Panasonic KX FLB758RU User Manual

							6.2. PROGRAMMING AND LISTS
The programming function s are used to program the various features and function s of the machine, and to test the machine.
This facilitates communication between the user and the service man while programming the unit.
6.2.1. OPERATION
There are 2 basic categories of programming function s, the User Mode and the Service Mode. The Service Mode is further broken
down into the normal and special programs. The normal programs are those listed in the Operating Instructions and are available
to the user. The special programs are only those listed here and not displayed to the user. In both the User and Service Modes,
there are Set Functions and Test Functions. The Set Functions are used to program various features and function s, and the Test
Functions are used to test the various function s. The Set Functions are accessed by entering their code, changin g the appropriate
value, then pressing the SET key. The Test Functions are accessed by entering their code and pressing the key listed on the menu.
W hile programming, to cancel any entry, press the STOP key.
6.2.2. OPERATION FLOW
71
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							6.2.3. SERVICE FUNCTION TABLE
CodeFunctionSet ValueEffectiveRangeDefaultRemarks
501Pause time setX 100 msec001~600030----------
502Flash timeX10ms01~9985----------
503Dial speed select1:10pps
2:20pps1, 21----------
520CED frequency select1:2100 Hz
2:1100 Hz1, 21See Symptom/Co untermeasure Table for long
distance and international calls in.
521International mode select1:ON 2:OFF1, 21See Symptom/Co untermeasure Table for long
distance and international calls in.
522Auto standby select1:ON 2:OFF1, 21The resolution reverts to the default when
transmission is complete.
523Receive equalizer select1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km1~41Set RX equalizer to automatical mode.
524Transmission equalizer select1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km1~41
527V8 Mode1:DISABLE
2:ENABLE1,22----------
529Memory clear for Call Service“START ”input
550Memory clear: To reset the value to the default one, except the top margin
(#853),left margin (#854),time/day (#001),logo (#002),Fax No.(#003),History
and Directory.“START ”input
551ROM checkSee TEST FUNCTIONS (P.74).
552DTMF signal tone test1:ON 2:OFF1, 22SeeTEST FUNCTIONS (P.74).
553Monitor on FAX communication
select1:OFF
2:PHASE B
3:ALL1~31Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
554Modem testSee TEST FUNCTIONS (P.74).
556Motor test0SeeTEST FUNCTIONS (P.74).
557LED testSeeTEST FUNCTIONS (P.74).
558LCD testSeeTEST FUNCTIONS (P.74).
561KEY testSeeTEST FUNCTIONS (P.74).
570BREAK % select1:61% 2:67%1, 21Sets the % break of pulse sialing according PBX.
573Remote turn-on ring number setX number of
rings01~9910Sets the number of rings before the unit starts to
receive a document in the TEL mode.
590FAX auto redial time setX number of
times00~9903Selects the number of redial times during FAX
communication (not including the first dial).
591FAX auto redial time disconnection
time setX second001~999065Sets the FAX redial interval during FAX
communication.
592CNG transmit select1:OFF
2:ALL
3:AUTO1~32Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG is output only when automatic dialing
is performed. OFF: CNG is not output at phase A.
Refer toSOMETIME THERE IS A TRANSMIT
PROBLEM (P.118).
593Time between CED and 300bps1:75 msec
2:500 msec
3:1 sec1~31SeeSymptom/Countermeasure Table for long
distance and international calls in. Refer to
RECEIVE PROBLEM (P.119).
594Overseas DIS detection select1:detects at
the 1st time
2:detects at
the 2nd time1, 21SeeSymptom/Countermeasure Table for long
distance and international calls in. Refer to
SOMETIME THERE IS A TRANSMIT
PROBLEM (P.118).
595Receive error limit value set1: 5%
2: 10%
3: 15%
4: 20%1~42If the number of errors during transmission
exceeds this value, the sending side terminates
the call.
596Transmit level setXdBm- 15~0010Selects the FAX transmission level. Refer to
SOMETIME THERE IS A TRANSMIT PROBLEM
(P.118)and RECEIVE PROBLEM (P.119).
598Receiving sensitivity01= -01 dBm20~4843Used when there is an error problem.
