Example: 
1.5 minutes=[26] [NEXT] [SELECT] 
[SELECT] [MEMORY] [END] 
e 
See page 5-17. 
2. Press the NEXT button, 
“TIME: 30 SEC” will be displayed and “30 
SEC” will blink. 
3. Repeat pressing the SELECT button until the 
desired time (30 SEC, 1 MIN, 1.5 MIN, 2 
MIN, DISABLE) is displayed. 
. Press the MEMORY button. 
The blinking LCD will stop. 
5. To return to the initial program mode, press 
the END button. 
2-34  
						

							[27] [NEXT] [SELECT] [MEMORY] [END] 
Exatnple: 
The ackuorrjledge totle that is heard after acces- 
sitlg the extertlal pagitlg cat1 he removed or 
added at the customer’s request. To elimirzate the pagirzg access tone. 
[27] [NEXT] [SELECT] [MEMORY][END] 
a Dial 127). 
“EXT-PAG ACK-TONE” will be display- 
ed. 
. Press the NEXT buttor?. 
“ENABLE” will be displayed and blink. 
, 
3. Press the SELECT button to alteixate be- 
tweet1 ENABLE atld DISABLE to select the 
desired mode. 
s Press the MEMORY button. 
The blinking LCD will stop. 
5. To returrl to the irlitial program mode, press 
the END buttorl. 
e 
See page 5-17. 
2-35  
						

							until the desired mode appears 
r----------- I 
I 
1291 [NEXT] [SE&T] [MEMORY] [END] 
Set to “WITH 1” for Toll Restriction in some 
area where it is need to dial 1 to toll call (long 
distance). m Dial (29). 
“TOLL PREFIX” will be displayed. 
Example: 
You are required to insert a dial “1” before 
dialing the area code for long distance call. 
l-201 -348-7000 
i---. area code . Press the NEXT button. 
“WITH 1” will be displayed and blink. 
3. Press the SELECT button to alternate 
between “WITHOUT 1” and “ WITH 1” 
to select the desired mode. 
Set to “WITHOUT 1” in area where dial “I” is 
not need. e Press the MEMORY button. 
The blinking LCD will stop. 
To return to the initial program mode, press 
the END button. 
See page 5-l 7. 
2-36  
						

							r----- 
until the desired mode appears - 
------~,_;.,, 
[30] [NEXT] [SELECT] [ME 
2-37 
When you dialed on outside line by speed 
dialing, the dialed number can be secret. 
The dialed number will not be displayed on the 
LCD 
of the KX-T30830. 0 Dial (30). 
“SECRET AUTO DIAL” will be dis- 
played. 
. Press NEXT button. 
“NO SECRET” will be displayed and 
blink. 
3. Press the SELECT button to alternate 
between “NO SECRET” and “SECRET” 
to select the desired mode. 
Q Press the MEMORY button. 
The blinking LCD will stop. 
* To return to the initial program mode press 
the END button, 
e 
See page 5-17.  
						

							To operate this system, after making program changes, set the System Program Switch located on the KX-T30810 
(Electronic Modular Switching System) to the SET position. 
When the unit is unused, the Liquid Crystal Display will show the month, day and the present time. 
Using the Handset ands-free 
NO. 
El 
LIFT THE PRESS THE 
PRESS PRESS THE TALK PRESS 
HANDSET DSS BUTTON 
“SP-PHONE” 
DSS BUnON “SP-PHONE” 
(11 through 18) 
(11 through 18) 
You may dial the extension number (11 through 18) instead of pressing the DSS button. 
You may press the ICM button instead 
of the first SP-PHONE button. 
DSS- Direct Station Selection (extension I1 through 18) 
lCM--Intercom 
To Dial Another Extension Again without 
While having a conversation; 
NO. 
El The original conversation will be terminated and another extension can be dialed. PRESS ANOTHER 
DSS BUTTON 
esc 
Station to station dialing within the KX-T30810 
system. 
To dial another extension again without haaging up 
e having a conversation, 
press the DSS button. 
Using the handset 
1. Lift the handset. The original conversation will be terminated 
and another extension can be dialed. 
2. Press the DSS button. 
a called party has the KX-T30830 
. Hang up upon completion 
of the conversa- 
tion. equtpped with the LCD, an extension number of the calling party will be displayed on the 
LCD 
of the called party. 
ands-free 
. 
Press the SP-PHONE or ICM button. An extension number 
of the calling party will 
be displayed on the LCD 
of the KX-T30830. 
You can not use the DSS button whose 
2. Press the DSS button. 
3. Start talking indicator has been already lighting since any- 
one is using the extension. 
The ICM indicator will be lit green while using 
the 
unit. 
. Press the SP-PHONE button. 
You may dial the extension number (I/ through 
18) instead qf pressing the DSS button. 3-1 
-  
						

