Panasonic Kx-T30810 Installation Manual

							Setting 
.IFTTHEHANDSET 
IRPRESS 
SP-PHONE DIAL741 # 
HANGUPOR 
PRESS 
SP-PHONE 
To Cancel 
I IFTTHEHANDSET 
IRPRESS 
SP-PHONE I DIAL740 # 
I I 
HANGUPOR 
PRESS 
SP-PHONE 
This feature provides secuiity when transmitting 
data through an extension 
of KX-T30810. 
Call waiting tone or hold time reminder tone 
from KX-T30810 are prohibited in this mode. 
1. Lift the handset or press the SP-PHONE 
button. 
2. For setting, dial (741#) and wait 
for con- 
firmation tone. 
For cancellation, dial (740#) and wait 
for 
confirmation tone. 
3. Hang up or press the SP-PHONE button. 
7Re parallel connection 
of the KX-T3083Ol 
KX-T30820 and a data terminal equipment is 
impossible. 
3-34 Programming 
When the called line is busy or while you are 
speaking on the CO Line; 
Dialing 
PRESS 
AUTO PRESS 
SNR 
LIFT THE HANDSET 
OR PRESS SNR 
SP-PHONE 
The desired phone number on an outgoing call 
to CO Line can be stored and then redialed. 
on the CO Line or when the 
called party is busy. 
1. Press the AUTO button. 
2. Press the SNR button. 
The phone number can not be stored even 
if 
you press the AUTO and SNR buttons after 
hang up. 
Lift the handset or press the SP-PHONE 
button. 
. Press the SNR button. 
YOLK may press the CO button to select the 
CO line directly after lifting the handset or 
pressing the SP-PHONE button. 
digits can be stored and redialed.  
						

							(Extension I1 only) 
To enable night service: (To disable day service) 
I 1 I 
1 I I 
LIFTTHE HANDSET 
DIAL “782#” HANG UP OR 
OR PRESS 
PRESS 
“SP-PHONE” 
“SP-PHONE” 
To disable night service: (To enable day service) 
LIFTTHE HANDSET 
OR PRESS 
“SP-PHONE” DIAL “781#” HANG UP OR 
PRESS 
“SP-PHONE” 
Normal system operation is set for day time. 
Night service allows for the outward dialing and 
incoming ringing assignments to be rearranged 
via programming. 
Night service is enabled or disabled through 
extension 11 using this feat&, at any time. 
Without activating this feature, the daylnight 
services are automatically switched at pre- 
determined time (9:00 AM and 5:OO PM 
for 
default time) by the internal clock if the Switch- 
ing Mode (DaylNight Service) is selected 
“AUTO” mode in the KX-T30810. 
Refer to “Switching Mode (DaylNight Service) ” 
page 2-10 and “Starting time (DaylNight Ser- 
vice)” page 2-11. 1. Lift the handset or press the SP-PHONE 
button 
of extension 11. 
2. Dial (782#) and wait 
for confirmation tone. 
Night service is enabled. 
GHT MODE” will be displayed. 
return to day service, dial (781#) and 
Hang up or press the SP-PHONE button 
mode selected will be shown by pressing the 
3-35  
						

							LIFT THE HANDSET 
OR PRESS 
“SP-PHONE” DIAL “79 #” HANG UP OR 
PRESS 
“SP-PHONE” 
Dialing (79 #) will clear the following station 
programs on an extension. 
Background Music 
Call Forwarding 
Data Line Security 
Dial Call Pickup Deny 
Do not Disturb 
d. Lift the handset or press the SP-PHONE 
button. 
, 
* Dial (79 #) and wait for confirmation tone. 
“EXT DATA CLEAR” will be displayed. 
* Hang up or press the SP-PHONE button. 
3-36  
						

							Station to station dialing within the KX-T30810 
There are 100 memory locations of system speed 
system. dialing available. 
0 through 99) 
It is no need to access a CO Ike. 
A rotary phone is not available for the speed 
calling. 
Continuous use of speed dialing is impossible. 
Automatic Line Access 
zsiot2 cat? automatically select an 
idle CO (Central Of&e) Line within the 
KX- T30810. 
er 
LIFT THE DIAL “9” WAIT FOR DIAL TELEPHONE 
HANDSET C.O. DIAL TONE NUMBER 
Individual Line Access 
Any of the 3 CO Lines may be selected by dial 
LIFT THE 
HANDSET 
access. 
DIAL “8” DIAL CO 
NUMBER 
(1 through 3) I WAIT FOR C.O. DIAL TELEPHONE 
DIAL TONE 
NUMBER 
two doorphones (KX-T30865) can be 
connected to the KX-T30810. 
oorphone I 
LIFT THE HANDSET DIAL “31” 
oorphone 2 
LIFT THE HANDSET DIAL “32” 
4-1  
						