599ECM frame size1:256 2:641, 21----------
651W rite system program into the Flash Rom with a parallel cable.----------
655Call service 3 detection numberSeeCALL SERVICE TROUBLESHOOTING
GUIDE (P.92)
72
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							CodeFunctionSet ValueEffectiveRangeDefaultRemarks
717Transmit speed selection1: 33600BPS
2: 31200BPS
3: 28800BPS
4: 26400BPS
5: 24000BPS
6: 21600BPS
7: 19200BPS
8: 16800BPS
9: 14400BPS
10: 12000BPS
11: 9600BPS
12: 7200BPS
13: 4800BPS
14: 2400BPS1~141Adjusts the speed to start training during FAX
transmission. Refer to SOMETIME THERE IS A
TRANSMIT PROBLEM (P.118)
718Receive speed selection1: 33600BPS
2: 31200BPS
3: 28800BPS
4: 26400BPS
5: 24000BPS
6: 21600BPS
7: 19200BPS
8: 16800BPS
9: 14400BPS
10: 12000BPS
11: 9600BPS
12: 7200BPS
13: 4800BPS
14: 2400BPS1~141Adjusts the speed to start training during FAX
reception. Refer toRECEIVE PROBLEM (P.119)
771T1 timer1: 35 sec
2: 60 sec1, 21Sets a higher value when the response from the
other party needs more time during FAX
transmission.
774T4 timer×100 msec00~9900Use this function when delay occurs in the line
and communication.
(ex. Mobile comm) does not work well.
815Sensor checkSee TEST FUNCTIONS (P.74).
852Print test patternSeeTEST FUNCTIONS (P.74).
853Top margin1~53----------
854Left margin1~74SeeLSU (Laser Scanning Unit) SECTION
(P.183).
880History listSee HISTORY (Example of a printed out list)
(P.82).
881Journal 2 listSee PRINTOUT EXAMPLE (P.123).
882Journal 3 listSeePRINTOUT EXAMPLE (P.123).
73
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							6.3. TEST FUNCTIONS
The codes listed below can be used to perform simple checks of some of the unit’s function s. W hen complaints are received
from customers, they provide an effective tool for identifying the location s and causes of malfunctions.
Test ModeType of ModeCodeFunction
Operation after code input
MOTOR TESTService Mode“5”“ 5”“ 6”0: Recording paper feed
1: Auto Document feed (STANDARD)
2: Auto Document feed (FINE/SUPER FINE)
4: Carriage (STANDARD)
5: Carriage (FINE/SUPER FINE)
START
MODEM TESTService Mode“5 ”“ 5”“ 4”Telephone line circuit is connected automatically, output the following signals on
the circuit line.
1) OFF 2) V21 ter 300bps 3) V27 ter 2400bps 4) V27 ter 4800bps
5) V29 7200 6)V29 9600bps 7) V17 7200bps 8) V17 9600bps
9) V17 12000bps 10) V17 14400bps 11) V34 2400bps 12) V34 4800bps
13)V34 7200bps 14)V24 9600bps 15) V34 12000bps 16) V34 14400bps
17)V34 16800bps 18)V34 19200bps 19) V34 21600bps 20) V34 24000bps
21)V34 26400bps 22)V34 28800bps 23) V34 31200bps 24) V34 33600bps
25)1100Hz 22)2100Hz
START
ROM CHECKService Mode“5 ”“ 5”“ 1”Indicates the version and checks the sum of the ROM.
START
LCD CHECKService Mode“5 ”“ 5”“ 8”Checks the LCD indication.
Illuminates all the dots to check if they are normal.
START
DTMF SINGLE TESTService Mode“5 ”“ 5”“ 2”Outputs the DTMF as single tones. Used to check the frequencies of the
individual DTMF tones. Refer to DTMF SINGLE TONE TRANSMIT SELECTION
(P.75).
1....ON
2....OFF
LED CHECKService Mode“5 ”“ 5”“ 7”All LEDs above the operation panel board flash on and off, or are illuminated.
START
KEY CHECKService Mode“5 ”“ 6”“ 1”Checks the button operation.
Indicates the button code on the LCD while the button is pressed. Refer to
BUTTON CODE TABLE (P.75).
START (any key)
MEMORY CLEARService Mode“5”“ 5”“ 0”To reset the value to the default one, except the top margin (#853),left margin
(#854),time/day (#001),logo (#002),Fax No.(#003),History and Directory.
Please restart a power supply after clearing a memory.
START
High Voltage Power
Supply Board
CHECKService Mode“6 ”“ 2”“ 8”Refer to HIGH VOLTAGE VALUE CHECK POINT (P.149).