							atic CC@SS 
r 
DIALTHE PHONE 
NUMBER TALK HANG UP OR 
PRESS “SP-PHONE”  LIFT THE HANDSET DIAL “9” WAIT FOR THE CO. 
ClR PRFSS DIAL TONE _ - . . “SP-PHONE” 
es 
Each extension can automatically select an idle 
CO (Central Ofice) Line within the KX- 
T30810. 
s Lift the handset or press the SP-PHONE 
button. 
. Dial (9). 
Dial tone from CO (Central Of/ice) will be 
heurd. 
I 
3. Dial the phone number. 
. Start talking. 
5. Hang up or press the SP-PHONE button 
upon completion of the conversation. 
s 
9 dialed, will be displayed on the LCD of the 
KX-T30830 and you will hear followings. 
Dial tone from CO: indicates that the CO 
Line is captured. 
Busy tone: indicates that the three CO Lines 
are busy. 
Reorder tone: indicates that the extension is 
denied access outside line. 
The CO indicator will be lit green at your 
extension and lit red at other extensions. 
LIFT THE 
HANDSET 
DIAL THE PHONE 
NUMBER 
atlds-free 
L 
, PRESS 
“CO” 
TALK 
PRESS 
“CO” 
PRESS 
“SP-PHONE” HANG UP 
the 3 CO’s may be directly selected. 
Press the CO button. 
Dial tone from CO will be heard. 
. Dial the phone number. 
. Start talking. 
5. Hang up. 
ands-free 
0 Press the CO button. 
Dial tone from CO will be heard. 
. Dial the phone number. 
3. Start talking. 
. 
Press the SP-PHONE button. 
The phone number dialed will be displayed on the 
LCD of the KX-T30830. 
You can not use the CO button whose indicator 
has been already lighting red since anyone is using 
the CO line.  
						

							LFITHEHANDSET 
DlAL8 DIALTHECO 
ORPRESS NUMBER 
SP-PHONE (1 through 3) 
SP-PHONE 
escr 
Any of the 3 CO Lines may be selected by dial 
access. 
Lift the handset or press the SP-PHONE 
Dial (8) and the CO number (1 through 3). 
Dial tone from CO (Central Office) will be 
heard. 
. Dial the phone number. 
. Start talking. , 
5. Hang up or press the SP-PHONE button. 
ne number dialed will be displayed on 
the LCD of the KX-T30830. 
Individual line access codes 
Dial 81 for CO 1 
Dial 82 for CO 2 
Dial 83 for CO 3 
wit * 
While having a conversation, 
L 
3 
PRESS 
ANOTHERC0 
The original conversation will be terminated 
and new CO line can be accessed. 
3-3 
LIFTTHEHANDSET OR PRFSS I, - - - SP-PHONE PRESS 
AUTO DIAL THESPEED 
ACCESSCODE 
(OOthrough99) 
You may press the CO button to select the 
CO line directly after lifting the handset ot 
pressing: the SP-PHONE button. 
esc 
There are 100 memory locations of system speed 
dialing available. 
d. Lift the handset or press the SP-PHONE 
button. 
. Press the AUTO button. 
3. Dial speed access code. 
You may press the CO button to select the 
CO line directly after lifting the handset or 
pressing the SP-PHONE button. 
The dialed nutnber will be displayed on the 
D of the KX-T30830. 
‘ontinuous use of speed dial is possible. 
ex. [AUTO] [O] [Ol [AUTO] [O] [l] 
The combination of speed dialing, one touch 
dialing and manual dialing is possible.  
						

							Be sure the handset is in the cradle and the SP-PHONE button is OFF. 
Set the MEMORY switch 
of the KX-T30830, KX-T30820 or KX-T30850 to “PROGRAM”. 
PRESS DlAL9 DIALTHE 
PRESS PRESS PRESS 
PROGRAMMABLE PHONE PRESS 
MEMORY PROGRAMMABLE CLEAR 
FEATURE NUMBER 
FEATURE (TRANSFER)>> MEMORY 
You may dial 81 through 83 instead of 9. 
9 Each extension can automati- The TRANSFER button is used as the CLEAR 
button. 
cally select an idle CO line. 
81 through 83. Each extension can select a 
CO line designated. 
[9 or 81 through 83 must be dialed 
for storage. ] 
After programming all the numbers, return 
the MEMORY switch to “SET”. 
To Correct an Error while Propramming 
q 
TRANSFER After pressing the CLEAR 
button, reprogram the cor- 
rect number. 
PRESS The TRANSFER button is 
CLEAR(TRANSFER) used as the CLEAR button. INSTEADOF 
MEMORY 
I 
To Chanae a Stored Number 
Repeat “Storage” above. 
L-----l - 
LIFTTHEHANDSET PRESS 
ORPRESS PROGRAMMABLE 
SP-PHONE FEATURE 
may press the CO button to select the 
CO line directly after lifting the handset or 
pressing the SP-PHONE button. 
3-4