Panasonic Kx Flb881 Operating Instruction Manual

9. Programmable Features
51
9.2 Basic features
Feature/CodeSelection
Setting the quick setup
{#}{1}{0}{0}You can print out the quick fax setup guide and select the desired receiving 
mode depending on your situation.
{1} “FAX ONLY” (default): Use only as a fax (page 42).
{2} “DIST. RING”: With the Distinctive Ring service (page 49).
{3} “EXT. TAM”: With an external telephone answering machine (page 44).
{4} “TEL ONLY”: Mostly phone calls (page 43).
1.{MENU} i {#}{1}{0}{0}
2.{SET}
3.Press {SET} again to...

9. Programmable Features
52
Changing the password for 
feature programming via 
remote operation
{#}{1}{5}{5}1.{MENU} i {#}{1}{5}{5} i {SET}
2.Enter the current password. i {SET}
LThe default password is “1234”.
3.Enter a new 4-digit password using 0–9. i {SET}
4.Enter the new password again. i {SET} i {MENU}
Note:
LIf you forget your current password, “0101” can always be entered in step 
2 to continue changing the password.
LThis password is also used for feature programming via web browser.
Setting...

9. Programmable Features
53
Setting the default operation 
mode timer
{#}{4}{6}{4}To set the timer before returning to the default operation mode (feature #463).
{0} “OFF”: Deactivates this feature.
{1} “30s”: 30 seconds
{2} “1min” (default): 1 minute
{3} “2min”: 2 minutes
{4} “5min”: 5 minutes
Setting toner save feature
{#}{4}{8}{2}{0} “OFF” (default): Deactivates this feature.
{1} “ON”: The toner cartridge will last longer.
Note:
LThis feature may lower the print quality by reducing toner consumption....

9. Programmable Features
54
9.3 Fax features
Feature/CodeSelection
Printing a confirmation report
{#}{4}{0}{1}{0} “OFF”: Confirmation reports will not be printed.
{1} “ON”: A confirmation report will be printed after every fax transmission.
{2} “ERROR” (default): A confirmation report will be printed only when fax 
transmission fails.
Setting the journal report to 
print automatically
{#}{4}{0}{2}{0} “OFF”: The unit will not print a journal report, but will keep a record of the 
last 30 fax transmissions...

9. Programmable Features
55
Setting the Error Correction 
Mode (ECM)
{#}{4}{1}{3}This feature is available when the sending / receiving fax machines are ECM 
compatible.
{0} “OFF”: Deactivates this feature.
{1} “ON” (default): If there is an error during fax transmission / reception, the 
unit will support the communication.
Setting the connecting tone
{#}{4}{1}{6}If you often have trouble when sending faxes, this feature allows you to hear 
connecting tones: fax tone, ring back tone and busy tone. You...

9. Programmable Features
56
Setting the output tray to use 
for faxing
{#}{4}{4}{1}You can select the output tray that will be used for printing received faxes.
{1} “#1”: Upper output tray (Up to approx. 100 sheets)
{2} “#2” (default): Lower output tray (Up to approx. 50 sheets)
Note:
LLists or reports printed by pressing {HELP} (page 18) or {MENU} (page 88) 
will be stacked on the upper output tray.
Receiving a fax into the 
computer
{#}{4}{4}{2}If you wish to receive a fax into the computer, activate...

9. Programmable Features
57
9.4 Copy features
Feature/CodeSelection
Changing the default copy 
resolution
{#}{4}{6}{1}To change the default resolution setting for copying.
{1} “TEXT/PHOTO”: For documents containing both text and photographs.
{2} “TEXT” (default): For documents containing only text.
{3} “PHOTO”: For documents containing photographs, shaded drawings, etc.
Setting the output tray to use 
for copying
{#}{4}{6}{6}You can select the output tray that will be used for copying.
{1} “#1”...

9. Programmable Features
58
9.5 PC print features
Feature/CodeSelection
Setting the input tray in PCL
®
{#}{7}{6}{0}You can select the input tray that will be used in PCL printing.
{1} “#1” (default): Paper input tray
{2} “#2”: Manual input tray
Setting the output tray in PCL
{#}{7}{6}{1}You can select the output tray that will be used in PCL printing.
{1} “#1” (default): Upper output tray (Up to approx. 100 sheets)
{2} “#2”: Lower output tray (Up to approx. 50 sheets)
Setting the number of copies 
in...

9. Programmable Features
59
Setting the font pitch/point in 
PCL
{#}{7}{7}{0}To set the font pitch/point to be used in PCL printing.
1.{MENU} i {#}{7}{7}{0} i {SET}
2.Enter the font pitch from “00.44” to “99.99”, or the point from “004.00” 
to “999.75”, using the dial keypad.
LThe default pitch is “10.00” and the default point is “012.00”.
3.{SET} i {MENU}
Setting the symbol set in PCL
{#}{7}{7}{1}To set the symbol set to be used in PCL printing.
1.{MENU} i {#}{7}{7}{1}
2.Press {V} or {^} repeatedly to...

9. Programmable Features
60
9.6 Scan features
Feature/CodeSelection
Setting the scan mode for 
Push Scan
{#}{4}{9}{3}{1} “VIEWER” (default): The scanned image will be displayed in the [Multi-
Function Viewer] window.
{2} “FILE”: The scanned image will be saved as a file.
{3} “E-MAIL”: The scanned image will be saved for e-mail attachment.
{4} “OCR”: The scanned image will be displayed in the OCR window.
Holding the previous 
scanning parameter for Push 
Scan
{#}{4}{9}{4}{0} “DISABLED” (default):...