START
SENSOR CHECKService Mode“8”“ 1”“ 5”First of all, press the copy button, and confirm the action of ON/OFF.
For each sensor ’s operation, refer to SENSORS AND SWITCHES SECTION
(P.183). DSCPREDT*3F*AFHB
: LCD DISPLAYD: Document sensor:W hen a document is insert.
S: Scanner read Pos.:W hen the edge of the document is detected.
C: Cover of Printer:W hen the top cover is open.
P: Paper exist:W hen recording paper exists.
R: Pick up paper:W hen the edge of the recording paper is detected.
E: Exit sensor on:W hen exist sensor is on.
D: Develo per exist
T: Toner exist
*: None
3F: Temperature of fuser unit (2 digits)
:Refer to HEAT LAMP CONTROL CIRCUIT (P.199).
*: None
A: ADF Cover Open
:W hen the ADF Cover is open.
F: Document Cover Open:W hen the Document Cover is open.
H: ADF Home Sensor:W hen the ADF Home Sensor is on.
B: FB Home Sensor:W hen the FB Home Sensor is on.
START
74
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							Test ModeType of ModeCodeFunction
Operation after codeinput
PRINT TEST
PATTERNService Mode“8”“ 5”“ 2”1. Press “852”then the SET key in the service mode.
2. As “PATNO = ”is displayed on the LCD, enter the test pattern No. and press
the SET key.
3. W hen “No. =“is displayed on the LCD, enter the printing number and press the
SET key. (Press “00”for the infinite printing.)
4. “MODE ”is displayed on the LCD. Press “0”to start printing or press “1”to go
to the next screen.
5. W hen “1”is pressed at MODE, “INTVL =“is displayed on the LCD. Enter the
printing interval (00~99 sec).
6. The printing repeats the designated number of times at the programmed
printing intervals.
START
Note:
The numbers in the boxes (XXX) indicate the keys to be input for the various test modes.
6.3.1. DTMF SINGLE TONE TRANSMIT SELECTION
Note:After performing this check, do not forget to turn the setting off.
otherwise, dialing in DTMF signal will not work.
6.3.2. BUTTON CODE TABLE
75
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							 1. NO. 01
 2. NO.07
 3. NO.03
 4. NO.09
6.3.3. PRINT TEST PATTERN
76
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							6.4. REMOTE PROGRAMMING
If, after the call is connected, the customer describes the situation and it is determined that the problem can be corrected by
making parameter changes, this function makes it possible to change parameters such as the user code and service code from
another fax (using DTMF tones). Therefo re, travel to the customer´s location is not required. However, it is not possible to
change all the parameters remotely ( PROGRAM MODE TABLE(P.78)). The function used to accomplish this is remote
programming.
First, in order to check the current status of the service code parameter, print out the setup list (code: 991) and the service list
(code: 999) from the customer ´s fax machine.
Based on this, the parameters for the desired codes can be changed.
The procedure for changin g and listing parameters is described on ENTERING THE REMOTE PROGRAMMING MODE AND
CHANG ING SERVI CE CODES (P.77). Also, before exiting the remote programming mode, it is advisable to obtain a new list to
confirm that the changes were made correctly.
Hint: Since the connected telepho ne is in use during the remote programming mode, it may be helpful to ask the customer to switch
to the speakerphone . This frees the customer from the need to remain right next to the fax while you are making parameter
settings. W hen finished , inform the customer. Also note that in very noisy location s where the DTMF tones are not audible , the
remote programming function will not work.
