Panasonic DLP Based Projector PT-D10000U PT-DW10000U Operating Instructions

ENGLISH – 101
Special Features
 
Changing the text
The characters displayed in the text can be changed 
when “ON” has been selected as the “TEXT 
DISPLAY” setting.
1. Press ▲▼ to select “TEXT 
CHANGE”.
2. Press ENTER.
The “TEXT” screen will be displayed.
3. Press ◄► to select the text 
position, and press ▲▼ to select 
the characters of the text.
4. Press ENTER.
The text is now changed. •
•
SECURITY
PASSWORD
PASSWORD CHANGE
TEXT DISPLAY
TEXT CHANGE
    MENU SELECT
    SUB MENUOFF
OFF
ENTER
SECURITY...

102 – ENGLISH
The main unit is equipped with SERIAL terminals located in its connection terminals, and this terminal is compliant 
with RS-232C/RS-422. Also a serial output terminal is provided to enable plural projector control.
Examples of connection
For RS-232C
Single projector
Plural projectors
Pin assignments and signal names
Communication conditions (Factory setting)
■
●
●
■
■
RS-232C IN RS-422 IN
RS-422 OUTSERIAL
PC
D-Sub 9-pin (male)
Communication cable (straight) Connection terminals on...

ENGLISH – 103
Special Features
For RS-422
Single projector
Plural projectors
Pin assignments and signal names
Communication conditions (Factory setting)
■
●
●
■
■
RS-232C IN RS-422 IN
RS-422 OUTSERIAL
PC
D-Sub 9-pin (male)
Communication cable (straight) Connection 
terminals on 
projectorD-Sub 9-pin (female)
RS-232C IN RS-422 IN
RS-422 OUTSERIAL
PC
D-Sub 9-pin (male)
Communication cable (straight) Connection 
terminals on 
projectorD-Sub 9-pin (female)
RS-232C IN RS-422 IN
RS-422 OUTSERIALRS-232C IN...

104 – ENGLISH
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this 
order. Add parameters according to the details of control.
Attention
No command can be sent or received for 10 to 60 seconds after the lamp starts lighting. Try sending any 
command after that period has elapsed.
When transmitting multiple commands, be sure to wait until 0.5 of a second has elapsed after receiving the 
response from the projector before sending the next...

ENGLISH – 105
Special Features
Cable specifications
Connecting to a PC
For RS-232C
When multiple projectors are connected
Attention
To connect the computer to the SERIAL terminal, prepare an adequate communication cable that fits to your 
personal computer.
■
●
●
•
1
2
3
4
5
6
7
8
91
2
3
4
5
6
7
8
9NC NC
NC NC
NC NC
NC NC
ProjectorComputer (DTE 
specifications)
1
2
3
4
5
6
7
8
91
2
3
4
5
6
7
8
9NC NC
NC NC
NC NC
NC NC
ProjectorComputer (DTE 
specifications)
1
2
3
4
5
6
7
8
91
2
3
4
5
6
7
8
9
1st 
(RS-422...

106 – ENGLISH
Using the REMOTE 2 terminal provided on the connection terminals of the main unit, it is possible to operate the 
projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot be 
received.
Example of a control panel layout
Pin assignments and control
Be sure to short-circuit Pins # and - when controlling.
Note
When pin # and pin - are short-circuited, the following buttons on the projectors control panel and on the 
remote control cannot be...

ENGLISH – 107
Information
 
Indication of monitor lamp
Five monitor lamps are provided at the top of main unit front to inform the user of the lamp replacement time and 
unusual internal temperature. These lamps indicate the degree of abnormality by combination of blinking and/or 
lighting lamps. Turn off the power and take the proper measure according to the table below.
Attention
Be sure to observe the procedure “Powering up the projector” (p. 35) and “Powering off the projector” (p. 36) 
when...

108 – ENGLISH
  Cleaning and replacement of air filter
If the air filter is blocked with too much dust, the inside of the projector will become hot and the temperature monitor 
(TEMP) indicator will flash and the power will turn off. The static electric mesh filter should be replaced and the 
metal mesh filter and brush inside the filter unit should be cleaned after approximately 2 000 hours of use, although 
this is a guide only and the actual time will vary depending on the operating conditions....

ENGLISH – 109
Information
Note
If cleaning cannot remove the dust completely, then it is a sign to replace the static electric mesh filter. Consult 
the dealer. In addition, when the lamp unit is replaced, also replace the static electric mesh filter.
Do not wash the static electric mesh filter with water. 
Use a neutral detergent to clean off any oil from the movable metal mesh filter.  •
•
•
7.  Install the movable metal mesh 
filter to the filter cleaning unit. 
When reassembling, align the edge of...

110 – ENGLISH
Precautions on lamp unit replacement
Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled, 
failure might result.
A used lamp unit may burst if it is handled violently. For disposition of used lamps, request an industrial waste 
disposal contractor.
If you continue to use a lamp after the replacement time, the lamp may break.
Phillips screwdriver is necessary when replacing a lamp unit. Take care not to slip your hand when using a...