Panasonic Hdc Z10000 Owners Manual

31VQT3U98
Select the menu.
1 Power on/off button [ ]
The unit can be turned on/off when the 
power switch of this unit is set to ON.
≥It will not be possible to turn the unit on 
with the wireless remote control 
approximately 36 hours after turning the 
unit off. To turn the unit on again, set the 
power switch of this unit to OFF once, and 
then to ON.
≥ Unit cannot be turned off when it is 
connected to the PC.
2 Photoshot button [ ]
*
3 On-screen display button  [EXT DISPLAY] ( l89)
4 Playback...

32VQT3U98
∫Wireless remote control usable range
A Wireless remote control sensor
Distance: Within approx. 5 m (16 feet)
Angle: Approx. 15 o up, down, left and right
≥ The wireless remote control is intended for indoor operation. Outdoors or under strong 
light, the unit may not operate properly even within the usable ranges.
Operation of direction buttons/OK button
1Press a direction button.≥Selected item will become yellow.
2Select the item with the 
direction button.
3Confirm the selection by 
pressing...

33VQT3U98
∫Basic camera positioning
Normal recording
≥ Put your hand through the grip belt and 
hold the unit with both hands.
Recording from a high position Low-angle recording
≥
For easier low-angle recording, the sub 
recording start/stop button and the sub 
zoom lever can be used.
Recording
Before recording
HDC-Z10000P-VQT3U98_mst.book  33 ページ  ２０１１年１０月１７日　月曜日　午後２時２４分 

34VQT3U98
≥When recording, make sure your footing is stable and there is no danger of colliding with 
another person or object.
≥ Hold the eye cup of the viewfinder as close as possible to your right eye.
≥ Adjust the angle of the LCD monitor according to the position in which the unit is held.
≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is 
backlit, it will become dark in the recording.
≥ Keep your arms near your body and separate your legs for better balance.
≥...

35VQT3U98
[SD CARD 1] and [SD CARD 2] can be selected separately to record motion pictures or still 
pictures.
1Select the menu.
2Touch the media to record motion 
pictures or still pictures.
≥The media is selected separately to motion pictures 
or still pictures is highlighted in yellow.
3Touch [ENTER].
Recording
Selecting a media to record
: [SW & DISP SETUP]  # [MEDIA SELECT] #  [YES]MENU
HDC-Z10000P-VQT3U98_mst.book  35 ページ  ２０１１年１０月１７日　月曜日　午後２時２４分 

36VQT3U98
You can record life-like and powerful 3D full high definition quality video.
* The image is an illustration.
≥This unit can record a 3D full high definition quality video in AVCHD 3D recording 
format.
≥ Refer to page 91 for viewing 3D full high definition quality video with a 3D compatible TV.
≥ It is possible to record while checking the 3D video when the LCD monitor is used.
1Change the mode to  .≥Extract the LCD monitor.
2Select the menu.
≥  appears when [3D/2D REC MODE] is set 
to [3D]....

37VQT3U98
∫Screen indications in the Recording Mode
*1 Only displayed when 3D Recording Mode is in use.
*2 Only displayed when 2D Recording Mode is in use.
≥To record effective image as a 3D, it is recommended to adjust the convergence point as 
necessary. ( l39)
≥ The default setting of [3D/2D REC MODE] is [3D].
≥ The images recorded between pressing the recording start/stop button to start recording 
and pressing it again to pause recording become one scene.
≥ Up to approximately 3,900 scenes can be...

38VQT3U98
To ensure that the 3D video can be safely viewed, pay attention to the following 
points when recording.
≥Do not get too close to the subject. (U se the 3D guide display as guidance. ( l41))
*
* It is possible to get close to approximately 45 cm (1.5 feet) when the 3D macro is used. 
(l 73)
≥ When moving the unit as you record, move it slowly.
≥ Try to hold the unit as steady as possible when recording while riding in a vehicle or 
walking.
About the compatibility of the recorded motion...

39VQT3U98
Convergence point adjustment
∫About the convergence point
Convergence point is a position that becomes the reference plane of the 3D image.
When viewing the 3D image, a subject located closer than the convergence point is 
displayed in front of the screen, and a subject located farther than the convergence point is 
displayed behind the screen.
∫Adjusting the convergence point
It is recommended to prepare for recording, such as adjust the convergence point in 
accordance with the position of...

40VQT3U98
2Rotate the CONV. dial to adjust the 
convergence point.
≥This can be set between C00 and C99. Position of the 
convergence point will be set further when the number 
is larger.
≥ The subject at the position of the convergence point will 
not shoot out or recess from the screen. (It is seen as 
same as the 2D image)
≥ Adjust by checking on the 3D image or 3D guide display 
on the LCD monitor. ( l41)
≥ When zooming, it may be necessary to readjust the convergence point.
About Convergence...