							kSGY 
If the intercom extension or outside line yore 
have dialed is busy, you will be autor?lntical!\, 
called buck when the extension or the outside 
line becomes free using this function. 
This feature is also known as camp-on. If the extension you have dialed is busy, you can 
inform that extension that another intercom call 
is reaching by three beeps. For use of this 
feature, the other extension is required to be set 
this feature beforehand in the KX-T30810. 
DlAL”8” DIALCO 
NUMBER 
(1 through3) YOU WILL 
HEARABUSY 
TONE 
CONFIRMATION 
TONE HANGUP DIAL”6” 
For Intercom Calls 
DIALEXTENSION YOU WILL DIAL “6” CONFIRMATION HANGUP 
NUMBER HEARABUSY TONE 
(llthrough18) TONE 
When hearing a rinc back 
When intercom calls, you will hear 
the ring back tone. 
When outside calls, you will hear 
the dial tone from CO. 
.J LIFTTHE 
HANDSET 
A 
call back busy cannot be activated on an 
extension which has a call on hold. 
DIAL “1  DIALEXTENSION YOU WILL 
NUMBER 
HEARABUSY 
(11 through 18) 
TONE 
To answer your signal, .ree “Call Waiting” 
on page 4-4. 
one number dialed on an outgoing 
call to CO can be redialed. 
LIFTTHE 
HANDSET PRESS”#” 
You may dial “80” instead of pressing the “#” 
button. 
4-2  
						

							Allows extension user to retrieve a call (inter- 
or outside) on hold at any extension. 
To Park a Call 
LIFT THE 
HANDSET 
LIFT THE HANDSET 
DIAL “40” FLASH 
HOOKSWITCH CONFIRMATION 
TONE REPLACE 
HANDSEl 
Do not depress hookwitch for more than one 
second, or party will be disconnected. 
To Retrieve a Parked Call at Any Other Extension 
LIFT THE 
HANDSET DIAL “5” DIAL PARKED 
EXTENSION 
NUMBER 
LIFT THE 
HANDSET 
4-3  
						

							to leave your phone unattended but 
want the caller you are in conversation with to 
wait, call on hold may be used. Intercom and 
outside calls may be placed on hold. 
FLASH 
CONFIRMATION 
HOOKSWITCH 
TONE 
Do not depress hookswitch for more than one 
second, or party will be disconnected. 
To Cancel 
FLASH 
HOOKSWITCH 
Allows station user to alternate between two 
parties, either intercom or outside. 
1 
FLASH DIAL SECOND CONSULT 2ND PARTY FLASH 
HOOKSWITCH PARTY IST PARTY ON HOLD HOOKSWITCH 
2ND PARTY ON HOI 
1 ST PARTY IN 
CONSULTATION mD FLASH 1 ST PARTY ON HOLD 
HOOKSWITCH 
2ND PARTY IN 
CONSULTATION 
up to a three party conference, 
(2-outsidell-inside) (I-outsidel2-inside) or (3- 
inside}. 
FLASH UIAL ZND 
CONSULT WITH FLASH DIAL “3” 
HOOKSWITCH PARTY 
2ND PARTY 
PUTS 1 ST PARTY HOOKSWITCH 3-party conference 
1 ST PARTY ( now established. 
ON HOLD 1 
ON HOLD 
old one Caller and Talk to the Other Caller 
FLASH 2ND PARTY 
HOOKSWITCH ON HOLD 
1 ST PARTY IN 
CONSULTATION 
zg tone during a conversation indi- 
cates there is a new incoming CO Line call or 
Intercom call. 
This feature required to be set beforehand in the 
KX-T30810. For programming, see page 2-24. 
WILL HEAR 
CALL WAITING 
TONE FLASH 
HANG UP 
HOOKSWITCH 
PUTS 1 ST PARTY LIFT THE 
HANDSET CONSULT NEW 
CALLER 
1 ST PARTY 
ON HOLD ON HOLD 
When you use the hold button of a standard 
telephone, above-mentioned feature is not 
available. 
To terminate the original call and talk to the 
2nd call, huq up und then l(ft 
the handset. 
(You don’t need to ,pash the hookswitch.) 
4-4  
						