6.4.1. ENTERING THE REMOTE PROGRAMMING MODE AND CHANGING SERVICE CODES
CROSS REFER ENCE:
PROGRAM MODE TABLE (P.78)
77
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							6.4.2. PROGRAM MODE TABLE
CodeFunctionSet ValueDefaultRemoteSetting
001Set date and timedd/mm/yy hh:mm01/Jan/2003NG
002Your logo---------NoneNG
003Your fax telephone number---------NoneNG
004Transmission report mode1:Error / 2:ON / 3:OFFOFFOK
006FAX ring count1 to 9 rings2OK
012Remote TAM activationON/ID=11 / OFFOFFNG
013Dialing mode1:PULSE / 2:TONEPULSEOK
015PC INTERACE1:PARALLEL / 2:USBPARALLELNG
016Paper size1:LETTER / 2:A4 / 3:LEGALA4OK
017Ringer pattern1:A / 2:B / 3:CANG
022Auto journal print1:ON / 2:OFFONOK
023Overseas mode1:NEXT FAX / 2:ERROR / 3:OFFERROROK
025Delayed transmission1:ON / 2:OFFOFFNG
031Ring detection1:OFF/ 2:A / 3:B/ 4:C /5:DOFFOK
037Auto REDUCTION1:ON / 2:OFFONOK
039LCD contrast1:NORMAL / 2:DARKERNORMALNG
041Remote FAX activation code1:ON / 2:OFFON CODE=*#9NG
044Receive alert1:ON / 2:OFFONOK
048Language1:RUSSIAN / 2:ENGLISHRUSSIANOK
058LCD contrast1:NORMAL / 2:LIGHT / 3:DARKERNORMALOK
068ECM Selection1: ON / 2: OFFONOK
076FAX tone1:ON / 2:OFFONOK
079Toner save1:ON / 2:OFFOFFOK
080Set defaultYES / NONONG
501Pause time set001~600 x 100msec030OK
502Flash time01~99 x 10ms85OK
503Dial speed1:10pps / 2:20pps10OK
520CED frequency select1:2100Hz / 2:1100Hz2100OK
521International mode select1:ON / 2:OFFONOK
522Auto standby select1:ON / 2:OFFONOK
523Receive equalizer select1:0kms / 2:1.8km / 3:3.6km / 4:7.2km0kmOK
524Transmission equalizer select1:0kms / 2:1.8km / 3:3.6km / 4:7.2km0kmOK
527V8 Mode1:DISABLE /2:ENABLEENABLEOK
529Memory clear for Call Service------------------NG
550Memory clear------------------NG
551ROM check------------------NG
552DTMF signal tone test1:ON / 2:OFFOFFOK
553Monitor on FAX communication1:OFF / 2:Phase B / 3:ALLOFFOK
554Modem test------------------NG
556Motor test------------------NG
557LED test------------------NG
558LCD test------------------NG
561Key test------------------NG
570BREAK % select1:61% 2:67%61%OK
573Remote turn-on ring number01~9910OK
590FAX auto redial time set00~9903OK
591FAX auto redial line disconnection time set001~999sec065OK
592CNG transmit select1:OFF / 2:ALL / 3:AUTOALLOK
593Time between CED and 300bps1:75ms / 2:500ms / 3:1sec75msOK
594Overseas DIS detection select1:1st / 2:2nd1stOK
595Receive error limit value set1:5% / 2:10% / 3:15% / 4:20%10%OK
596Transmit level set-15~00dBm10OK
598Receiving Sensitivity20~4843OK
599ECM Frame size1:256 / 2:64256byteOK
655Call service 3 detection number00~06---------NG
717Transmit speed select1:33600/ 2:31200/ 3:28800/ 4:26400/
5:24000/ 6:21600/ 7:19200/ 8:16800/
9:14400/ 10:12000/ 11:9600/ 12:7200/
13:4800/ 14:240033600bpsOK
718Receive speed select1:33600/ 2:31200/ 3:28800/ 4:26400/
5:24000/ 6:21600/ 7:19200/ 8:16800/
9:14400/ 10:12000/ 11:9600/ 12:7200/
13:4800/ 14:240033600bpsOK
771T1 timer1:35s / 2:60s35sOK
774T4 timer00~99 ×100msec00OK
78
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							CodeFunctionSet ValueDefaultRemoteSetting
815Sensor test------------------NG
852Print test pattern------------------NG
853Top margin1~53OK
854Left margin1~74OK
880History list1:Start---------NG
881Journal 2------------------NG
882Journal 3------------------NG
991Setup list1:Start---------OK
994Journal list1:Start---------OK
995Journal 2 list1:Start---------OK
996Journal 3 list1:Start---------OK
998History list1:Start---------OK
999Service list1:Start---------OK
OK means “can set ”.
NG means “can not set ”.
Note:
Refer to SERVICE FUNCTION TABLE (P.72) for descriptions of the individu al codes.
Example: If you want to set value in the “004 Transmission report mode ”, press the dial key number 1, 2 or 3 corresponding to the Set
Value you want to select. (1:ERROR/2:ON/3:OFF)
79
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 
						

							6.4.3. USER MODE (The list below is an example of the SYSTEM SETUP LIST the unitprints out.)
Note:
The above values are the default values.
80
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals