Panasonic KX MB773 User Manual

							1. Introduction and Installation
11
1.2 Accessory information
To ensure that the unit operates properly, we 
recommend the use of a Panasonic toner cartridge and 
drum unit. See page 94 for specifications.
1.2.1 Available accessories
–Replacement toner cartridge*1
LModel No. (Part No.): KX-FAT92E/KX-FAT92X
–Replacement drum unit
LModel No. (Part No.): KX-FAD93E/KX-FAD93X
*1 Approx. 2,000 sheets of A4 size paper can be 
printed with KX-FAT92E/KX-FAT92X.
Find in g the  Co ntrols
1.3 Button descriptions
A{COPY}
LTo switch to the copy mode (page 22, 36).
B{SCAN}
LTo switch to the scan mode (page 22, 33).
C{COLLATE}
LTo make a collated copy (page 40).
{DIRECTORY} (KX-MB773/KX-MB783 only)
LTo initiate the navigator directory (page 41, 45).
D{CONTRAST}
LTo select a contrast (page 36, 43).
E{RESOLUTION}
LTo select a resolution (page 36, 43).
F{ZOOM}
LTo enlarge or reduce a document when copying 
(page 37).
{QUICK SCAN} (KX-MB773/KX-MB783 only)
LTo store a scanned document into memory, and 
then send it (page 44).
G{PAG E  L AYO U T}
LTo make quick ID, poster or N in 1 copy (page 38).
H{SET}
LTo store a setting during programming.
I{MENU}
LTo start or exit programming.
J{CALLER ID} (KX-MB773/KX-MB783 only)
LTo use Caller ID features (page 53).
LTo change the display of the caller information 
(page 53).
K{REDIAL}{PAU S E} (KX-MB773/KX-MB783 only)
LTo redial the last number dialled. If the line is busy 
when you make a phone call using the 
{MONITOR} button, or when you send a fax, the 
unit will automatically redial the number 2 or more 
times.
LTo insert a pause during dialling.
L{STOP}
LTo stop an operation or programming session.
LTo erase a character/number. * The small hole on the left side of the LCD display is for 
beeps (KX-MB263 only).
* The pictured model is KX-MB773/KX-MB783.
LABCDEFG HIJK
MN
QRPOSTUVW
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 11  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
12
M{FAX AUTO ANSWER} (KX-MB773/KX-MB783 
only)
LTo turn the auto answer setting ON/OFF (page 
48).
{POWER SAVE} (KX-MB263 only)
LTo set the unit to the power save mode manually.
N{FA X} (KX-MB773/KX-MB783 only)
LTo switch to the fax mode (page 22, 43).
O{BROADCAST} (KX-MB773/KX-MB783 only)
LTo send a document to multiple parties (page 45).
P{MANUAL BROAD} (KX-MB773/KX-MB783 only)
LTo send a document to multiple parties manually 
(page 45).
QStation keys (KX-MB773/KX-MB783 only)
LTo use the one-touch dial feature (page 41, 45).
RNavigator key
LTo select desired settings during scanning or 
copying (page 33, 36).
LTo adjust volume (KX-MB773/KX-MB783 only) 
(page 25).
LTo search for a stored item (KX-MB773/KX-
MB783 only) (page 45).
S{LOWER} (KX-MB773/KX-MB783 only)
LTo select stations 4–6 for the one-touch dial 
feature (page 41, 45).
T{MONITOR} (KX-MB773/KX-MB783 only)
LTo initiate dialling.
When you press {MONITOR} while receiving a 
call, you will be able to hear the other party, but 
the other party will not be able to hear you.
U{RECALL} (KX-MB773/KX-MB783 only)
LTo access special telephone services or for 
transferring extension calls.
V{TONE} (KX-MB773/KX-MB783 only)
LTo change from pulse to tone temporarily during 
dialling when your line has rotary/pulse service.
