Panasonic Hdc Z10000 Owners Manual

61VQT3U98
Adjusting the audio input level
∫Adjusting the input level of the built-in microphone (5.1 ch)
≥Set the [MIC SETUP] to anything other than [2ch]. ( l57)
1Select the menu.
2(When [SET]/[SET r] is selected)
Touch  /  to adjust the microphone 
input level.
≥Touch   to activate/disactivate ALC. When ALC is 
activated, the icon is surrounded by yellow and the 
amount of sound distortion can be reduced. When 
ALC is disactivated, natural recording can be 
performed.
≥ Adjust the microphone input...

62VQT3U98
Adjusting the input level of the built-in microphone (5.1 ch) using the operation 
icons
≥Set the [MIC SETUP] to anything other than [2ch]. ( l57)
≥ Set [5.1ch MIC LEVEL] to [SET]/[SET r]. (l61)
1 Display the operation icons and touch  . ( l78)
2 Touch  /  to adjust settings.
3 Touch   to complete the setting.
∫ Adjusting the input level of the built-in microphone (2 ch), external 
microphone or audio device
≥Set [MIC SETUP] to [2ch]. ( l57)
Adjust the input level operating the Audio control...

63VQT3U98
You can change a counter display that indicates how much time has elapsed during 
recording or playback.
Recording
Counter display
Counter displayIndications
Time Code TC 00:00:00:00 or TC 00:00:00.00
≥
Display will change depending on the setting of the 
[TC MODE]. ( l64)
User Information ( l65) UB 00 00 00 00
Recording Counter ( l66) (In Recording Mode)
00:00:00 or SCN 00:00:00
(In Playback Mode)
SCN 00:00:00
≥
In Recording Mode, display will change depending on 
the setting of the [REC...

64VQT3U98
Setting the Time Code
Time code will display the recording time in hours, minutes, seconds, and frames.
TC 00:00:00:00 (hour : minute : second : frame [NDF])
TC 00:00:00.00 (hour : minute : second . frame [DF])
≥The frame (Number of frames counted every second) will vary depending on the 
[REC FORMAT] setting. ( l11 5 )
Select the compensation mode for the time code.
≥ It is automatically set to [NDF] when the [REC FORMAT] is set to [1080/24p] or the interval 
recording is used.
Sets the way...

65VQT3U98
You can set the initial time code.
1Select the menu.
2Touch the item to set and change with  / .
≥It will be set to 00h00m00s00f when the RESET button is pressed.
≥ “h” is an abbreviation for hour, “m” for minute, “s” for second and “f” for frame.
3Touch [ENTER].
≥Touch [EXIT] to complete the setting.
≥This unit will adjust the time code in accordan ce with the frame rate of the recording format. 
( l 115) Therefore, it may not be continuous from the previous final time code when the 
recording...

66VQT3U98
Setting the Recording Counter
Recording Counter will display the recording time in seconds.
00:00:00 (hour : minute : second (When [REC COUNTER] is set to [TOTAL]))
SCN 00:00:00 (hour : minute : second (When [REC COUNTER] is set to [SCENE]))
Select the counting method during the recording.
To reset the Recording Counter for the Recording ModeThe Recording Counter will be set to 00:00:00 when the RESET button is pressed while 
displaying the counter.
[REC COUNTER]
: [SW & DISP SETUP]  # [REC...

67VQT3U98
Each of the USER button can register one function from the 18 available functions.
≥ There are three USER buttons (USER1 to USER3) on the main body and four USER 
button icons (USER4 to USER7) displayed on the LCD monitor.
Setting the USER button
1Select the menu.
2Touch the USER button you wish to set.
≥The USER button number and currently set function name are displayed. (For example, a 
display of 1. [FA] means that Focus Assist has been assigned to USER1 button.)
3Touch the item to...

68VQT3U98
Using the USER button
To use the set USER button, press USER1 to USER3 button or touch the USER4 to USER7 
button icon displayed when you touch the LCD monitor.
(When you use the USER1 to USER3) (When you use the USER4 to USER7)
≥To cancel, press the USER button or touch the USER button icon again.
For canceling or using of the following functions for the USER buttons, refer to each page.
jPush AF ( l69)
j Black Fade ( l70)
j White Fade ( l70)
j Digital Zoom ( l71)
j Playback parallax...

69VQT3U98
Functions of the USER button
∫List of USER button function
*1 It is not possible to use in Playback Mode.
*2 It is not possible to use in Recording Mode.
It can be temporary changed to Auto Focus when it is set to Manual Focus. ( l51)
Press and hold the USER button, or touch and hold the USER button icon in the 
recording screen.
≥ It will be canceled when t he button is released.
≥The focus position set by the Push AF will be maintained when canceled.
Switches to automatic iris control to...

70VQT3U98
Switches to automatic iris control for spotlight.
Very bright object is recorded clearly.
≥ appears when it is set.
≥ It will return to standard Auto Iris Mode ( ) when it is canceled. ( l54)
Fade in/fade out effect (black) can be added to the video and audio that is being recorded.
Press USER button or touch USER button icon in the recording screen.
≥ Fade out will start, and fade in will start after completing the fade out.
≥ It will fade out when the button is pressed and held, and fade in...