Panasonic Kx-T30810 Installation Manual

							IMPORTANT!!! 
Connect sure& the frame of the KX-T30810 to the earth 
ground properly to protect the unit. 
- 
II To earth ground 
I ( Fig. 2 
. Remove the buttery cover from the compartment. 
(Fig. I) 
2. Corznect the battery (included). (Fig. 2) 
3. Install the battery into the battery compartment. 
(Fig. 3) 
“Replace the battery every 5 years with 
(P-01 H- 
F2Gl). To remove connector, depress to release 
and slide (pull) mpmrt com~ector. (Fig. 2)  
						

							Holder A - 
(see step 2) 
Holder B - 
(see step 2) 
s Insert the modular plug of the tele- 
phone line cord (2-conductor wir- 
ing) into the modular jack (marked 
CO) on the KX-T30810. 
2. Place the three telephone line cords 
into Holders A and B. 
1 
I I - I 
I 
- 
- View of TEL Jack (CO) R: Rim I 
T: T&” 1 
III 
+-Use 2-conductor 
wiring cord. 
To Terminal Board or Modular Jacks 
from the Central Office (CO). 
4htiO~ 
is-~o~~ec~o~ may cause the operate i~~~o~e~ly. 
See “ 
wing Installation” page 5-1 and ” 
un’ng Connection” page 5-2 before connecting. 
I-6  
						

							. Insert the modular plug of the tele- 
phone line cord (4-conductor wir- 
ing) into the modular jack (marked 
EXT.) on the KX- T30810. 
. Place the cords into Holders A and 
View 
of TEL Jack (extension) 
L: LOW 
H: High 
4-conductor wiring is 
required for each 
extension. 
, 
To &tensions . 
The inner 2 wires (red, green) are for Tip and Ring and the outer 2 wires (black and yellow) are for Low and High 
(DA TA) . 
The max. length of the telephone line cord that connects the KX-T30810 and the extension is shown below. 
26 AWG: Under 460 feet 
24 A WC: Under 750 feet 
22 A WG: Under 1180 feet 
is-connection m erate improperly. See “During Installation” page 5-1 
and 
1-7  
						

							Holder A 
(see step 2)- 
Holder B 
(see step 2)- Insert rhe modular plug of the tele- 
phone line cord (2-conductor wir- 
ing) into the modular jack (marked 
EXT.) on the KX-T30810. 
Place rhe cords into Holders A and 
Outer 2 pins (Low and High) will not 
be used 
for Standard Telephone. 
R: Ring 
T: Tip 
View 
of TEL Jack (extension) 
--Use 2-conductor wiring 
for each extension. 
To Extensions 
The max. length of‘ rhe telephone line cord that cotltlects the*KX-T30810 atld rhe extension is shown below. 
26 AWG: Utlder 2290 feet 
24 AWG: Under 3700 feet 
22 A WG: Under 5900 feet 
[f rhe relephotle or atuwerhg machine with A-Al relay is cotlnected to rhe KX-T30810, set the A-Al relay switch of 
rhe telephotle or atuwering tnuchine to OFF. 
nection may cause the KAY-T30810 to operate improperly. 
See ‘During Installation” page 5-1 and “During Connection” page 5-2 before connecting. 
1-N  
						

							External Music Source 
I 
Adjust the sound level 
of the music on hold 
with the Volume 
I 
I control. J t 
Use a two- 
conductors plug 
(%4 inch in diameter) 
Input impedance 
5kR 
Input Level 
-10 dBm 
Use a cord that 
has the internal 
resistance 1On. 
HOTside 
+--- auxiliary plug 
(included) 
EA’R TN side 
Speaker 
Use shielded cable. 
Use RCA connector. 
Output impedance: 6000 
HOTside 
EARTH side auxiliary plug 
(included)  
						

							For installing the doorphone, uSe the Optional Doorphone Adaptor (KX-ljudovu/. 
~ HOW to install the Doorphone to the RX-T3 ^ 
-..,;nr+;nnr +n the holes 
- _ 0810 
/ 
I 
the unit. 
@push the adaptor down so that it Locks into the ribs 
-  
						

							2. Wiring connection of the Doorphone 
(A) Connect the doorphone to the terminal box using 4-conductor modular connectors. 
(B) Connect the wires 
of doorphone 1 to the red and green screws of the terminal box. 
(C) Connect the wires 
of doorphone 2 to the yellow and black screws of the terminal box. 
Doorphone Adaptor 
(KX-T3086OD) 
III 4-conductor wiring 
is required. 
Doorphone 1 (KX-T30865) 
The max. length of the telephone line cord that connects the KX-T30810 and the doorphone (KX-T30865) is shown 
below. 
26 A WG: Under 230 
feet 
24 A WC: Under 370 feet 
22 A WG: Under 590 feet 
I-11  
						

