Panasonic DLP Based Projector PT-D10000U PT-DW10000U Operating Instructions

ENGLISH – 61
Basic Operation
 
Blanking adjustment
Blanking adjustment fine-tunes the images projected 
by the video deck or other devices when the noise 
appears on the edges of the screen or if a part of the 
image lies slightly offscreen.
1. Press ▲▼ to select  “BLANKING”.
2. Press ENTER.
The “BLANKING” adjustment screen will be 
displayed.
3. Press ▲▼ to select the desired 
item for adjustment.
4. Press ◄► to adjust blanking.
The adjustment value for the PT-D10000U can 
be changed within a range of 0...

62 – ENGLISH
Note
The abovementioned vertical stripes will not appear 
on the screen when all signals are input.
The picture may be distorted during the adjusting 
operation, but this is not a fault.
The input resolution can be adjusted only when 
RGB signal input is applied with RGB1 and RGB2 
IN.
  Adjusting the clamp 
position
Use the clamp position adjustment to achieve the 
optimal value when dark areas of the image are 
crushed or displayed in green.
1. Press ▲▼ to select  “CLAMP 
POSITION”.
2....

ENGLISH – 63
Basic Operation
4. Press ▲▼ to specify the area to 
be adjusted.
To joint the top: set “UPPER” to “ON”.
To joint the bottom: set “LOWER” to “ON”.
To joint the left: set “LEFT” to “ON”.
To joint the right: set “RIGHT” to “ON”.
5.  Press ENTER to toggle “ON” and 
“OFF”.
6. Press ◄► to adjust the 
compensation width and start 
position.
To display the adjustment 
marker
7. Press ▲▼ to select “MARKER”.
8.  Press ENTER to select “ON”.
A marker for adjusting the picture position 
appears. The...

64 – ENGLISH
15. Use ◄► to adjust the width for 
correcting the “BRIGHT INSIDE” 
setting (0 to 255).
16. Press ▲▼ to select “BRIGHT 
OUTSIDE”
.
17. Press ENTER.
The “BRIGHT OUTSIDE” adjustment screen 
will be displayed.
When “INTERLOCKED” is set to “OFF”, 
individual adjustment of “R”, “G” and “B” will be 
possible.
18. Press ▲▼ to select an item, and 
press ◄► to adjust the setting.
•
•
BRIGHT ADJUST
BRIGHT INSIDE
BRIGHT OUTSIDE
UPPER
LOWER
LEFT
RIGHT 
    MENU SELECT
    ADJUST0
0
0
0BRIGHT ADJUST...

ENGLISH – 65
Basic Operation
Note
When “FRAME DELAY” is set to “SHORT”, 
deterioration in the picture quality will occur. 
Furthermore, the noise reduction function cannot be 
used.
  Raster position
When the whole area where the input picture can be 
displayed is not used, the picture can be moved to 
any position inside the display area.
1. Press ▲▼ to select “RASTER 
POSITION”
.
2. Press ENTER.
The “RASTER POSITION” screen will be 
displayed.
3. Press ▲▼◄► to adjust the 
position.
PT-D10000U
•
•
■...

66 – ENGLISH
Setting the DISPLAY LANGUAGE
This lets you switch the display language.
MENUPress to display the 
MAIN MENU screen.
Press to select “DISPLAY 
LANGUAGE”.
Press to display the 
“DISPLAY LANGUAGE” 
menu.
MENUPress to display the 
MAIN MENU screen.
Press to select “DISPLAY 
LANGUAGE”.
Press to display the 
“DISPLAY LANGUAGE” 
menu.
MAIN MENU
  PICTURE
  POSITION
  ADVANCED MENU
  DISPLAY LANGUAGE
  OPTION1
  OPTION2
  TEST PATTERN
  SIGNAL LIST
  NETWORK
  SECURITY
    MENU SELECT
    SUB MENU...

ENGLISH – 67
Special Features
Basic Operation
This menu can be used to make a variety of 
picture and projector settings.
MENUPress to display the 
MAIN MENU screen.
Press to select 
“OPTION1”.
Press to display the 
“OPTION1” menu.
MENUPress to display the 
MAIN MENU screen.
Press to select 
“OPTION1”.
Press to display the 
“OPTION1” menu.
MAIN MENU
  PICTURE
  POSITION
  ADVANCED MENU
  DISPLAY LANGUAGE
  OPTION1
  OPTION2
  TEST PATTERN
  SIGNAL LIST
  NETWORK
  SECURITY
    MENU SELECT
    SUB MENU...

68 – ENGLISH
Option1 settings (continued)
If “3COLORS” or “7COLORS” 
was selected in step 2.
3. Press ENTER.
The “COLOR MATCHING: 3COLORS” or 
“
COLOR MATCHING: 7COLORS” screen will 
be displayed.
4. Press ▲▼ to select “R”, “G” and 
“B”.
5. Press ENTER.
6. Press ◄► to adjust the values.
These values can be adjusted from 0 to 2048.
Note
The effects of correcting the adjustment color:
When tuning the correction color that is the same 
as the adjustment color: the brightness of the 
adjustment color...

ENGLISH – 69
Special Features
6.  Use the colorimeter to 
measure the luminance (Y) and 
chromaticity coordinates (x, y).
7. Press ▲▼ to select the colors, 
and press ◄► to select their 
values.
8.  After all the data has been input, 
press MENU.
The “MEASURE MODE” screen will be 
displayed.
Inputting the coordinates of a 
desired color
9. Press ▲▼ to select 
“MODE”.
10. Press ▲▼ to select “7COLORS”.
11. Press ▲▼ to select “TARGET 
DATA”
.
12. Press ENTER.
The “TARGET DATA” screen will be displayed.
13....

70 – ENGLISH
  Auto signal
When unregistered signals are to be input frequently 
because the unit is used at conferences or other 
venues, the screen display position can be adjusted 
automatically without having to press AUTO SETUP 
on the remote control each time.
1. Press ▲▼ to select “AUTO 
SIGNAL”.
2. Press ◄► to switch “AUTO 
SIGNAL”.
The setting will change as follows each time 
◄► is pressed.
OFFON
If unregistered signals are input when “ON” 
is selected, auto setup will be initiated...