W{START}
LTo copy a document (page 36).
LTo scan a document (page 33).
LTo send or receive a fax (KX-MB773/KX-MB783 
only) (page 43, 49).
1.4 Overview
1.4.1 Front view
* The pictured model is KX-MB773/KX-MB783.
* The pictured model is KX-MB263.
1Top cover
2ADF (Auto Document Feeder) cover
3Document guides
4Document cover
5Output tray
6Top cover release lever
7Document entrance
8Paper input tray
9Recording paper exit
jDocument exit
12 43
6879j 5
14
689 5
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 12  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
13
1.4.2 Rear view
* The pictured model is KX-MB783.
Removing the shipping tape
Remove the shipping tape (1).
Note:
LShipping tape positions are subject to change 
without notice.
Installation
1.5 Toner cartridge and drum unit
The included toner cartridge is a starter toner cartridge.
Caution:
LRead the following instructions before you begin 
installation. After you have read them, open the 
drum unit protection bag. The drum unit contains 
a photosensitive drum. Exposing it to light may 
damage the drum. Once you have opened the 
protection bag:
– Do not expose the drum unit to light for more 
than 5 minutes.
– Do not touch or scratch the black drum 
surface.
– Do not place the drum unit near dust or dirt, 
or in a high humidity area.
– Do not expose the drum unit to direct 
sunlight.
LWe cannot be responsible for any damage to the 
unit or degradation of print quality which may 
occur from the use of a non-Panasonic toner 
cartridge and drum unit.
LDo not leave the toner cartridge out of the 
protection bag for a long time. It will decrease the 
toner life.
LDo not add toner to the toner cartridge.
1Before opening the protection bag of the new toner 
cartridge, shake it vertically more than 5 times.
2Remove the toner cartridge and drum unit from the 
protection bags. Peel off the seal (1) from the toner 
cartridge.
LDo not touch or scratch the black drum surface 
(2). ARecording paper guides
BSpeaker (KX-MB773/KX-MB783 only)
CHandset (KX-MB773/KX-MB783 only)
DPower inlet
EManual input tray (Rear cover)
FExternal telephone jack (KX-MB773/KX-MB783 
only)
GTelephone line jack (KX-MB773/KX-MB783 only)
HUSB interface connector
ILED (KX-MB783 only)
JLAN interface connector (KX-MB783 only)
A
FHG
B
I
JDE
C
1
12
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 13  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
14
3Place the toner cartridge (3) into the drum unit (4) 
vertically.
4Turn the green levers (5) on each side of the toner 
cartridge while pressing down firmly.
5Make sure that the triangles (6) match, to install the 
toner cartridge correctly.
6Lift the top cover release lever (7) and open the top 
cover (8).
Note:
LDo not touch the transfer roller (9).
LIf the lower glass (j) is dirty, clean it with a soft 
and dry cloth.
3
4
5
6
8
9
7
j
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 14  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
15
7Install the drum and toner unit (k) by holding the 
tabs.
LMake sure that the triangles (l) match, to install 
the drum and toner unit correctly.8Close the top cover until locked.
Caution:
LTo prevent injuries, be careful not to put your 
hands under the top cover.
To replace the toner cartridge and the drum unit
When the display shows the following, replace the toner 
cartridge.
TONER LOW
TONER EMPTY
LTo check the drum life and quality, please print the 
printer test list (page 92) and refer to page 94 for 
information on the drum life. If printing quality is still 
poor or “REPLACE DRUM” appears on the display, 
replace the toner cartridge and drum unit.
LTo ensure that the unit operates properly, we 
recommend the use of Panasonic toner cartridge 
(Model No. KX-FAT92E/KX-FAT92X) and drum 
unit (Model No. KX-FAD93E/KX-FAD93X). See 
page 11 for accessory information.
k
l
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 15  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
16
LTo maintain print quality and machine life, we 
recommend you to clean slots and openings (page 7) 
and the inside of the unit (page 88, 91) when 
replacing the toner cartridge and/or drum unit.