							. Connect all extension wiring to the KX-T30810. . Confirm that dialing can be done on following 
extensions using a tone telephone. 
. Confirm that dialing can be done from all the 
extensions using a tone telephone. 
(Do not exchange the extension.) Extension 11.. . CO 1 
Extension 12.. CO 2 
Extension 13...CO 3 
. 
if a dialing can not be done, the polarity between 
the extension and the KX-T30810 must be re- 
versed. 
Reverse here 7. If a dialing can not be done, the polarity between 
the KX-T30810 and the Central Ofice Line must 
be reversed. 
Reverse here 
. Set the Power Switch on the KX-T30810 to the 
8. 
If any extension is changed or replaced, repeat 
OFF position. 
these procedures (from step 1 to step 7). 
5.Connect all Central Office (CO) Lines. 
l-12  
						

							s Connect the cord from the optional KX-A16 to The Battery life is 3 years. 
the KX- T30810. A simple way to check the KX-A16 is to 
Plug in the AC power cord from the KX-A16. disconnect the KX-T30810 and the KX-A16 
0 
from the AC outlets, and then to observe if the 
. Turn on the Power Switch located on the 
KX-T30810 operates. 
KX-A16. 
Approximately 24 hours is required to recharge 
the KX-A16. 
The KX-A16 will work for approximately 4 
hours (on the average) in the event of power 
failure. If the KX-T30810 does not operate, recharge 
the KX-A16. 
AC Primary Fuse, (250 V, 1.25 A) x I: 
Replace the fuse which is in the fuse holder 
located on the rear, if the CHARGE Indicator 
is off. 
KX-T30810 
Battery B&k-up 
Connector (Keep the unit away 
from heating 
appliances.) 
BATTERY LOW Indicator: 
will be lit while recharging 
is insufj?cient. Power Switch 
CHARGE Indicator: 
will be lit while the adaptor 
is being recharged. 
l-13  
						

							To activate this system, the requirements from telephone company and the customer must be programmed once the 
Power Switch has been turned on. 
. At extension 11: 
All system programming changes (example: sys- 
tem clear, station program clear, toll restriction, 
hookswitch flash timing...) are done through 
extensiorl 11, 
. System Program Switch setting: 
The System Program Switch located on the 
KX-T30810 must be set to the PROGRAM 
position while making program changes. After all 
programming changes are completed, return the 
program switch to the SET position. 
3. Overlay: 
This overlay is used for programming the system 
and the program function names on buttons are 
inscribed on this card. Refer to page 2-2. 
. Before system programming, you may operate 
systetn clear and station program clear to set 
dqfault data of programming. 
A. System Clear: 
“SYSTEM CLEAR” will be displayed. 
ess the NEXT button. 
“ALL CLEAR?” will be displayed. 
3 Press the MEMORY button to clear system. 
4 To exit from system clear, press the END 
button. 
The following features are preset as the default 
data. 
Date and Time 
System Speed Calling 
CO Connection Assignment 
Dial Mode (TonelPulse) Selection 
Switching Mode (DaylNight Service) 
Starting Time (DaylNight Sert1ic.e) 
Flexible Day Outward Dialing Assignment 
Flexible Night Outward Dialing Assignment 
Flexible Day Ringing Assignment 
Flexible Night Ringing Assignment 
Toll Restrictiorz-C1as.r Assignment 
Toll Restriction-Area Code Selection 
Progrummable Operator Cull 
Host PBX Access Codes Assignment 
Automutic Answering (AutomaticlManuul) Preferred Line Assignment 
Programmable Call Waiting 
Duration Time Count Start Mode 
Hookswitch Flash Timing 
Disconnect Time 
Calling Party Control (CPC) Signal 
Intercom Alerting Mode 
Programmable Doorphone 
Dial Call Pickup Group Assignment 
Busy Tone Selection 
Hold Time Reminder 
Hold Recall Time Set 
Programmable External Paging Access Tone 
DTMF Receiver 
Programmable Toll PreJix 
Programmable Secret Auto Dial 
B. Station Program Clear: 
1 Dial (98). 
“EXT CLEAR” will be displayed. 
2 Press the NEXT button. 
“ALL CLEAR?” will be displayed. 
3 Press the MEMORY button to clear the 
system. 
4 To exit from station clear, press the END 
button. 
The following features are preset as the 
defuult data. 
One Touch Dialing 
Background Music 
Cull Forwarding 
Data Line Security 
Dial Call Pickup Deny 
Do not Disturb 
Selection 
2-1