Panasonic Hdc Z10000 Owners Manual

21VQT3U98
Connecting to the AC outlet
Important:
≥Use the supplied AC adaptor. Do not use the AC adaptor of another device.
≥ Do not use the AC cable with any other equipment as it is designed only for this unit. 
Also, do not use the AC cable from other equipment with this unit.
A AC cable (K2CB2CB00022; supplied)
≥ Insert the plugs as far as they will go.
1Connect the AC cable to the 
AC adaptor and the AC outlet.
≥Use the AC cable (K2CB2CB00022; 
supplied) dedicated for the AC adaptor.
2Connect the AC...

22VQT3U98
The unit can record motion pictures or still pictures to an SD card.
Cards that you can use with this unit
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for 
motion picture recording.
* SD Speed Class Rating is the speed standard regarding continuous writing. 
Check via the label on the card, etc.
≥Please confirm the latest information abo ut SD Memory Cards/SDHC Memory Cards/
SDXC Memory Cards that can be used for motion picture recording on the following...

23VQT3U98
Inserting/removing an SD card
Caution:
Check that the access lamp has gone off.
1Open the SD card slot cover 
and insert (remove) the SD 
card into (from) the card slot 
B.
≥One SD card can be inserted into each of 
the card slot 1 and the card slot 2.
≥ Face the label side  C in the direction 
shown in the illustration and press it 
straight in as far as it will go.
≥ Press the center of the SD card and then 
pull it straight out.
2Securely close the SD card slot 
cover.
≥Securely close it...

24VQT3U98
Set the power switch to ON while pressing the lock release button B to 
turn on the unit.
A The status indicator lights on.
≥To turn on the unit again after the [ECONOMY (BATT)] or [ECONOMY (AC)] is activated, 
set the power switch to OFF once, and then to ON again. ( l128)
Change the mode to recording or playback.
Operate the mode switch to change the mode to   or  .
Preparation
Turning the unit on/off
Preparation
Selecting a mode
Recording Mode ( l36, 45)
Playback Mode ( l79)

To turn off...

25VQT3U98
The viewfinder is turned off and the LCD monitor is turned on when the LCD monitor is 
extracted. The viewfinder is turned on when the LCD monitor is retracted.
Live image recording or 3D recordings can be viewed in 3D on the LCD monitor.
Using the LCD monitor
1Extract the LCD monitor in the 
direction as indicated in the 
figure.
≥Hold the LCD monitor extract part  A when 
pulling out.
2Rotate to the position that is easy to 
view.
To retract the LCD monitorRetract as shown in the figure with...

26VQT3U98
How to use the touch screen
You can operate by directly touching the LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate with 
your fingers.
∫Touch
Touch and release the touch screen to select icon or 
picture.
≥Touch the center of the icon.
≥ Touching the touch screen will not operate while 
you are touching another part of the touch screen.
∫ Slide while touching
Move your finger while pressing on the...

27VQT3U98
LCD monitor adjustment
≥These settings will not affect  the images actually recorded.
This makes it easier to view the LCD monitor in bright places including outdoors.
Select the menu. ( l30)
≥It cannot be set when LCD monitor is set to 3D viewing.
≥ When the AC adaptor is in use, [POWER LCD] is set to [ON] automatically.
≥ Recordable time with the battery is shortened when the LCD is made brighter.
It adjusts brightness and color density on the LCD monitor.
1 Select the menu. ( l30)
2 Touch...

28VQT3U98
Viewfinder adjustment
≥These settings will not affect  the images actually recorded.
It adjusts the field of view to show  the image on the viewfinder clearly.
1 Adjust the viewfinder according to the 
position that is easy to view.
≥Be careful not to trap your fingers when moving the 
viewfinder.
≥ The viewfinder can be lifted vertically up to 
approximately 90 o.
≥ Retract the LCD monitor and turn on the viewfinder.
2 Adjust the focus by operating the eyepiece 
corrector lever.
Brightness of...

29VQT3U98
When the unit is turned on for the first time, a message asking you to set the date and time 
will appear.
Select [YES] and perform steps 2 to 3 below to set the date and time.
1Select the menu. (l30)
2Touch the date or time to be set, then set 
the desired value using  / .
≥The year can be set between 2000 and 2039.
≥ The 12-hour system is used to display the time.
3Touch [ENTER].
≥The screen may switch to the setting screen for the [TIME ZONE]. Touch the screen and 
set the [TIME ZONE].
≥...

30VQT3U98
1Press the MENU button  .
2Touch the top menu A.
3Touch the submenu B.
≥Next (Previous) page can be displayed by 
touching / .
4Touch the desired item to enter 
the setting.
5Touch [EXIT] to exit the menu 
setting.
Preparation
Using the menu screen
MENU
MENU
HDC-Z10000P-VQT3U98_mst.book  30 ページ  ２０１１年１０月１７日　月曜日　午後２時２４分