							intercom calls may be transferred to 
any extension manually. 
To Transfer After Other Extension Answers 
FLASH 
HOOKSWITCH 
1 DIAL EXTENSION ANNOUNCE HANG UP 
NUMBER AND WAIT 
FOR AN 
ANSWER 
To Transfer without Announcing the Other Extension 
FLASH 
HOOKS!YlTCH DIAL EXTENSION 
NUMBER HANG UP 
If the other extension did not receive the transferred 
call within 30 seconds after the call has been 
transferred, the call will return to you. In this case: 
LIFTTHE 
HANDSET 
To change the party to whom a call is transferred 
before hanging up 
FLASH FLASH 
DIAL EXTENSION 
HOOKSWITCH HOOKSWITCH 
NUMBER 
TO RETRIEVE 
THE CALL 
ing to all extetisions. 
To Access 
LIFTTHE HANDSET DIAL “34” 
CONFIRMATION 
TONE 
PAGE 
WAIT FOR AN 
ANSWER 
AND TALK 
Page will be heard only from the 
built-in speaker of KX- T30830, 
KX-T30850 or KX-T30820. It will not 
be heard from the built-in speaker of 
standard telephone. 
ng to either of two groups. 
To Access 
For Pickup Group I 
LIFTTHE HANDSET DIAL “35” 
CONFIRMATION 
TONE 
For Pickup Group 2: 
At step 2 above, dial 36 
instead of 3.5. 
PAGE WAIT FOR AN 
ANSWER 
AND TALK 
Page will be heard only from the 
built-in speaker of KX-T30830, 
KX- T30850 or KX- T30820. It will not 
be heard from the built-in speaker of 
standard telephone. 
4-5  
						

							Allows access to external paging equipment. 
To Access 
LIFT THE HANDSEl 
DIAL “33” CONFIRMATION 
TONE 
PAGE 
WAIT FOR CONFIRMATION 
TONE AND TALK OR HANG UP 
Page will be heard from 
external paging equipment. 
To Transfer a Call to the Paged Person 
FLASH DIAL “34” 
CONFIRMATION 
HOOKSWITCH TO 
PLACE A CALL 
ON HOLD TONE 
You may dial 35,36 
or 33 instead of 34. 
PAGE WAIT FOR AN 
ANSWER 
AND HANG UP 
A page from built-in speaker or external paging 
equipment can be answered from any extension. 
LIFT THE HANDSET DIAL “43” CONFIRMATION TALK 
TONE 
4-6 s extension user to access features of the 
central office or host PBX. (example: call 
waiting feature can be supplied by central 
.) 
external feature (call waiting) can only be 
accessed when engaged on an outside call. 
The following example shows you one of the 
procedures. 
Call Waitim-Outside Line 
WILL HEAR FLASH DIAL “0” CONSULT WITH 
A CALL 
HOOKSWITCH THE NEW CALLER 
WAITING WHILE THE 
TONE ORIGINAL CALL 
IS ON HOLD 
DIAL “0” CONSULT WITH 
HOOKSWITCH THE ORIGINAL CALLER 
WHILETHE 2ND CALL 
IS ON HOLD 
i 
If the calling party on hold 
hangs up, the line is 
terminated. 
Flashing the hookswitch and dialing 0 means 
sh operation. 
KX-T30810 is connected to host PBX and 
flash operation is required, follow the proce- 
dure offlash operation which is required in the 
host PBX.  
						

							When the dialing mode is required to change a 
pulse mode to a tone mode in one dialing 
sequence, this feature is used. 
(e.g. computer-accessed long distance service) 
DIALTHE 
PHONE 
NUMBER DIALTHE 
PHONE 
NUMBER  DIAL++ # 
When you dial using this feature, you must use 
the line selected in a pulse mode. 
Phone number after dial “Ji- #” will change to 
tone mode. 
A rotary phone is not available for the 
PulselTone Conversion. 
You should press “-3c” and “#” buttons within 
10 seconds after the number 
of the long 
distance service company. 
When you use a standard telephone equipped 
with automatic dialer, be careful the follow- 
ings: 
le: Computer-accessed long distance ser- 
vice 
Local access telephone number of the alternate 
long distance service company 76.5-4321, 
Authorization no.0123456, 
Long distance no. 543-210-9876 
Pulse mode is required by local access tele- 
phone number of the alternate long distance 
Service company. 
Service 
of MCI, SPRINT, METRO or other 
systems is used. 
Set to PULSE Switch to TONE 
L-J Tone mode 
Store the long distance service company no. 
in PULSE mode, and switch to the TONE 
mode to memory the following numbers. 
4-7 
ting” (through built-in speaker) that 
is established at the called party’s extension, can 
e switched to “ Tone alterting ” (ringing). 
This 
feature required to be set beforehand in 
the KX-T30810. For programming, see page 
tary phone is not available. 
Switching to Tone Alerting 
WAITUNTILA 
CONFIRMATION 
TONEISHEARD PRESS?+ 
RING BACK 
TONE 
You should press I‘*” button within 10 
seconds after the dialing.