Panasonic DLP Based Projector PT-D10000U PT-DW10000U Operating Instructions

ENGLISH – 91
Special Features
E-mail setup page
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can 
be sent to one or more preset e-mail addresses (maximum two addresses). Click [Projector Control], then 
[E-mail set up] to display the E-mail setup page.
■
Select “Enable” to use the E-mail 
function.
Enter the IP address or server name 
of the E-mail server (SMTP). The 
DNS server must be set if the server 
name is entered.
Enter the E-mail...

92 – ENGLISH
E-mail setup page (continued)■
Periodic warning interval setting 
(E-mail is sent on the checked days of 
the week/times)Periodic warning interval setting 
(E-mail is sent on the checked days of 
the week/times)
Enter the E-mail address to which the 
E-mail is to be sent when two E-mail 
addresses are going to be used. Do 
not enter it when the second E-mail 
address is not going to be used.
Select the conditions for sending 
E-mail.
MAIL CONTENTS:
Select “NORMAL” or “SIMPLE”.
ERROR:
an...

ENGLISH – 93
Special Features
DNS server set up page
Click [Network set up], then [DNS server set up] to display the DNS server set up page.
■
Button to update settings Check these boxes when E-mail is 
to be sent periodically to two E-mail 
addresses. E-mail will be sent at the 
times and on the days checked.Button to update settings Check these boxes when E-mail is 
to be sent periodically to two E-mail 
addresses. E-mail will be sent at the 
times and on the days checked.
Button to update settings...

94 – ENGLISH
Authentication server setting page
The POP server is set on this page when POP authentication is required for mail transmissions.
Click [Network set up], then [
Authentication set up] to display the POP server setup page.
Ping test page
This page makes it possible to check whether the network is connected to the E-mail server, POP server, DNS 
server, etc.
Click [Network set up], then [Ping test] to display the Ping test page.
■
■
Select the authentication method 
specified by your Internet...

ENGLISH – 95
Special Features
Contents of mail sent
Mail with the contents shown below is sent when the E-mail settings have been 
established.
Mail with the contents shown below is sent when an error has occurred.
■
●
●
Subject: Panasonic projector report(CONFIGURE)
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : D10000
-----  E-mail setup data -----
TEMPRATURE WARNING SETUP 
MINIMUM TIME            at [ 60] minutes interval 
INPUT AIR TEMPERATURE   Over [ 35C / 95F ] 
OUTPUT AIR...

96 – ENGLISH
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
Note
If the time becomes incorrect immediately after setting the correct time, then the battery needs to be changed. 
Contact the dealer where you bought the projector to have the battery changed.
Network config page
Click [Network set up], then [Network config] to display the Network config page.
■
•
■
Time zone selection
Button to update time zone setting
Button to update time and date 
settings...

ENGLISH – 97
Special Features
Firmware update page
(The firmware should be updated only by an individual with the specialized knowledge required to do this.)
Messages such as the ones shown below appear during data rewriting.
The following message appears upon completion of the version data rewriting.
■
Enter here the filename of the 
firmware to be updated.
After entering the filename, press the 
[Upload] button. Data transfer is now 
commenced.
It will take several dozen seconds for 
the data to be...

98 – ENGLISH
The network functions of this projector are compatible with PJLink™ Class 1, and so the PJLink™ protocol can be 
used to carry out the following operations from a computer.
Projector settings
Querying the projector status
Supported commands
The following table lists the PJLink™ protocol commands that can be used to control the projector.
PJLink™ security authorization
The password used for PJLink™ is the same as the password which has been set for web browser control. If 
you would like to...

ENGLISH – 99
Special Features
Displaying the security 
screen
Password settings and text settings can be made after 
the security screen is displayed.
If using for the first time
1. Press ▲, ►, ▼, ◄, ▲, ►, ▼ and 
◄ in this order.
If the existing password has been 
changed
  Enter the new password.
2. 
Press ENTER.
The “SECURITY” screen will be displayed.
Note
Only asterisks * will appear on the screen to 
represent the actual characters of the password 
when the password is entered.
  Setting the...

100 – ENGLISH
2. Press ◄► to switch 
“PASSWORD”.
The setting will change as follows each time 
◄► is pressed.
OFFON
ON:
Password entry is enabled.
OFF:
Password entry is disabled.
  Changing the password
The password can be changed.
1. Press ▲▼ to select 
“PASSWORD CHANGE”.
2. Press ENTER.
The “PASSWORD” screen will be displayed.
3. Press ▲▼◄► to set the 
password.
Up to 8 buttons can be set as the password.
4. Press ENTER.
5.  For the purposes of 
confirmation, enter the password 
again.
6. Press...