Waste disposal method
Waste material should be disposed of under conditions 
which meet all national and local environmental 
regulations.
Toner save feature 
If you want to reduce toner consumption, set the toner 
save setting to ON (feature #482 on page 58). The toner 
cartridge will last approximately 40 % longer. This 
feature may lower the print quality.
1.6 Output tray
Pull the output tray extender (1) forward gently until it 
clicks into place, then press the centre part of the 
extender (2) to open.
Note:
LDo not place the unit in an area where the output tray 
may be easily bumped into.
LThe output tray can hold up to approximately 150 
sheets of printed paper. Remove the printed paper 
before the output tray becomes full.
2
1
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 16  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
17
If the top part of the extender is detached
1.With the top part of the extender in the open position, 
insert the tab (1) into the left hole (2) of the 
extender.
2.Slide the other tab (3) into the right hole (4) of the 
extender from below until it clicks into place.If the extender is detached
1.Line up the extender (1) with the left side of the 
output tray. Make sure that the triangles (2) match, 
to attach the extender correctly.
2.Snap the extender (3) into the unit by pushing down 
the right side of the extender.
2
1
4
3
1
2
3
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 17  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
18
1.7 Recording paper
The paper input tray unit can hold:
– Up to 250 sheets of 60 g/m2 to 75 g/m2 paper.
– Up to 230 sheets of 80 g/m2 paper.
– Up to 200 sheets of 90 g/m2 paper.
LPlease refer to page 93 for information on recording 
paper.
LThe unit is set for printing A4 size paper by 
default. If you want to use letter or legal size 
paper, change the setting (feature #380 on page 
57).
1Pull the paper input tray (1) until it clicks into place, 
then pull it completely out, lifting the front part of the 
tray.
2Before loading a stack of paper, fan the paper to 
prevent paper jams.
3Load the paper, print-side up (2).
Important:
LPush and lock the plate (3) in the paper input 
tray, if it is lifted.
4Adjust the recording paper guides. Pinch the front 
side of the recording paper guide (4), then slide it to 
match the paper size mark.
Pinch the right side of the recording paper guide 
(5), then slide it to adjust the width to the size of the 
recording paper.
LMake sure that the recording paper is under the 
paper limit mark (6), and the paper should not 
be loaded over the snubbers (7).
1
3
2
7
6
5
4
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 18  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
19
5Insert the paper input tray to the unit, lifting the front 
part of the tray. Then push it completely into the unit.
Note:
LIf the paper is not loaded correctly, re-adjust the 
paper guides, or the paper may jam.
LIf the paper input tray does not close, the plate in the 
paper input tray may be lifted. Push the paper and 
make sure that the paper is laid flat in the paper input 
tray.
Caution for the paper input tray
LDo not drop the paper input tray.
LHold the paper input tray with both hands when 
removing or installing. The paper input tray 
weighs approximately 2 kg when the recording 
paper is fully installed.
1.8 Handset unit (KX-MB773/KX-
MB783 only)
1Connect the handset cord (1).
2Connect the handset connector (2).
LRemove the seal from the handset unit 
connection jack if attached.
3Insert the tab (3) and rib (4).
Approx. 2 kg 
1
2
4
3
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 19  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals 
						

							1. Introduction and Installation
20
Caution:
LWhen moving the unit, be sure to hold by the 
grip. Do not hold by the handset unit.
To remove the handset unit
1.Pull the handset unit slightly forward (1), then lift it in 
the direction of the arrow (2) to remove the rib.
2.Remove the tab (3), then disconnect the handset 
connector (4). Correct Incorrect
1
2
34
MB263HX_773_783EX-PFQX2807ZC-OI-en.book  Page 20  Monday, August 6, 2007  11:42 AM
Downloaded From ManualsPrinter.com Manuals